CYCLE SEQUENCE
Anytime cycle sequence is modified, softener
Cycle Sequence instructions allows the operator to set the order of the cycle. The Softener System Setup allows the operator to set how long the cycles will last. The operator may choose up to 9 cycles in any order.
END must be used as the last cycle option. The SERVICE cycle should only be used in brine prefill applications to allow salt to dissolve.
Cycle Options
BACKWASH | REGENERANT | FILL |
| ||
RINSE | SOFTENING | END |
|
|
|
The following is an example of how to set a valve so that when regeneration is initiated, BACKWASH occurs first, regenerant draw DN occurs second, RINSE occurs third, and FILL occurs fourth.
| STEP 1 CS – Press NEXT and simultaneously for five seconds or until display changes and |
Step 1CS | |
| release. Then press NEXT and simultaneously again for 5 seconds and release. If screen in |
| |
| step 2CS does not appear in 5 seconds the lock on the valve is activated. |
SET 1.25
AUX VALVE CONTROL SET OFF
Step 2CS
Step 3CS
STEP 2 CS – Meter Size. Use the or to select from 1.0", 1.25", 1.50", 2.0" meter. H125 is a 1.25" meter. It is necessary to select meter size to coincide with control valve size used. Press NEXT to go to Step 3C.
STEP 3CS – Use the or to select on of the following:
•OFF; or
•Brine Reclaim – Step 4CS; or
•Twin Alternating System – Step 6CS; or
•No Hard Water Bypass During Regeneration – Step 7CS.
•Factory Setting is OFF
Brine Reclaim: When Reclamation Mode is ENABLED, a portion of the unused brine is diverted after it has passed through the resin bed. Brine discharge contains unused salt that can be used for brine
Programming needed for Brine Recovery: 1. Start Time
2. Duration
3. Lower Salt Setting
|
| BRINE RECLAIM |
| |
|
| start time / duration / salt setting - 10 lbs./ft3 |
| |
Water Pressure |
| |||
35 PSI | 40:00/10:00/2.0 | 40:00/12:00/3.3 | 46:00/11:00/4.2 |
|
45 PSI | 36:00/8:45/2.0 | 38:00/11:00/3.3 | 44:00/11:00/4.3 |
|
55 PSI | 33:00/8:30/2.0 | 36:00/11:00/3.3 | 41:00/8:30/4.0 |
|
65 PSI | 32:00/7:45/2.0 | 35:00/9:45/3.0 | 40:00/7:40/4.0 |
|
|
|
|
| |
|
|
|
| |
|
| start time / duration / salt setting - 10 lbs./ft3 |
| |
Water Pressure | ||||
35 PSI | 46:00/13:00/6.0 | 48:00/12:00/8.0 | 50:00/12:00/10.3 | 50:00/10:00/12.0 |
45 PSI | 44:00/11:00/6.5 | 46:00/11:00/8.0 | 48:00/10:00/10.3 | 48:00/9:30/12.0 |
55 PSI | 41:00/10:40/6.0 | 43:00/9:45/8.0 | 45:00/9:40/10.0 | 45:00/8:30/12.0 |
65 PSI | 40:00/10:00/6.0 | 42:00/8:55/8.0 | 44:00/8:55/10.0 | 44:00/7:50/12.0 |
|
|
|
|
|
15