Sears 385. 1884180 owner manual Plug in the Machine and Switch on the Power, Off

Page 7

Plug in the Machine and Switch on the Power

Power supply plug	Power
	Power
	/ supply

Plug connector

Machine plug

NOTE: Before inserting the plug into your

machine, be sure the power switch is

OFF

t.Check your outlet to be sure it is a 110to 120 Volt AC outlet,

2.Insert the machine plug into the three-prong outlet, as shown, tt will only fit one way.

3.Insert the power supply plug into the outlet.

Sewing ligh_

_

Power sw_Ich

.J

4.Push the light and power switch to turn on the power and sewing light,

SAFETY FEATURE:

Your machine witl not operate unless the

llght/power switch _s turned on, If you are

interrupted or stop sewing, turn off the

light/power switch to prevent mllury to children.

Foot Control Use

J

The toot control regulates the speed at which you sew.

To increase speed, gently press down with the ball of your foot.

To decrease speed, release your foot pres- sure slightly.

NOTE: The foot control is sensitive and

will increase or decrease your

sewing speed immediately. Practice on a scrap of fabric to

regulate your sewing speed to your taste and needs.

Image 7

Contents Sewing Machine Kenmore Sewing Machine Sears Canada NCTable of Contents Portable Case or Cabinet is Available Know Your MachinePage Bobbin OFF Plug in the Machine and Switch on the PowerMachine is running Pressure Dial should Reset atFoot = Setting Spool Pins= Adjust the Presser Foot Lever = Thread CutterTo remove = Free-Arm Sewing the Removable Extension TableOranycirculargarmentarea Orareasofwearinchildrensclothes Etc Changethe Presser Foot To AttachPresserFoot Types To Snap OnZigzag Foot Guide Sliding Buttonhole FootUse this Zipper EdgesQu liter FabNcs Check Your Needle = Presser Foot TypesButtonhole Foot TopstitchingTo Change Your Needle Pin With Thread Winding Direction = To Remove the Bobbin from the Machine = Wind the BobbinPut OntoInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Toward Inches Pick Up Your Bobbin ThreadTop Adjust the Top Thread TensionIs up Indicator panelTop tension Too Tight Too Loose Is setStremh Stitch Needle position = Three Needle PositionWidth PositionThree Needle Position Sem Refer to 52 ~ Check ChartII1 III On pStitch Shell 3N6On p.15 Stitch Refer to OnpCheck ZoneOn p 155 Turn a Square Corner Thread tension Use the Darning PlateUse the darning plate in the following ways Control 0 grogControl 2 to Control orangeCenter Out HeresHow When you finish darning, remove the darningPlate and replace foot holder and foot Contro I to Basle Zigzag Set the MachineContro 3 to Pressure dial2 Applique= Bar Tacking Very shortEmbroidery =dth control Sew a ButtonZigzag foot Darning plate Stitch length Control = Rick-Rack StretchStitch width control 5 to Three-Step ZigzagZi£rzegfoot Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Sat the MachineSet the Machine Stitch width Control Light WeightIlili!!ii!iiilji Or where = Learningto Sew ButtonholesHave CuffsControt 2 to Stitch wdthControl 3 to 31controtPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Lingerie Set the Machine Stitch widthControl 3 to 8Stitch Iength control orange zone Control 3 to 6 2 SmockingZigzag foot Zigzag toot Stlchwidth control 3 toIii¸!iiiiii¸...........i Stitch length controt Stitch width control 3 toPositron Satin stitch Contro greenWhatto do when Insert IncorrectImproper Cover plate by VacuumDriver Parts List 655t B868102403202 813404013Buttonhole Making 4551 Opener Template 6566 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable 1920Zipper Application 5253 Foot T2, 26 6566 Two-point BoxStitch Selector SettingupyourmachinePage FAGOT,NG Practical Stitch ChartYear Warranty385 Sewing MachineVisit