Craftsman 139.18595 owner manual Care of Your Opener, Once a Month, Twice a Year, Once a Year

Page 32
Open this end first to avoid cracking housing

CARE OF YOUR OPENER

LIMIT AND FORCE ADJUSTMENTS:

Weather conditions may

FORCE CONTROLS

cause some minor changes

 

 

 

 

 

 

 

 

in door operation requiring

9

1

9

1

some re-adjustments,

7

5

7

5

 

3

3

particularly during the first

 

KG

 

KG

year of operation.

 

 

 

 

Pages 27 and 28 refer to the LIMIT CONTROLS limit and force adjustments.

Only a screwdriver is required. Follow the

instructions carefully.

Repeat the safety reverse test (Adjustment

Step 3, page 29) after any adjustment of limits or force.

MAINTENANCE SCHEDULE

Once a Month

•Manually operate door. If it is unbalanced or binding, call a trained door systems technician.

•Check to be sure door opens & closes fully. Adjust limits and/or force if necessary. (See pages 27 and 28)

•Repeat the safety reverse test. Make any necessary adjustments. (See Adjustment Step 3)

Twice a Year

•Check chain tension. Disconnect trolley first. Adjust if necessary. (See page 11)

Once a Year

•Oil door rollers, bearings and hinges. The opener does not require additional lubrication. Do not grease the door tracks.

THE REMOTE CONTROL BATTERY

WARNING

To prevent possible SERIOUS INJURY or DEATH:

•NEVER allow small children near batteries.

•If battery is swallowed, immediately notify doctor.

The lithium battery should produce power for up to

5 years. To replace battery, use the visor clip or screwdriver blade to pry open

the case as shown. Insert battery, matching polarity

instructions inside the remote cover or on the printed circuit board.

Dispose of old battery properly.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2)this device must accept any interference received, including interference that may cause undesired operation.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Garage Door Opener Table of Contents IntroductionPreparing your garage door Tools neededSectional Door Installations Sectional Door InstallationPlanning Trolley Stop Bolt TrolleyONE-PIECE Door Installations ONE-PIECE Door Without TrackONE-PIECE Door with Track Trolley Stop BoltCarton Inventory Keyless Entry Hanging Brackets Straight Door Arm SectionHardware Inventory Assembly HardwareInstallation Hardware Assembly Step Assemble the Rail & Install the TrolleyHole on TOPTapered End Clip Tapered End RailInstall the Idler Pulley Fasten the Rail to the Motor UnitInstall the Chain/Cable Installation Tighten the ChainInstallation Step Determine the Header Bracket LocationCeiling Header Bracket Installation Install the Header BracketWall Header Bracket Installation Attach the Rail to the Header Bracket Header Wall Header Bracket Idler Pulley Garage DoorHeader Bracket Mounting Hole Existing Clevis Pin Spacer Opener Carton or Temporary SupportPosition the Opener Sectional Door or ONE-PIECE Door with TrackRail Door 2x4 is used to determine From ceilingHang the Opener StructuralSupports Bolt 5/16-18x7/8 Nut 5/16-18 Lock Washer 5/16Install the Door Control To release wire, pushStrip wire 7/16 11 mm Tab with screwdriver tipRelease Tab Install the LightsAttach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System Important Information about Safety Reversing SensorSensor Beam Invisible Light Beam Cm max Protection AreaInstalling the Brackets Garage door track installation preferredWall installation Floor installation FigureMounting and Wiring the Safety Sensors Aligning the Safety SensorsTroubleshooting the Safety Sensors Quick-Connect TerminalsFasten the Door Bracket Sectional DoorsONE-PIECE Doors Header Wall 2x4Connect Door Arm to Trolley Sectional Doors onlyTrolleyTrolley Emergency Release DoorHandle Bracket Straight Door ArmAdjustment procedures, Figure ALL ONE-PIECE DoorsAssemble the door arm, Figure Connect the door arm to the trolleyAdjustment Step Adjust the UP and Down Travel LimitsIf door does not open at least 5 feet 1.5 m If the door does not close completelyAdjust the Force HOW and When to Adjust the ForcesTest the Down close force Test the UP open forceTest the Safety Reversal System AdjustImportant Safety Check Test The Protector SystemActivate your opener with any of the following Using Your Garage Door OpenerOperation Light feature Lock featurePremium Control Console Disconnect the TrolleyCare of Your Opener Once a MonthTwice a Year Once a YearHaving a PROBLEM? My door will not close and the light bulbs blinkSymptom LED is not lit on door control Symptom Motor unit doesn’t operateTo Add or Reprogram a Hand-held Remote Control Using the Learn Button Using the Premium Control ConsoleProgramming To Erase All Codes From Motor Unit MemoryTo set a temporary PIN To Add, Reprogram or Change a Keyless Entry PINTo change an existing, known PIN Repair Parts Rail Assembly PartsKEY Part Description Not ShownMotor Unit Assembly Parts Bracket, bearing assembly, RPM SensorComplete with Spring washer Complete with Motor, wormAccessories WarrantyParts & Service Sears WarrantyGet it fixed, at your home or ours Le vérifier et le régler périodiquement Pour un bon fonctionnement en touteSécurité de cet ouvre-porte de garage Accessoires Garantie Pièces de réparation et service Revue des symboles de sécurité et des mots de signalementIntroduction MontagePréparation de votre porte de garage Outils nécessairesPour prévenir d’éventuelles Blessures Graves ou Porte articulée Porte rigidePose DE Porte Articulée PlanificationPose DE Portes Articulées Planification Suite Pose DE Porte RigideEt le bas de la porte ne doit De porte Porte de DurgenceInventaire de la boîte d’emballage Fixations Pour LA Pose Inventaire des fixationsFixations Pour LE Montage Montage 1re Opération Montage du rail et pose du chariotMontage 2e Opération Montage 3e OpérationFixation du rail au moteur Pose de la poulieMontage 4e Opération Pose de la chaîne et du câbleMontage 5e Opération Tension de la chaîneDéterminer l’emplacement du support de linteau Pose 1re OpérationPose 2e Opération Pose du support de linteauPose DU Support DE Linteau AU MUR Pose DU Support DE Linteau AU PlafondPose 3e Opération Fixation du rail sur le support de linteauPose 4e Opération Positionnement de louvre-portePorte Articulée OU Porte Rigide Avec Guides Porte Rigide Sans GuidesPose 5e Opération Accrochage de louvre-portePose de la commande de porte Pose 6e OpérationPlacer le fil de l’antenne comme montré Raccordements à une serrure à clé extérieurePose 7e Opération Pose 8e OpérationPose des ampoules Languette de dégagementPose 9e Opération Exigences électriquesLouvre-porte doit obligatoirement être mis à la terre Reposer le couvercleFaisant face à la porte depuis lintérieur du garage Pose 10e OpérationPose du Système Protector Pose aux guides de la porte de garage mode préférable Pose DES Supports’assurer que l’ouvre-porte est hors tension Pose murale etDépannage DES Détecteurs Inverseurs DE Sécurité Montage ET Câblage DES Détecteurs InverseursAlignement DES Détecteurs Inverseurs Portes Articulées Pose 11e OpérationFixation du support de porte Pour une porte sans cadre exposé Portes RigidesDe la porte Porte Articulée Seulement Pose 12e OpérationFixation de la biellette au chariot Pour Toutes LES Portes Rigides Assemblage des biellettes, FigureMéthodes de réglage, Figure De courseRéglages 1re Opération Réglage des courses d’ouverture et de fermetureComment ET Quand Régler LES Courses Si la porte ne souvre pas dau moins Pieds 1,5 mRéglages 2e Opération Réglage de la forceComment ET Quand Régler LES Forces Vérification de la force de fermeture DownRéglages 3e Opération Réglages 4e OpérationEssai du système d’inversion de sécurité Essai du Systéme ProtectorActionner l’ouvre-porte suivant l’une des méthodes ci-après Utilisation de votre ouvre-porte de garageOu un 2 x 4 posé à plat sur le sol Utilisation de la commande de porte mural Ouverture manuelle de la porteFonction déclairage Fonction de verrouillageRéglages DE Course ET DE Force LA Pile DE LA Télécommande Périodicités D’ENTRETIENUne fois par mois Deux fois par annéeLe moteur de l’ouvre-porte ronfle brièvement Mes télécommandes ne font pas fonctionner la porte’éclairage ne s’éteint pas quand la porte est ouverte Court-circuit de la commande de porte ou du fil Symptôme Le moteur ne fonctionne pasPour effacer tous les codes de la Mémoire du moteur Pour ajouter ou reprogrammer une télécommande à mainTélécommande à trois fonctions Pour modifier un NIP connu, existant Pour définir un NIP temporairePièces d’assemblage du rail Pièces pour la poseRÉF Pièce Désignation NON IllustrésComprend Rondelle de Retenue d’interrupteur de fin de108D67 Diffuseur Les étiquettes 30B532 Condensateur 1/2HP NON IllustréSears ’entremise des Pièces et ServiceDisponible uniquement par LE-FOYERMD

139.18595 specifications

The Craftsman 139.18595 is a robust and reliable garage door opener that combines practicality with advanced technology, making it an ideal choice for homeowners. This model is designed to enhance convenience and security while ensuring smooth operation over time.

One of the standout features of the Craftsman 139.18595 is its powerful 1/2 horsepower motor. This motor provides sufficient power to lift even the heaviest of garage doors, making it a great option for homeowners with larger or heavier doors. The opener operates quietly, reducing noise disturbances, particularly when the door is in use early in the morning or late at night.

In terms of technology, the Craftsman 139.18595 is equipped with a reliable belt drive system. This feature not only contributes to its quiet operation but also ensures longevity and minimal maintenance. Unlike chain-driven models, the belt drive system reduces wear and tear, making it an ideal option for those looking for a long-term investment.

The garage door opener comes with a suite of safety features, including the photo-eye sensor technology. This system detects objects in the door's path, automatically reversing its direction to prevent accidents. This feature is particularly useful for families with pets or small children, providing added peace of mind during operations.

Additionally, the Craftsman 139.18595 offers modern connectivity options. It is compatible with many smartphone apps, allowing users to control and monitor their garage door remotely. This smart technology adds convenience, enabling homeowners to open or close their garage door from virtually anywhere.

Installation of the Craftsman 139.18595 is straightforward, thanks to its user-friendly design and comprehensive instruction manual. Whether you are a seasoned DIY enthusiast or new to home improvement projects, you can set up the opener with relative ease.

In summary, the Craftsman 139.18595 stands out for its powerful motor, quiet belt drive system, advanced safety features, and smart connectivity options. This garage door opener not only enhances the functionality and security of your home but also embodies the quality and craftsmanship that the Craftsman brand is known for.
Top Page Image Contents