Sears 385. 1884180 owner manual Set the Machine Stitch width, Lingerie

Page 56

Set the Machine

Stitch width control 3 to 6

2 3

::

:

::: :

;;

: ::

:;;;:

:

: :;}

; :

:.

:

Set the Machine

Stitch width

oe

Top thread	tension
eontro 4	to 9	Stitch	length
		control	orange

zone

Stretch Stitch

F:Satin stitch foot

_

J

The Stitch and Its Uses

The Shell Stitch is formed by sewing a

blind hem over forded fabric. Several rows of shell stitching are called shell tucks.

Shell stitching can be used to finish hems, sleeve and neck openings.

Sheii tucking can be used to create

scalloped tucks on blouses and

lingerie,

Here's How

1, For best effect:

-set the stitch length as you desire,

--you may need to tighten the

top thread tension slightly.

- a_low the needle to just clear the folded edge of the fabric when it zigzags.

2.If you sew rows of shell stitches, space the rows 5/8" apart.

You can sew Shell Stitch on knits or sort silky wovens in any direction.

Top thread tension

control 3 to 8Stitch Iength control orange zone

3,

Stretch Stitch

A: Zigzag foot

% .....

\

This stitch can also be used as a

single overlock stitch as well

54

Image 56

Contents Sewing Machine Sears Canada NC Kenmore Sewing MachineTable of Contents Know Your Machine Portable Case or Cabinet is AvailablePage Bobbin Plug in the Machine and Switch on the Power OFFPressure Dial should Reset at Machine is running= Setting Spool Pins = Adjust the Presser Foot Lever= Thread Cutter Foot= Free-Arm Sewing the Removable Extension Table To removeOranycirculargarmentarea Orareasofwearinchildrensclothes Etc To Attach Changethe Presser FootZigzag Foot To Snap OnPresserFoot Types Sliding Buttonhole Foot Use thisZipper Edges GuideQu liter = Presser Foot Types Buttonhole FootTopstitching FabNcs Check Your NeedleTo Change Your Needle = To Remove the Bobbin from the Machine = Wind the Bobbin PutOnto Pin With Thread Winding DirectionInsertthe Bobbin into the Bobbin Hotder Thread Your Needle Pick Up Your Bobbin Thread Toward InchesAdjust the Top Thread Tension TopIndicator panel Top tension Too Tight Too LooseIs set Is upStremh Stitch = Three Needle Position WidthPosition Needle positionThree Needle Position Sem Check Chart II1 IIIOn p Refer to 52 ~3N6 Stitch ShellOn p.15 Onp Stitch Refer toOn p 155 ZoneCheck Turn a Square Corner Use the Darning Plate Use the darning plate in the following waysControl 0 grog Thread tensionCenter Out Control orangeControl 2 to Plate and replace foot holder and foot When you finish darning, remove the darningHeresHow Basle Zigzag Set the Machine Contro I toContro 3 to Applique = Bar TackingVery short Pressure dial2Embroidery Zigzag foot Darning plate Sew a Button=dth control = Rick-Rack Stretch Stitch length ControlThree-Step Zigzag Stitch width control 5 toOvercast Stretch Stitching Sarging or Pine Leaf Stretch StitchinSat the Machine Zi£rzegfootWeight Set the Machine Stitch width Control LightIlili!!ii!iiilji = Learningto Sew Buttonholes HaveCuffs Or whereStitch wdth Control 3 to31controt Controt 2 toPage Buttonhole foot Pins a Lever Buttonhole Marked buttonhole End ol opemng Openthezipper Cosethe zipper and turn Control 3 to 8Stitch Iength control orange zone Set the Machine Stitch widthLingerie Smocking Control 3 to 6 2Zigzag foot Stlchwidth control 3 to Zigzag tootIii¸!iiiiii¸...........i Positron Stitch width control 3 toStitch length controt Contro green Satin stitchWhatto do when Improper IncorrectInsert Vacuum Cover plate byDriver Parts List B868 102403202813404013 655tOveredge foot 13, 27, 40, 42 Parts list 6566 Performance Plug connector Portable1920 Buttonhole Making 4551 Opener Template 6566Two-point Box Zipper Application 5253 Foot T2, 26 6566Settingupyourmachine Stitch SelectorPage Practical Stitch Chart FAGOT,NGWarranty YearVisit Sewing Machine385