Sears 385. 1884180 owner manual Applique, = Bar Tacking, Very short, Pressure dial2

Page 39

Applique

Set the Machine

Stitch width control 2 to 6

2

Top thread tens=on control 2 to 6

Stitch length controt 0.5 to 1

2

J

Baste ior fuse with iron-onfabric joiner) apptique pieces on the fabric.

Stitch around the applique making sure the needte falls along the outer edge of the applique,

=Bar Tacking

Set the Machine

Stitch wtdth

control 2 to 6

1

							;f
Top thread	tens=on	Stitch	length		]
control 2 to	6	Stitch	length
		control	0.5 to 1
			ThL5	stitch	is similar	to a	very short
			satin stitch and is used to reinforce
			points	of	strain such	as	corners	or
			pockets and straps on lingerie.

Stretch Stitch

F:Satin sttteh toot

Pressure dial:2

When sewing corners, lower the needle down into the fabric. Raise the presser

foot and pivot the fabric to the right or _eft.

Stretch Stitch

A: Zigzag foot

Sew 4 to 6 zigzag stitches,

37

Image 39

Contents Sewing Machine Kenmore Sewing Machine Sears Canada NCTable of Contents Portable Case or Cabinet is Available Know Your MachinePage Bobbin OFF Plug in the Machine and Switch on the PowerMachine is running Pressure Dial should Reset atFoot = Setting Spool Pins= Adjust the Presser Foot Lever = Thread CutterTo remove = Free-Arm Sewing the Removable Extension TableOranycirculargarmentarea Orareasofwearinchildrensclothes Etc Changethe Presser Foot To AttachTo Snap On PresserFoot TypesZigzag Foot Guide Sliding Buttonhole FootUse this Zipper EdgesQu liter FabNcs Check Your Needle = Presser Foot TypesButtonhole Foot TopstitchingTo Change Your Needle Pin With Thread Winding Direction = To Remove the Bobbin from the Machine = Wind the BobbinPut OntoInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Toward Inches Pick Up Your Bobbin ThreadTop Adjust the Top Thread TensionIs up Indicator panelTop tension Too Tight Too Loose Is setStremh Stitch Needle position = Three Needle PositionWidth PositionThree Needle Position Sem Refer to 52 ~ Check ChartII1 III On pStitch Shell 3N6On p.15 Stitch Refer to OnpZone CheckOn p 155 Turn a Square Corner Thread tension Use the Darning PlateUse the darning plate in the following ways Control 0 grogControl orange Control 2 toCenter Out When you finish darning, remove the darning HeresHowPlate and replace foot holder and foot Contro I to Basle Zigzag Set the MachineContro 3 to Pressure dial2 Applique= Bar Tacking Very shortEmbroidery Sew a Button =dth controlZigzag foot Darning plate Stitch length Control = Rick-Rack StretchStitch width control 5 to Three-Step ZigzagZi£rzegfoot Overcast Stretch StitchingSarging or Pine Leaf Stretch Stitchin Sat the MachineSet the Machine Stitch width Control Light WeightIlili!!ii!iiilji Or where = Learningto Sew ButtonholesHave CuffsControt 2 to Stitch wdthControl 3 to 31controtPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Set the Machine Stitch width LingerieControl 3 to 8Stitch Iength control orange zone Control 3 to 6 2 SmockingZigzag foot Zigzag toot Stlchwidth control 3 toIii¸!iiiiii¸...........i Stitch width control 3 to Stitch length controtPositron Satin stitch Contro greenWhatto do when Incorrect InsertImproper Cover plate by VacuumDriver Parts List 655t B868102403202 813404013Buttonhole Making 4551 Opener Template 6566 Overedge foot 13, 27, 40, 42 Parts list 6566 PerformancePlug connector Portable 1920Zipper Application 5253 Foot T2, 26 6566 Two-point BoxStitch Selector SettingupyourmachinePage FAGOT,NG Practical Stitch ChartYear WarrantySewing Machine 385Visit