Sears 385. 1884180 owner manual Driver

Page 66

1.Unplug the machine and remove the presser foot and needle.

2.Remove the bobbin face cover plate.

3.Remove the screw on the teft side

of the needle w_th the large screw

driver.

4.Remove the needle plate.

6, Use the lint brush to clean the feed dogs, hook race and bobbin

holder. Also use a soft, dry c1oth,

Open face cover plate and oil points as shown below at least once a year. On or two drops of oil is sufficient.

Remove excess oil, otherwise it may stain fabrics,

5.Take out the bobbin. Lift up the bobbin holder and remove _t,

In case machine is not used for an

extended time, oll it before sewing. Use good quality sewing machine oil.

No other oiling is required

Above points are only area which require oiling on this machine,

Line up the red marks and place the bobbin holder so the knob fits next to the stopper in the hook race, as shown above.

64

Image 66

Contents Sewing Machine Sears Canada NC Kenmore Sewing MachineTable of Contents Know Your Machine Portable Case or Cabinet is AvailablePage Bobbin Plug in the Machine and Switch on the Power OFFPressure Dial should Reset at Machine is running= Thread Cutter = Setting Spool Pins= Adjust the Presser Foot Lever Foot= Free-Arm Sewing the Removable Extension Table To removeOranycirculargarmentarea Orareasofwearinchildrensclothes Etc To Attach Changethe Presser FootTo Snap On PresserFoot TypesZigzag Foot Zipper Edges Sliding Buttonhole FootUse this GuideQu liter Topstitching = Presser Foot TypesButtonhole Foot FabNcs Check Your NeedleTo Change Your Needle Onto = To Remove the Bobbin from the Machine = Wind the BobbinPut Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Pick Up Your Bobbin Thread Toward InchesAdjust the Top Thread Tension TopIs set Indicator panelTop tension Too Tight Too Loose Is upStremh Stitch Position = Three Needle PositionWidth Needle positionThree Needle Position Sem On p Check ChartII1 III Refer to 52 ~3N6 Stitch ShellOn p.15 Onp Stitch Refer toZone CheckOn p 155 Turn a Square Corner Control 0 grog Use the Darning PlateUse the darning plate in the following ways Thread tensionControl orange Control 2 toCenter Out When you finish darning, remove the darning HeresHowPlate and replace foot holder and foot Basle Zigzag Set the Machine Contro I toContro 3 to Very short Applique= Bar Tacking Pressure dial2Embroidery Sew a Button =dth controlZigzag foot Darning plate = Rick-Rack Stretch Stitch length ControlThree-Step Zigzag Stitch width control 5 toSat the Machine Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Zi£rzegfootWeight Set the Machine Stitch width Control LightIlili!!ii!iiilji Cuffs = Learningto Sew ButtonholesHave Or where31controt Stitch wdthControl 3 to Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Set the Machine Stitch width LingerieControl 3 to 8Stitch Iength control orange zone Smocking Control 3 to 6 2Zigzag foot Stlchwidth control 3 to Zigzag tootIii¸!iiiiii¸...........i Stitch width control 3 to Stitch length controtPositron Contro green Satin stitchWhatto do when Incorrect InsertImproper Vacuum Cover plate byDriver Parts List 813404013 B868102403202 655t1920 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable Buttonhole Making 4551 Opener Template 6566Two-point Box Zipper Application 5253 Foot T2, 26 6566Settingupyourmachine Stitch SelectorPage Practical Stitch Chart FAGOT,NGWarranty YearSewing Machine 385Visit