Sears 385. 1884180 owner manual Stlchwidth control 3 to, Zigzag toot

Page 59

Stitch

Sot the Machine

St_l;chwidth control 3 to 6

	Top thread	tension	_OO
			Stitch	length
	control 3 to	6
			control	yellow

stretchstitch position

Stretch Stitch

A:Zigzag toot

Sot the Machine

Stitch width contro_ 3 to 6

2

GD

Fop thread tension

control 3 to 8 Stitch length control orange

zone

2

Stretch Stitch

A: Zigzag toot

Choose this stitch to attach elastic to garments.

1.Mark the elastic into quarters and match these to the center front, center back and side seams.

2.Place the middle of the elastic under the center of the presser foot and stitch into place, making sure the elastlc is evenfy distrt* bu ted,

Use this stitch to join heavy weight interlining,

Overlap two raw edges together and use this stitch to join them.

57

Image 59

Contents Sewing Machine Kenmore Sewing Machine Sears Canada NCTable of Contents Portable Case or Cabinet is Available Know Your MachinePage Bobbin OFF Plug in the Machine and Switch on the PowerMachine is running Pressure Dial should Reset atFoot = Setting Spool Pins= Adjust the Presser Foot Lever = Thread CutterTo remove = Free-Arm Sewing the Removable Extension TableOranycirculargarmentarea Orareasofwearinchildrensclothes Etc Changethe Presser Foot To AttachZigzag Foot To Snap OnPresserFoot Types Guide Sliding Buttonhole FootUse this Zipper EdgesQu liter FabNcs Check Your Needle = Presser Foot TypesButtonhole Foot TopstitchingTo Change Your Needle Pin With Thread Winding Direction = To Remove the Bobbin from the Machine = Wind the BobbinPut OntoInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Toward Inches Pick Up Your Bobbin ThreadTop Adjust the Top Thread TensionIs up Indicator panelTop tension Too Tight Too Loose Is setStremh Stitch Needle position = Three Needle PositionWidth PositionThree Needle Position Sem Refer to 52 ~ Check ChartII1 III On pStitch Shell 3N6On p.15 Stitch Refer to OnpOn p 155 ZoneCheck Turn a Square Corner Thread tension Use the Darning PlateUse the darning plate in the following ways Control 0 grogCenter Out Control orangeControl 2 to Plate and replace foot holder and foot When you finish darning, remove the darningHeresHow Contro I to Basle Zigzag Set the MachineContro 3 to Pressure dial2 Applique= Bar Tacking Very shortEmbroidery Zigzag foot Darning plate Sew a Button=dth control Stitch length Control = Rick-Rack StretchStitch width control 5 to Three-Step ZigzagZi£rzegfoot Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Sat the MachineSet the Machine Stitch width Control Light WeightIlili!!ii!iiilji Or where = Learningto Sew ButtonholesHave CuffsControt 2 to Stitch wdthControl 3 to 31controtPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Control 3 to 8Stitch Iength control orange zone Set the Machine Stitch widthLingerie Control 3 to 6 2 SmockingZigzag foot Zigzag toot Stlchwidth control 3 toIii¸!iiiiii¸...........i Positron Stitch width control 3 toStitch length controt Satin stitch Contro greenWhatto do when Improper IncorrectInsert Cover plate by VacuumDriver Parts List 655t B868102403202 813404013Buttonhole Making 4551 Opener Template 6566 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable 1920Zipper Application 5253 Foot T2, 26 6566 Two-point BoxStitch Selector SettingupyourmachinePage FAGOT,NG Practical Stitch ChartYear WarrantyVisit Sewing Machine385