Sears 385. 1884180 owner manual Zigzag foot, Control 3 to

Page 58

Sot the Machine

Stitch width control 5 to 6

2

C_

Top thread tension

:ontrol 3 to 8 Stitch length control 0.5 to 2

Stretch Stitch

A:Zigzag foot

The Stitch and Its Uses

Use this stitch to iota two pieces of

fabric to create an open work

appearance and add design interest.

Here's How

1.Fold under each fabric edge 5/8" and press.

2.Pin the two edges to paper or tear-away backing I/8" apart,

3.Sew s_owly, guiding the fabric so the needle catches the folded edge on each side.

Set the Machine

Stitch width

control 3 to 6

Top thread	tansson	Stitch	length
control 2 to	6	Stitch	length
		control	yel_aw
		stretch	stitch
		pos_on

Stretch Stitch

A:Zigzag foot

The Stitch and Its Uses

Use as hemming stitch for blankets,

tablecloth and draperies.

........... J

Here's How

Place the fabric top side up, and sew 3/8" from the edge.

Trim close to stitching. The stitch will prevent raveling.

56

Image 58

Contents Sewing Machine Sears Canada NC Kenmore Sewing MachineTable of Contents Know Your Machine Portable Case or Cabinet is AvailablePage Bobbin Plug in the Machine and Switch on the Power OFFPressure Dial should Reset at Machine is running= Thread Cutter = Setting Spool Pins= Adjust the Presser Foot Lever Foot= Free-Arm Sewing the Removable Extension Table To removeOranycirculargarmentarea Orareasofwearinchildrensclothes Etc To Attach Changethe Presser FootPresserFoot Types To Snap OnZigzag Foot Zipper Edges Sliding Buttonhole FootUse this GuideQu liter Topstitching = Presser Foot TypesButtonhole Foot FabNcs Check Your NeedleTo Change Your Needle Onto = To Remove the Bobbin from the Machine = Wind the BobbinPut Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Pick Up Your Bobbin Thread Toward InchesAdjust the Top Thread Tension TopIs set Indicator panelTop tension Too Tight Too Loose Is upStremh Stitch Position = Three Needle PositionWidth Needle positionThree Needle Position Sem On p Check ChartII1 III Refer to 52 ~3N6 Stitch ShellOn p.15 Onp Stitch Refer toCheck ZoneOn p 155 Turn a Square Corner Control 0 grog Use the Darning PlateUse the darning plate in the following ways Thread tensionControl 2 to Control orangeCenter Out HeresHow When you finish darning, remove the darningPlate and replace foot holder and foot Basle Zigzag Set the Machine Contro I toContro 3 to Very short Applique= Bar Tacking Pressure dial2Embroidery =dth control Sew a ButtonZigzag foot Darning plate = Rick-Rack Stretch Stitch length ControlThree-Step Zigzag Stitch width control 5 toSat the Machine Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Zi£rzegfootWeight Set the Machine Stitch width Control LightIlili!!ii!iiilji Cuffs = Learningto Sew ButtonholesHave Or where31controt Stitch wdthControl 3 to Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Lingerie Set the Machine Stitch widthControl 3 to 8Stitch Iength control orange zone Smocking Control 3 to 6 2Zigzag foot Stlchwidth control 3 to Zigzag tootIii¸!iiiiii¸...........i Stitch length controt Stitch width control 3 toPositron Contro green Satin stitchWhatto do when Insert IncorrectImproper Vacuum Cover plate byDriver Parts List 813404013 B868102403202 655t1920 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable Buttonhole Making 4551 Opener Template 6566Two-point Box Zipper Application 5253 Foot T2, 26 6566Settingupyourmachine Stitch SelectorPage Practical Stitch Chart FAGOT,NGWarranty Year385 Sewing MachineVisit