Sears 385. 1884180 owner manual Stremh Stitch

Page 24

V Length

Stremh Stitch

The stitch length controt regulates the length of stitch, and also has a stretch stitches setting.

The higher the number, the longer the stitch.

0 means no feed.

To select Stretch Stitches, set this control at Stretch Stitch.

NOTE : When you select decorative stitches (green) or built-in buttonhole (blue), make sure that you do not set the stitch length control at

"Stretch Stitch".

Study the orange, green, yeIlow and blue section around this

control. These are recommended zones of stitch length and color- coded to the stitches pictured on the stitch indicator panel.

{n stretch stitch sewing, the stretch stitch

adjuster should usually be in a neutral

position (between "+'" and "-"or

position), When sewing some fabrics, you

may need to adjust this controt to balance the stitches for appearance sake.

If design seems open like the illustrations to the left, adjust the control slightly

toward "'-"until design looks like the center design.

If the design appears to be c_osed as in

the right hand illustrations, turn the

conllol toward "'+" until stitching _s as you desire.

22

Image 24

Contents Sewing Machine Sears Canada NC Kenmore Sewing MachineTable of Contents Know Your Machine Portable Case or Cabinet is AvailablePage Bobbin Plug in the Machine and Switch on the Power OFFPressure Dial should Reset at Machine is running= Setting Spool Pins = Adjust the Presser Foot Lever= Thread Cutter Foot= Free-Arm Sewing the Removable Extension Table To removeOranycirculargarmentarea Orareasofwearinchildrensclothes Etc To Attach Changethe Presser FootTo Snap On PresserFoot TypesZigzag Foot Sliding Buttonhole Foot Use thisZipper Edges GuideQu liter = Presser Foot Types Buttonhole FootTopstitching FabNcs Check Your NeedleTo Change Your Needle = To Remove the Bobbin from the Machine = Wind the Bobbin PutOnto Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Pick Up Your Bobbin Thread Toward InchesAdjust the Top Thread Tension TopIndicator panel Top tension Too Tight Too LooseIs set Is upStremh Stitch = Three Needle Position WidthPosition Needle positionThree Needle Position Sem Check Chart II1 IIIOn p Refer to 52 ~3N6 Stitch ShellOn p.15 Onp Stitch Refer toZone CheckOn p 155 Turn a Square Corner Use the Darning Plate Use the darning plate in the following waysControl 0 grog Thread tensionControl orange Control 2 toCenter Out When you finish darning, remove the darning HeresHowPlate and replace foot holder and foot Basle Zigzag Set the Machine Contro I toContro 3 to Applique = Bar TackingVery short Pressure dial2Embroidery Sew a Button =dth controlZigzag foot Darning plate = Rick-Rack Stretch Stitch length ControlThree-Step Zigzag Stitch width control 5 toOvercast Stretch Stitching Sarging or Pine Leaf Stretch StitchinSat the Machine Zi£rzegfootWeight Set the Machine Stitch width Control LightIlili!!ii!iiilji = Learningto Sew Buttonholes HaveCuffs Or whereStitch wdth Control 3 to31controt Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Set the Machine Stitch width LingerieControl 3 to 8Stitch Iength control orange zone Smocking Control 3 to 6 2Zigzag foot Stlchwidth control 3 to Zigzag tootIii¸!iiiiii¸...........i Stitch width control 3 to Stitch length controtPositron Contro green Satin stitchWhatto do when Incorrect InsertImproper Vacuum Cover plate byDriver Parts List B868 102403202813404013 655tOveredge foot 13, 27, 40, 42 Parts list 6566 Performance Plug connector Portable1920 Buttonhole Making 4551 Opener Template 6566Two-point Box Zipper Application 5253 Foot T2, 26 6566Settingupyourmachine Stitch SelectorPage Practical Stitch Chart FAGOT,NGWarranty YearSewing Machine 385Visit