Argosy Research H-125 Series owner manual Off

Page 17

AUXILIARY INPUT

Step 8CS

SET

OFF

REG

 

 

 

 

 

BACKWASH

Step 9CS

SET CYCLE1

 

STEP 8CS – If Twin Alternating capability is selected, auxilliary input option is not available. This display will be available to select the use of an outside signal to control the initiation of a regenera- tion. Selection only matters if a connection is made to the two pin connector labeled DP SWITCH located on the printed circuit board. Following is an explanation of the options:

•ON 0 REG – If the dP switch is closed for an accumulative time of 2 minutes, a regeneration will occur immediately.

•DELAY REG – If the dP switch is closed for an accumulative time of 2 minutes, a regeneration will occur at the schedule regeneration time.

•HOLD REG – If the dP switch is closed a regeneration will be prevented from occurring.

•OFF

Press NEXT to go to Step 9CS. Press REGEN to return to previous step.

STEP 9CS – Press the or buttons until selection of first cycle appears in left upper corner, in this example BACKWASH is selected. Press NEXT to go to Step 10CS. Press REGEN to return to previous step.

REGENERANT DRAW DN

Step 10CS

SET CYCLE2

 

RINSESET CYCLE 3 Step 11CS

 

FILL

CYCLE 4 Step 12CS

SET

 

SETEND

CYCLE 5 Step 13CS

 

STEP 10CS – Press the or buttons until selection of second cycle appears in left upper corner, in this example Regenerant Draw DN is selected. For a PM6 control valve prior to select- ing DN or UP or not selecting a regenerant flow cycle, verify the correct valve body, main piston, regenerant piston and stack are being used and the injector or injector plug(s) are in the correct location. Press NEXT to go to Step 11CS. Press REGEN to return to previous step.

STEP 11CS – Press the or buttons until selection of third cycle appears in left upper corner, in this example RINSE is selected. Press NEXT to go to Step 12CS. Press REGEN to return to previous step.

STEP 12CS – Press the or buttons until selection of fourth cycle appears in left upper corner, in this example FILL is selected. Press NEXT to go to Step 13CS. Press REGEN to return to previous step.

STEP 13CS – Press the or buttons until last regeneration cycle; END appears. (Up to 9 regeneration modes are possible). END MUST BE SELECTED AS LAST CYCLE.

RETURN TO ROTATING DISPLAY

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents With HP Electronics Table of Contents On TimeRelay Job Specification SheetOperating Conditions Soft Water BasicsBypass valve Operation Pre-Installation Check ListInstallation Instructions 650 User displays/settings635 Programming635PM Installer DISPLAYS/SETTINGS20 GR SET Time of DAYSoftener setup Cycle time adjustments800 MIN SET 12000 MIN6000 MIN MIN300 MIN 001 MINSET Regengal Service Reminder342 GAL DiagnosticsReset Diagnostic Values Hold Valve History 175 x1KBrine Reclaim Cycle Sequence800MIN EnabledOFF Miscellaneous Water Softener Draining ProcedureWater Softener Disinfection Cause Correction Trouble ShootingTrouble Shooting Problem Cause Relay troubleshootingDescription Qty H125 conditioner & salt keeper assembliesTank Assy Mineral Tank Distributor AssyDrawing no Order no Description Quantity Front Cover and Drive AssemblyInjector CAP, Injector SCREEN, INJECTOR, Plug and O-RING Spacer Stack AssemblyProper flow Drain line Drain line 3/4Bypass valve Water meter and meter plugInstallation fitting assemblies Wrench Flow Diagrams Service and Backwash Flow Diagrams Downflow Flow Diagrams Rinse and Fill Factory Regeneration Settings H125 SpecificationsProgramming options General specificationsResults Reserve capacity estimate based on history of water usageService Instructions Compliance Table Spacer Stack AssemblyRefill Flow Control Assembly or Refill Port Plug Page Page H125 Series Water Softeners Limited warranty
Top Page Image Contents