Craftsman 139.18595 Install the Lights, Attach the Emergency Release Rope and Handle, Release Tab

Page 18

INSTALLATION STEP 7

Install the Lights

Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens.

Install up to a 100 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF.

Reverse the procedure to close the lens.

If the bulbs burn out prematurely due to vibration, replace with a Garage Door Opener bulb.

NOTE: Use only standard light bulbs. The use of short neck or speciality light bulbs may overheat the endpanel or light socket.

CAUTION

To prevent possible OVERHEATING of the endpanel or light socket:

DO NOT use short neck or specialty light bulbs.

DO NOT use halogen bulbs. Use ONLY incandescent.

100 Watt (Max)

Standard Light Bulb

Release Tab

100 Watt (Max)

Lens

Hinge

Standard

 

Light Bulb

 

INSTALLATION STEP 8

Attach the Emergency Release Rope and Handle

Thread one end of the rope through the hole in the top of the red handle so “NOTICE” reads right side up as shown. Secure with an overhand knot at least 1" (2.5 cm) from the end of the rope to prevent slipping.

Thread the other end of the rope through the hole in the release arm of the outer trolley.

Adjust rope length so the handle is 6 feet (1.83 m) above the floor. Ensure that the rope and handle clear the tops of all vehicles to avoid entanglement. Secure with an overhand knot.

NOTE: If it is necessary to cut the rope, heat seal the cut end with a match or lighter to prevent unraveling.

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling garage door:

If possible, use emergency release handle to disengage trolley ONLY when garage door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

NEVER use emergency release handle unless garage doorway is clear of persons and obstructions.

NEVER use handle to pull door open or closed. If rope knot becomes untied, you could fall.

Trolley

Trolley

Release arm

Overhand

EmergencyKnot

Release Handle

18

Image 18
Contents Garage Door Opener Table of Contents IntroductionPreparing your garage door Tools neededPlanning Sectional Door InstallationsSectional Door Installation Trolley Stop Bolt TrolleyONE-PIECE Door with Track ONE-PIECE Door InstallationsONE-PIECE Door Without Track Trolley Stop BoltCarton Inventory Keyless Entry Hanging Brackets Straight Door Arm SectionAssembly Hardware Installation HardwareHardware Inventory Hole on TOPTapered End Assembly StepAssemble the Rail & Install the Trolley Clip Tapered End RailInstall the Idler Pulley Fasten the Rail to the Motor UnitInstall the Chain/Cable Installation Tighten the ChainInstallation Step Determine the Header Bracket LocationInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Header Bracket Mounting Hole Existing Clevis Pin Spacer Attach the Rail to the Header BracketHeader Wall Header Bracket Idler Pulley Garage Door Opener Carton or Temporary SupportRail Door 2x4 is used to determine Position the OpenerSectional Door or ONE-PIECE Door with Track From ceilingSupports Hang the OpenerStructural Bolt 5/16-18x7/8 Nut 5/16-18 Lock Washer 5/16Strip wire 7/16 11 mm Install the Door ControlTo release wire, push Tab with screwdriver tipInstall the Lights Attach the Emergency Release Rope and HandleRelease Tab Electrical Requirements Sensor Beam Invisible Light Beam Cm max Install The Protector SystemImportant Information about Safety Reversing Sensor Protection AreaWall installation Installing the BracketsGarage door track installation preferred Floor installation FigureTroubleshooting the Safety Sensors Mounting and Wiring the Safety SensorsAligning the Safety Sensors Quick-Connect TerminalsFasten the Door Bracket Sectional DoorsONE-PIECE Doors Header Wall 2x4TrolleyTrolley Connect Door Arm to TrolleySectional Doors only Emergency Release DoorHandle Bracket Straight Door ArmAssemble the door arm, Figure Adjustment procedures, FigureALL ONE-PIECE Doors Connect the door arm to the trolleyIf door does not open at least 5 feet 1.5 m Adjustment StepAdjust the UP and Down Travel Limits If the door does not close completelyTest the Down close force Adjust the ForceHOW and When to Adjust the Forces Test the UP open forceImportant Safety Check Test the Safety Reversal SystemAdjust Test The Protector SystemUsing Your Garage Door Opener OperationActivate your opener with any of the following Premium Control Console Light featureLock feature Disconnect the TrolleyTwice a Year Care of Your OpenerOnce a Month Once a YearHaving a PROBLEM? My door will not close and the light bulbs blinkSymptom LED is not lit on door control Symptom Motor unit doesn’t operateProgramming To Add or Reprogram a Hand-held Remote ControlUsing the Learn Button Using the Premium Control Console To Erase All Codes From Motor Unit MemoryTo Add, Reprogram or Change a Keyless Entry PIN To change an existing, known PINTo set a temporary PIN KEY Part Description Repair PartsRail Assembly Parts Not ShownComplete with Spring washer Motor Unit Assembly PartsBracket, bearing assembly, RPM Sensor Complete with Motor, wormParts & Service AccessoriesWarranty Sears WarrantyGet it fixed, at your home or ours Pour un bon fonctionnement en toute Sécurité de cet ouvre-porte de garageLe vérifier et le régler périodiquement Introduction Accessoires Garantie Pièces de réparation et serviceRevue des symboles de sécurité et des mots de signalement MontagePour prévenir d’éventuelles Blessures Graves ou Préparation de votre porte de garageOutils nécessaires Porte articulée Porte rigidePlanification Pose DE Portes ArticuléesPose DE Porte Articulée Et le bas de la porte ne doit De porte Planification SuitePose DE Porte Rigide Porte de DurgenceInventaire de la boîte d’emballage Inventaire des fixations Fixations Pour LE MontageFixations Pour LA Pose Montage 1re Opération Montage du rail et pose du chariotFixation du rail au moteur Montage 2e OpérationMontage 3e Opération Pose de la poulieMontage 4e Opération Pose de la chaîne et du câbleMontage 5e Opération Tension de la chaîneDéterminer l’emplacement du support de linteau Pose 1re OpérationPose DU Support DE Linteau AU MUR Pose 2e OpérationPose du support de linteau Pose DU Support DE Linteau AU PlafondPose 3e Opération Fixation du rail sur le support de linteauPorte Articulée OU Porte Rigide Avec Guides Pose 4e OpérationPositionnement de louvre-porte Porte Rigide Sans GuidesPose 5e Opération Accrochage de louvre-portePlacer le fil de l’antenne comme montré Pose de la commande de portePose 6e Opération Raccordements à une serrure à clé extérieurePose des ampoules Pose 7e OpérationPose 8e Opération Languette de dégagementLouvre-porte doit obligatoirement être mis à la terre Pose 9e OpérationExigences électriques Reposer le couverclePose 10e Opération Pose du Système ProtectorFaisant face à la porte depuis lintérieur du garage ’assurer que l’ouvre-porte est hors tension Pose aux guides de la porte de garage mode préférablePose DES Supports Pose murale etMontage ET Câblage DES Détecteurs Inverseurs Alignement DES Détecteurs InverseursDépannage DES Détecteurs Inverseurs DE Sécurité Pose 11e Opération Fixation du support de portePortes Articulées Portes Rigides De la portePour une porte sans cadre exposé Pose 12e Opération Fixation de la biellette au chariotPorte Articulée Seulement Méthodes de réglage, Figure Pour Toutes LES Portes RigidesAssemblage des biellettes, Figure De courseComment ET Quand Régler LES Courses Réglages 1re OpérationRéglage des courses d’ouverture et de fermeture Si la porte ne souvre pas dau moins Pieds 1,5 mComment ET Quand Régler LES Forces Réglages 2e OpérationRéglage de la force Vérification de la force de fermeture DownEssai du système d’inversion de sécurité Réglages 3e OpérationRéglages 4e Opération Essai du Systéme ProtectorUtilisation de votre ouvre-porte de garage Ou un 2 x 4 posé à plat sur le solActionner l’ouvre-porte suivant l’une des méthodes ci-après Fonction déclairage Utilisation de la commande de porte muralOuverture manuelle de la porte Fonction de verrouillageUne fois par mois Réglages DE Course ET DE Force LA Pile DE LA TélécommandePériodicités D’ENTRETIEN Deux fois par annéeMes télécommandes ne font pas fonctionner la porte ’éclairage ne s’éteint pas quand la porte est ouverteLe moteur de l’ouvre-porte ronfle brièvement Court-circuit de la commande de porte ou du fil Symptôme Le moteur ne fonctionne pasPour ajouter ou reprogrammer une télécommande à main Télécommande à trois fonctionsPour effacer tous les codes de la Mémoire du moteur Pour modifier un NIP connu, existant Pour définir un NIP temporaireRÉF Pièce Désignation Pièces d’assemblage du railPièces pour la pose NON Illustrés108D67 Diffuseur Les étiquettes 30B532 Condensateur 1/2HP Comprend Rondelle deRetenue d’interrupteur de fin de NON Illustré’entremise des Pièces et Service Disponible uniquement parSears LE-FOYERMD

139.18595 specifications

The Craftsman 139.18595 is a robust and reliable garage door opener that combines practicality with advanced technology, making it an ideal choice for homeowners. This model is designed to enhance convenience and security while ensuring smooth operation over time.

One of the standout features of the Craftsman 139.18595 is its powerful 1/2 horsepower motor. This motor provides sufficient power to lift even the heaviest of garage doors, making it a great option for homeowners with larger or heavier doors. The opener operates quietly, reducing noise disturbances, particularly when the door is in use early in the morning or late at night.

In terms of technology, the Craftsman 139.18595 is equipped with a reliable belt drive system. This feature not only contributes to its quiet operation but also ensures longevity and minimal maintenance. Unlike chain-driven models, the belt drive system reduces wear and tear, making it an ideal option for those looking for a long-term investment.

The garage door opener comes with a suite of safety features, including the photo-eye sensor technology. This system detects objects in the door's path, automatically reversing its direction to prevent accidents. This feature is particularly useful for families with pets or small children, providing added peace of mind during operations.

Additionally, the Craftsman 139.18595 offers modern connectivity options. It is compatible with many smartphone apps, allowing users to control and monitor their garage door remotely. This smart technology adds convenience, enabling homeowners to open or close their garage door from virtually anywhere.

Installation of the Craftsman 139.18595 is straightforward, thanks to its user-friendly design and comprehensive instruction manual. Whether you are a seasoned DIY enthusiast or new to home improvement projects, you can set up the opener with relative ease.

In summary, the Craftsman 139.18595 stands out for its powerful motor, quiet belt drive system, advanced safety features, and smart connectivity options. This garage door opener not only enhances the functionality and security of your home but also embodies the quality and craftsmanship that the Craftsman brand is known for.