Sears 385. 1884180 owner manual Set the Machine, Pins a Lever

Page 51

Set the Machine

Stitch w_dth

a_

Top thread tension control 2 to 6

Stitch length control 4

2

Stretch Stitch

Buttonhole toot

Helpful Hints

You can obtain best results to use #60 _ #80 light weight threads as bobbin thread.

NOTE: It is advisable to use a blue

stretch fabric needle when

sewing knits and synthetic fabrics.

Pins (A)

Lever

TolRound

thread

	v	Base ptate
		Hook
Rectangular	hole

a.Remove the extension table.

b.Raise the needle to its highest position.

c. Remove the foot holder.

d, Pull bobbin thread out about 3" straight back toward rear of machine.

e.Insert hook of base plate into rectangular hole of needle plate°

f.Pull lever back to align the hook with the rectangular hole.

g.Snap base p_ate down to fit two pins (A) at the back of base plate into two round holes (B) on needle plate.

Release tever,

4g

Image 51

Contents Sewing Machine Kenmore Sewing Machine Sears Canada NCTable of Contents Portable Case or Cabinet is Available Know Your MachinePage Bobbin OFF Plug in the Machine and Switch on the PowerMachine is running Pressure Dial should Reset atFoot = Setting Spool Pins= Adjust the Presser Foot Lever = Thread CutterTo remove = Free-Arm Sewing the Removable Extension TableOranycirculargarmentarea Orareasofwearinchildrensclothes Etc Changethe Presser Foot To AttachTo Snap On PresserFoot TypesZigzag Foot Guide Sliding Buttonhole FootUse this Zipper EdgesQu liter FabNcs Check Your Needle = Presser Foot TypesButtonhole Foot TopstitchingTo Change Your Needle Pin With Thread Winding Direction = To Remove the Bobbin from the Machine = Wind the BobbinPut OntoInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Toward Inches Pick Up Your Bobbin ThreadTop Adjust the Top Thread TensionIs up Indicator panelTop tension Too Tight Too Loose Is setStremh Stitch Needle position = Three Needle PositionWidth PositionThree Needle Position Sem Refer to 52 ~ Check ChartII1 III On pStitch Shell 3N6On p.15 Stitch Refer to OnpZone CheckOn p 155 Turn a Square Corner Thread tension Use the Darning PlateUse the darning plate in the following ways Control 0 grogControl orange Control 2 toCenter Out When you finish darning, remove the darning HeresHowPlate and replace foot holder and foot Contro I to Basle Zigzag Set the MachineContro 3 to Pressure dial2 Applique= Bar Tacking Very shortEmbroidery Sew a Button =dth controlZigzag foot Darning plate Stitch length Control = Rick-Rack StretchStitch width control 5 to Three-Step ZigzagZi£rzegfoot Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Sat the MachineSet the Machine Stitch width Control Light WeightIlili!!ii!iiilji Or where = Learningto Sew ButtonholesHave CuffsControt 2 to Stitch wdthControl 3 to 31controtPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Set the Machine Stitch width LingerieControl 3 to 8Stitch Iength control orange zone Control 3 to 6 2 SmockingZigzag foot Zigzag toot Stlchwidth control 3 toIii¸!iiiiii¸...........i Stitch width control 3 to Stitch length controtPositron Satin stitch Contro greenWhatto do when Incorrect InsertImproper Cover plate by VacuumDriver Parts List 655t B868102403202 813404013Buttonhole Making 4551 Opener Template 6566 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable 1920Zipper Application 5253 Foot T2, 26 6566 Two-point BoxStitch Selector SettingupyourmachinePage FAGOT,NG Practical Stitch ChartYear WarrantySewing Machine 385Visit