Sears 385. 1884180 owner manual Openthezipper Cosethe zipper and turn

Page 55

8,

Openthezipper.

10.C_osethe zipper and turn the

1,

Remove

 

the

zipper

foot

and

9,

Lowerthepresserfootandstitch

fabric top side up.

 

attach

the

presser

bar

to the

left

 

 

 

 

therestof theseam,

 

 

pins

on

the

zipper

foot.

 

 

 

 

 

12.

Stitch

 

across

and

below

the

bot-

 

 

 

 

tom

of

the

zipper.

 

 

 

13. Turn the corner and continue to guide the foot along the zipper teeth, as shown,

Stitch through the fabric and zipper tape.

14+ Stop about 2" from the top of the z_pper.

15.Lower the needle into the fabric and raise the presser foot,

16, Remove the basting stitches and open the zipper.

17.Lower the foot and stttch the rest of the seam. Make sure the'fold is even.

53

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Sewing Machine Kenmore Sewing Machine Sears Canada NCTable of Contents Portable Case or Cabinet is Available Know Your MachinePage Bobbin OFF Plug in the Machine and Switch on the PowerMachine is running Pressure Dial should Reset atFoot = Setting Spool Pins= Adjust the Presser Foot Lever = Thread CutterTo remove = Free-Arm Sewing the Removable Extension TableOranycirculargarmentarea Orareasofwearinchildrensclothes Etc Changethe Presser Foot To AttachPresserFoot Types To Snap OnZigzag Foot Guide Sliding Buttonhole FootUse this Zipper EdgesQu liter FabNcs Check Your Needle = Presser Foot TypesButtonhole Foot TopstitchingTo Change Your Needle Pin With Thread Winding Direction = To Remove the Bobbin from the Machine = Wind the BobbinPut OntoInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Toward Inches Pick Up Your Bobbin ThreadTop Adjust the Top Thread TensionIs up Indicator panelTop tension Too Tight Too Loose Is setStremh Stitch Needle position = Three Needle PositionWidth PositionThree Needle Position Sem Refer to 52 ~ Check ChartII1 III On pStitch Shell 3N6On p.15 Stitch Refer to OnpCheck ZoneOn p 155 Turn a Square Corner Thread tension Use the Darning PlateUse the darning plate in the following ways Control 0 grogControl 2 to Control orangeCenter Out HeresHow When you finish darning, remove the darningPlate and replace foot holder and foot Contro I to Basle Zigzag Set the MachineContro 3 to Pressure dial2 Applique= Bar Tacking Very shortEmbroidery =dth control Sew a ButtonZigzag foot Darning plate Stitch length Control = Rick-Rack StretchStitch width control 5 to Three-Step ZigzagZi£rzegfoot Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Sat the MachineSet the Machine Stitch width Control Light WeightIlili!!ii!iiilji Or where = Learningto Sew ButtonholesHave CuffsControt 2 to Stitch wdthControl 3 to 31controtPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Lingerie Set the Machine Stitch widthControl 3 to 8Stitch Iength control orange zone Control 3 to 6 2 SmockingZigzag foot Zigzag toot Stlchwidth control 3 toIii¸!iiiiii¸...........i Stitch length controt Stitch width control 3 toPositron Satin stitch Contro greenWhatto do when Insert IncorrectImproper Cover plate by VacuumDriver Parts List 655t B868102403202 813404013Buttonhole Making 4551 Opener Template 6566 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable 1920Zipper Application 5253 Foot T2, 26 6566 Two-point BoxStitch Selector SettingupyourmachinePage FAGOT,NG Practical Stitch ChartYear Warranty385 Sewing MachineVisit
Top Page Image Contents