Sears 385. 1884180 owner manual Contro green, Satin stitch

Page 62

Set the Machirt_

Stitchw_dth

control 3 to 6

I

Top thread tension control 3 to8

co

Stitch length

contro_ green

ZOn_

F:Satin stitch

foot	Stretch Stitch

The Stitches and The,r Uses

These stitches are pu rely decorative.

You can sew one row or severa[ or vary the stitch width and length for

special effects.

Experiment on a scrap of fabric to see what spemal effects are possible.

Here's How

1. Adjust the stitch width and length as you desire.

2.Practice the stitch on a scrap of fabric.

3.Mark the lines for decoration on the fabric, using a washable fabric marker.

4.Lower the needle at the starting point.

5.Lower the presser foot.

6.Gentty guide the fabric atong the maked line.

6O

Image 62

Contents Sewing Machine Sears Canada NC Kenmore Sewing MachineTable of Contents Know Your Machine Portable Case or Cabinet is AvailablePage Bobbin Plug in the Machine and Switch on the Power OFFPressure Dial should Reset at Machine is running= Thread Cutter = Setting Spool Pins= Adjust the Presser Foot Lever Foot= Free-Arm Sewing the Removable Extension Table To removeOranycirculargarmentarea Orareasofwearinchildrensclothes Etc To Attach Changethe Presser FootZigzag Foot To Snap OnPresserFoot Types Zipper Edges Sliding Buttonhole FootUse this GuideQu liter Topstitching = Presser Foot TypesButtonhole Foot FabNcs Check Your NeedleTo Change Your Needle Onto = To Remove the Bobbin from the Machine = Wind the BobbinPut Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Pick Up Your Bobbin Thread Toward InchesAdjust the Top Thread Tension TopIs set Indicator panelTop tension Too Tight Too Loose Is upStremh Stitch Position = Three Needle PositionWidth Needle positionThree Needle Position Sem On p Check ChartII1 III Refer to 52 ~3N6 Stitch ShellOn p.15 Onp Stitch Refer toOn p 155 ZoneCheck Turn a Square Corner Control 0 grog Use the Darning PlateUse the darning plate in the following ways Thread tensionCenter Out Control orangeControl 2 to Plate and replace foot holder and foot When you finish darning, remove the darningHeresHow Basle Zigzag Set the Machine Contro I toContro 3 to Very short Applique= Bar Tacking Pressure dial2Embroidery Zigzag foot Darning plate Sew a Button=dth control = Rick-Rack Stretch Stitch length ControlThree-Step Zigzag Stitch width control 5 toSat the Machine Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Zi£rzegfootWeight Set the Machine Stitch width Control LightIlili!!ii!iiilji Cuffs = Learningto Sew ButtonholesHave Or where31controt Stitch wdthControl 3 to Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Control 3 to 8Stitch Iength control orange zone Set the Machine Stitch widthLingerie Smocking Control 3 to 6 2Zigzag foot Stlchwidth control 3 to Zigzag tootIii¸!iiiiii¸...........i Positron Stitch width control 3 toStitch length controt Contro green Satin stitchWhatto do when Improper IncorrectInsert Vacuum Cover plate byDriver Parts List 813404013 B868102403202 655t1920 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable Buttonhole Making 4551 Opener Template 6566Two-point Box Zipper Application 5253 Foot T2, 26 6566Settingupyourmachine Stitch SelectorPage Practical Stitch Chart FAGOT,NGWarranty YearVisit Sewing Machine385