Sears 385. 1884180 owner manual Set the Machine Stitch width Control Light, Weight

Page 45

		Set the Machine
		Stitch width			I/4"
		control		2 to :3	I/4"
		2	3	#
		0		_
				Light		'L,JWhen the
				Weight		_,I	needle
				Fabric	t/4"	,'_	comes
Fop thread	tension					_;	to the
Fop thread	tension
control 2 to	6	Stitch	length
		Stitch	length
		control		orange
		zone		Heavy
				Heavy

2	Weight
	Fabric

Blind Hem Stitch Foot G

1.Finish the raw edge of your hem any way you desire. (See overcasting page 40).

Stretch Stitch	2. Measure,		turn	up your	hem and pin,
	NOTE:	For	light	weight	fabrics, you may need a double fold.

3.Fold the material (bottom side out) on the edge to be stitched, as shown, leaving 1/4" of the finished hem edge showing.

4.Place garment under presser foot in such a manner that straight stitches wilt be sewn on extended edge. The zigzag stitch should just catch the fold of the garment.

5.After hemming, press both sides of the finished hem. The top side of the garment will show only the blind stitches.

43

Image 45

Contents Sewing Machine Kenmore Sewing Machine Sears Canada NCTable of Contents Portable Case or Cabinet is Available Know Your MachinePage Bobbin OFF Plug in the Machine and Switch on the PowerMachine is running Pressure Dial should Reset at= Adjust the Presser Foot Lever = Setting Spool Pins= Thread Cutter FootTo remove = Free-Arm Sewing the Removable Extension TableOranycirculargarmentarea Orareasofwearinchildrensclothes Etc Changethe Presser Foot To AttachTo Snap On PresserFoot TypesZigzag Foot Use this Sliding Buttonhole FootZipper Edges GuideQu liter Buttonhole Foot = Presser Foot TypesTopstitching FabNcs Check Your NeedleTo Change Your Needle Put = To Remove the Bobbin from the Machine = Wind the BobbinOnto Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Toward Inches Pick Up Your Bobbin ThreadTop Adjust the Top Thread TensionTop tension Too Tight Too Loose Indicator panelIs set Is upStremh Stitch Width = Three Needle PositionPosition Needle positionThree Needle Position Sem II1 III Check ChartOn p Refer to 52 ~Stitch Shell 3N6On p.15 Stitch Refer to OnpZone CheckOn p 155 Turn a Square Corner Use the darning plate in the following ways Use the Darning PlateControl 0 grog Thread tensionControl orange Control 2 toCenter Out When you finish darning, remove the darning HeresHowPlate and replace foot holder and foot Contro I to Basle Zigzag Set the MachineContro 3 to = Bar Tacking AppliqueVery short Pressure dial2Embroidery Sew a Button =dth controlZigzag foot Darning plate Stitch length Control = Rick-Rack StretchStitch width control 5 to Three-Step ZigzagSarging or Pine Leaf Stretch Stitchin Overcast Stretch StitchingSat the Machine Zi£rzegfootSet the Machine Stitch width Control Light WeightIlili!!ii!iiilji Have = Learningto Sew ButtonholesCuffs Or whereControl 3 to Stitch wdth31controt Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Set the Machine Stitch width LingerieControl 3 to 8Stitch Iength control orange zone Control 3 to 6 2 SmockingZigzag foot Zigzag toot Stlchwidth control 3 toIii¸!iiiiii¸...........i Stitch width control 3 to Stitch length controtPositron Satin stitch Contro greenWhatto do when Incorrect InsertImproper Cover plate by VacuumDriver Parts List 102403202 B868813404013 655tPlug connector Portable Overedge foot 13, 27, 40, 42 Parts list 6566 Performance1920 Buttonhole Making 4551 Opener Template 6566Zipper Application 5253 Foot T2, 26 6566 Two-point BoxStitch Selector SettingupyourmachinePage FAGOT,NG Practical Stitch ChartYear WarrantySewing Machine 385Visit