Dimplex EN55014, EN60555-2 Cleaning, Water tank, Sump, Air filter, Recycling, After Sales Service

Cleaning.

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE STOVE.

We Recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-

Water Tank, Sump and Seal, Sump lid, Tank cap and seal, Air filter.

For general cleaning use a soft clean duster – never use abrasive cleaners. To remove any accumulation of dust or fluff the soft brush attachment of a vacuum cleaner should occasionally be used to clean the outlet grille of the fan stove.

Water tank

1.Remove water tank, as described earlier, put into sink and empty water.

2.Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in the outer groove and the centre rubber seal.

3.Put a small quantity of washing up liquid into the tank, refit the cap and shake well, rinse out until all traces of washing up liquid are gone.

4.Refill with filtered tap water only, replace the cap, do not overtighten.

Sump

1.Press Switch ‘A’ to the ‘OFF’ (0) position

2.Gently pull the drawer out as far as possible. (See Fig. 3)

3.Remove the water tank by lifting upwards.

4.Disconnect the electrical connector, located on the left side of the sump, by first loosening the two retaining screws and gently withdrawing the connector. (See Fig. 8)

5.Release the lower sump locking tabs by turning 90°, this allows the sump to be lifted completely from its location. (See Fig. 9)

6.Gently lift up the sump assembly, taking care to keep level so as not to spill any water. Sit the assembly in the sink. (See Fig. 10)

7.Release the two upper sump locking tabs by turning 90°, then lift off the sump lid. (See Fig. 11)

8.Carefully tilt, as shown, so that the liquid drains out of the sump. (See Fig. 12)

9.Put a small amount of washing up liquid into the sump, and using the supplied brush, gently clean all surfaces including the metal discs and the rubber seal located in the top grooved surface. Do not remove the rubber seals. (See Fig. 13 and 14)

10.When cleaned, thoroughly rinse the sump with clean water.

11.Clean the outlet surface of the sump lid with the brush and flush out thoroughly with water. (See Fig. 15 & 16)

12.Reverse the above steps to reassemble.

Air filter.

1.Press Switch ‘A’ to the ‘OFF’ (0) position (See Fig. 2)

2.Gently pull the drawer out as far as possible. (See Fig. 3)

3.Remove the tank and place in a sink with the cap facing upwards.

4.Gently slide upwards the air filter plastic holder. (See Fig. 17)

5.Remove the filter combination from the plastic holder.

6.Gently rinse with water in the sink and dry with fabric towel before returning.

7.Replace the filter combination making sure that the course black filter is in contact with the plastic holder. (See Fig. 18)

8.Replace the tank.

9.Close the drawer fully.

10.Press Switch ‘A’ to the ‘ON’ ( I ) position (See Fig. 2)

Recycling.

For electrical products sold within the European Community. At the end of the electrical products useful life it should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.

After Sales Service.

Your product is guaranteed for one year from the date of purchase. Within this period, we undertake to repair or exchange this product free of charge (excluding lamps

&subject to availability) provided it has been installed and operated in accordance with these instructions. Should you require after sales service or should you need to purchase any spares, please contact the retailer from whom the appliance was purchased or contact the service number relevant to your country on the warranty card. Please do not return a faulty product to us in the first instance as this may result in the loss or damage and delay in providing you with a satisfactory service.

Please retain your receipt as proof of purchase.

- 4 -