Cornelius 000, 10 installation manual Cleaning CO2 System GAS Check Valves, Syrup Flavor Change

Page 37

6.Open (counterclockwise) CO2 cylinder valve slightly to allow lines to slowly fill with gas, then open valve fully to back-seat valve. (Back-seating valve prevents leakage around valve shaft.)

REPLENISHING SYRUP SUPPLY

NOTE: The following instructions are applicable only when replenishing same flavor syrup. Refer to SYRUP FLAVOR CHANGE when changing syrup flavor.

1.Disconnect empty soft drink tank from syrup system.

2.Check soft drink tank quick disconnects for sticky or restricted operation. Wash disconnects in warm water.

3.Connect full tank of syrup into syrup system.

SYRUP FLAVOR CHANGE

1.Perform sanitizing procedure on syrup system syrup flavor change will be made on.

2.Check soft drink tank quick disconnects for sticky or restricted operation. Wash disconnects in warm water.

3.Connect full tank of new flavor syrup into syrup system.

FIGURE 10. CO2 GAS CHECK VALVE

CLEANING CO2 SYSTEM GAS CHECK VALVES

SECONDARY CO2 REGULATORS AND CO2 MANIFOLD CO2 GAS CHECK VALVES

(see Figures 2 and 10)

The secondary CO2 regulators and CO2 manifold CO2 gas check valves must be inspected and serviced at least once a year under normal conditions and after any servicing or disruption of the CO2 system.

ALWAYS REPLACE QUAD RING SEAL EACH TIME GAS CHECK VALVES ARE SERVICED.

CARBONATORS CO2 INLET LINES CO2 GAS CHECK VALVE

(see Figures 2 and 10)

Carbonators CO2 inlet lines CO2 gas check valve, located inside Cooling Unit, must be inspected and serviced at least once a year under normal conditions and after any servicing or disruption of the CO2 system. ALWAYS INSTALL NEW BALL SEAT (QUAD RING) P/N 312418000 EACH TIME CHECK VALVE IS SERVICED.

CONNECTING EXTERNAL CARBONATOR TO COOLING UNIT

An external carbonator may be connected to the Cooling Unit (see Figure 2) for a larger supply of carbonated water.

300381000

32

Page 36 Page 38
Image 37
Page 36 Page 38
Contents This Document Contains Important Information AURORAR10,000 Cooling UnitTable of Contents Table of Contents cont’d Table of Contents cont’d LOOSE-SHIPPED Parts Cooling Unit Description General DescriptionCooling Unit Model Numbers Design DataRemote Condenser Coil and FAN ASS’Y Data P/N System Theory of OperationFlow Diagram Typical Installation Identification of LOOSE-SHIPPED Parts Unpacking and InspectionSelecting Location Cooling UnitRemote Condenser Coil and FAN ASS’Y if Applicable Installing Cooling UnitPlacing Cooling Unit in Location 24VAC Power Transformer Connecting Electrical Power Circuit to Cooling UnitCooling Unit factory warranty Connecting CO2 Inlet Supply Line to Cooling Unit Connecting Plain Water Inlet Supply Line to Cooling UnitCooling Unit Space Required Placing Cooling Unit in Operating PositionOperation Preparing Cooling Unit for OperationStarting Carbonated Water Circulating Pump Starting Cooling Unit Refrigeration SystemActivating Syrup Systems Installing Line Identification Label Dispensing Station AdjustmentsAdjusting Water Flow Rate Leak Check and Insulating Cooling Unit Outlet LinesThis page Left Blank Intentionally Cooling Unit Carbonator Motor Switch Cooling Unit Refrigeration Power SwitchCooling Unit Circulating Motor Switch Operating ControlsAdjustments Cooling Unit Maintenance Cleaning and SanitizingCleaning CO2 GAS Check Valves Periodic Inspection Preparing Cooling Unit for SHIPPING, STORING, or RelocatingCleaning Condenser Coil Periodic CleaningChecking ICE Water Bath Changing ICE Water Bath FAN Assembly Item 4 300381000 Carbonator Liquid Level Control Switches Primary CO2 Regulator Carbonated Water Circulating Pump Motor LubricationIndex Part Name Secondary CO2 RegulatorsDaily Cleaning of Unit Adjusting Carbonators Tanks Liquid LevelsWater Flow Rate Wash Syrup Systems Sanitizing POST-MIX Syrup SystemsFlush Syrup Systems Water Flush Syrup Systems Sanitize Syrup SystemsPurge Water OUT of Syrup Systems Restore Operation Connecting External Carbonator to Cooling Unit Cleaning CO2 System GAS Check ValvesSyrup Flavor Change Carbonators CO2 Inlet Lines CO2 GAS Check Valve300381000 300381000 Wiring Diagram LOW-VOLTAGE System Model Number Wiring Diagram HIGH-VOLTAGE System This page Left Blank Intentionally Dispensed Drink TOO WATER-TO-SYRUP ‘RATIO’LOW or TOO High Carbonation TOO LOW Dispensed ProductComes OUT Dispensing Valve Clear But Foams in CUP Only Carbonated Water aDispensed CONT’D Only Carbonated WaterOnly Syrup Dispensed Carbonator MotorsErratic Cycling Operate Refrigeration PowerCarbonator Water Pump MotorOperate CONT’D Temperature SensingRefrigeration System Device and HIGH-PRESSURECommpressor Operates Bank CONT’D Refrigeration Flow DiagramContinuousls but does Not Form Sufficient ICEWarranty Page One Cornelius Place Anoka, Minnesota 612 800
Related manuals
Manual 42 pages 12.14 Kb

000, 10 specifications

Cornelius 10,000 PLUS is a pioneering innovation in the beverage dispensing industry, designed to cater to the evolving needs of commercial establishments. This advanced system combines state-of-the-art technology with user-friendly features, making it a standout choice for restaurants, cafes, and bars aiming to enhance their beverage service.

One of the main features of the Cornelius 10,000 PLUS is its impressive capacity. With the ability to dispense a wide variety of beverages, including soft drinks, cocktails, and craft beers, the system supports a large volume of service, perfect for high-demand environments. The modular design allows for easy expansion, enabling businesses to add additional flavors or beverages as needed without major overhauls.

The technology behind the Cornelius 10,000 PLUS is equally impressive. It utilizes advanced cooling technology to ensure that beverages are served at the optimal temperature, enhancing the customer experience. The integrated touchless dispensing mechanism minimizes waste and ensures a hygienic experience, addressing growing concerns about cleanliness in food service environments. This technology also improves speed, allowing staff to serve customers more efficiently.

Another key characteristic of the Cornelius 10,000 PLUS is its digital integration capabilities. The system can be connected to a central management platform that tracks sales, inventory levels, and maintenance needs in real-time. This allows operators to optimize their beverage offerings based on customer preferences and reduces downtime through proactive maintenance alerts.

In addition to its performance features, the Cornelius 10,000 PLUS is designed with sustainability in mind. The system employs energy-efficient practices, reducing its environmental footprint while lowering operational costs. The materials used in construction are durable yet eco-friendly, ensuring longevity and less waste.

Overall, the Cornelius 10,000 PLUS stands out as an essential tool for any business looking to elevate its beverage service. With its combination of high capacity, cutting-edge technology, and sustainability features, it not only meets the demands of today’s fast-paced service environments but also positions establishments for future growth and success.
Top Page Image Contents