Craftsman 139.18595 owner manual Fasten the Rail to the Motor Unit, Install the Idler Pulley

Page 9

ASSEMBLY STEP 2

Fasten the Rail to the Motor Unit

•Insert a 1/4"-20x1-3/4 bolt into the cover protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4"-20 lock nut. Do NOT overtighten.

•Remove the two bolts from the top of the motor unit.

•Place the “U” bracket, flat side down onto the motor unit and align the bracket hole with the bolt holes. Fasten with the previously removed bolts.

•Align the rail assembly with the top of the motor unit. Slide the rail end onto the “U” bracket, all the way to the stops that protrude on the top and sides of the bracket.

•Attach spreader to the motor unit with two screws.

HARDWARE SHOWN ACTUAL SIZE

CAUTION

To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener.

Hex Screws 8-32x7/16"

 

Chain

Bolts

Spreader

 

 

Motor Unit

"U" Bracket

Sprocket

 

Bolt

Cover

Protection

Bolt Hole

 

Lock Nut

Bolt 1/4"-20x1-3/4"

1/4"-20

ASSEMBLY STEP 3

Install the Idler Pulley

• Lay the chain/cable beside the rail, as shown.

Grasp the end of the cable and pass

approximately 12" (30 cm) of cable through the

window. Allow it to hang until Assembly Step 5.

Lock Nut

Chain and Cable

SLIDE RAIL TO STOPS ON TOP AND SIDES OF BRACKET

Bolt

Pulley Rail

Nut

Washer

•

Remove the tape from the idler pulley. The inside

 

center should be pre-greased. If dry, regrease to

 

ensure proper operation.

•

Place the idler pulley into the window as shown.

•

Insert the idler bolt from the top through the rail

 

and pulley. Tighten with a 3/8" lock washer and nut

 

underneath the rail until the lock washer is

 

compressed.

•

Rotate the pulley to be sure it spins freely.

•

Insert a 1/4"-20x1-3/4 bolt into the trolley stop hole

 

in the front of the rail as shown. Tighten securely

 

with a 1/4"-20 lock nut.

Idler

Screwdriver Trolley

Bolt

 

Bolt

Trolley

Stop Hole

 

Grease

 

Inside Pulley

Lock

Idler

Washer

Pulley

3/8"

Nut 3/8"

 

 

Cable Link

Lock

Idler Nut

Pulley

HARDWARE SHOWN ACTUAL SIZE

Idler Bolt

Bolt 1/4"-20x1-3/4"

Lock Nut 1/4"-20

Nut 3/8"

Lock Washer 3/8"

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Garage Door Opener Introduction Table of ContentsTools needed Preparing your garage doorSectional Door Installation Sectional Door InstallationsPlanning Trolley Stop Bolt TrolleyONE-PIECE Door Without Track ONE-PIECE Door InstallationsONE-PIECE Door with Track Trolley Stop BoltKeyless Entry Hanging Brackets Straight Door Arm Section Carton InventoryAssembly Hardware Installation HardwareHardware Inventory Assemble the Rail & Install the Trolley Assembly StepHole on TOPTapered End Clip Tapered End RailFasten the Rail to the Motor Unit Install the Idler PulleyInstall the Chain/Cable Tighten the Chain InstallationDetermine the Header Bracket Location Installation StepInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Header Wall Header Bracket Idler Pulley Garage Door Attach the Rail to the Header BracketHeader Bracket Mounting Hole Existing Clevis Pin Spacer Opener Carton or Temporary SupportSectional Door or ONE-PIECE Door with Track Position the OpenerRail Door 2x4 is used to determine From ceilingStructural Hang the OpenerSupports Bolt 5/16-18x7/8 Nut 5/16-18 Lock Washer 5/16To release wire, push Install the Door ControlStrip wire 7/16 11 mm Tab with screwdriver tipInstall the Lights Attach the Emergency Release Rope and HandleRelease Tab Electrical Requirements Important Information about Safety Reversing Sensor Install The Protector SystemSensor Beam Invisible Light Beam Cm max Protection AreaGarage door track installation preferred Installing the BracketsWall installation Floor installation FigureAligning the Safety Sensors Mounting and Wiring the Safety SensorsTroubleshooting the Safety Sensors Quick-Connect TerminalsSectional Doors Fasten the Door BracketHeader Wall 2x4 ONE-PIECE DoorsSectional Doors only Connect Door Arm to TrolleyTrolleyTrolley Emergency Release DoorHandle Bracket Straight Door ArmALL ONE-PIECE Doors Adjustment procedures, FigureAssemble the door arm, Figure Connect the door arm to the trolleyAdjust the UP and Down Travel Limits Adjustment StepIf door does not open at least 5 feet 1.5 m If the door does not close completelyHOW and When to Adjust the Forces Adjust the ForceTest the Down close force Test the UP open forceAdjust Test the Safety Reversal SystemImportant Safety Check Test The Protector SystemUsing Your Garage Door Opener OperationActivate your opener with any of the following Lock feature Light featurePremium Control Console Disconnect the TrolleyOnce a Month Care of Your OpenerTwice a Year Once a YearMy door will not close and the light bulbs blink Having a PROBLEM?Symptom Motor unit doesn’t operate Symptom LED is not lit on door controlUsing the Learn Button Using the Premium Control Console To Add or Reprogram a Hand-held Remote ControlProgramming To Erase All Codes From Motor Unit MemoryTo Add, Reprogram or Change a Keyless Entry PIN To change an existing, known PINTo set a temporary PIN Rail Assembly Parts Repair PartsKEY Part Description Not ShownBracket, bearing assembly, RPM Sensor Motor Unit Assembly PartsComplete with Spring washer Complete with Motor, wormWarranty AccessoriesParts & Service Sears WarrantyGet it fixed, at your home or ours Pour un bon fonctionnement en toute Sécurité de cet ouvre-porte de garageLe vérifier et le régler périodiquement Revue des symboles de sécurité et des mots de signalement Accessoires Garantie Pièces de réparation et serviceIntroduction MontageOutils nécessaires Préparation de votre porte de garagePour prévenir d’éventuelles Blessures Graves ou Porte articulée Porte rigidePlanification Pose DE Portes ArticuléesPose DE Porte Articulée Pose DE Porte Rigide Planification SuiteEt le bas de la porte ne doit De porte Porte de DurgenceInventaire de la boîte d’emballage Inventaire des fixations Fixations Pour LE MontageFixations Pour LA Pose Montage du rail et pose du chariot Montage 1re OpérationMontage 3e Opération Montage 2e OpérationFixation du rail au moteur Pose de la pouliePose de la chaîne et du câble Montage 4e OpérationTension de la chaîne Montage 5e OpérationPose 1re Opération Déterminer l’emplacement du support de linteauPose du support de linteau Pose 2e OpérationPose DU Support DE Linteau AU MUR Pose DU Support DE Linteau AU PlafondFixation du rail sur le support de linteau Pose 3e OpérationPositionnement de louvre-porte Pose 4e OpérationPorte Articulée OU Porte Rigide Avec Guides Porte Rigide Sans GuidesAccrochage de louvre-porte Pose 5e OpérationPose 6e Opération Pose de la commande de portePlacer le fil de l’antenne comme montré Raccordements à une serrure à clé extérieurePose 8e Opération Pose 7e OpérationPose des ampoules Languette de dégagementExigences électriques Pose 9e OpérationLouvre-porte doit obligatoirement être mis à la terre Reposer le couverclePose 10e Opération Pose du Système ProtectorFaisant face à la porte depuis lintérieur du garage Pose DES Supports Pose aux guides de la porte de garage mode préférable’assurer que l’ouvre-porte est hors tension Pose murale etMontage ET Câblage DES Détecteurs Inverseurs Alignement DES Détecteurs InverseursDépannage DES Détecteurs Inverseurs DE Sécurité Pose 11e Opération Fixation du support de portePortes Articulées Portes Rigides De la portePour une porte sans cadre exposé Pose 12e Opération Fixation de la biellette au chariotPorte Articulée Seulement Assemblage des biellettes, Figure Pour Toutes LES Portes RigidesMéthodes de réglage, Figure De courseRéglage des courses d’ouverture et de fermeture Réglages 1re OpérationComment ET Quand Régler LES Courses Si la porte ne souvre pas dau moins Pieds 1,5 mRéglage de la force Réglages 2e OpérationComment ET Quand Régler LES Forces Vérification de la force de fermeture DownRéglages 4e Opération Réglages 3e OpérationEssai du système d’inversion de sécurité Essai du Systéme ProtectorUtilisation de votre ouvre-porte de garage Ou un 2 x 4 posé à plat sur le solActionner l’ouvre-porte suivant l’une des méthodes ci-après Ouverture manuelle de la porte Utilisation de la commande de porte muralFonction déclairage Fonction de verrouillagePériodicités D’ENTRETIEN Réglages DE Course ET DE Force LA Pile DE LA TélécommandeUne fois par mois Deux fois par annéeMes télécommandes ne font pas fonctionner la porte ’éclairage ne s’éteint pas quand la porte est ouverteLe moteur de l’ouvre-porte ronfle brièvement Symptôme Le moteur ne fonctionne pas Court-circuit de la commande de porte ou du filPour ajouter ou reprogrammer une télécommande à main Télécommande à trois fonctionsPour effacer tous les codes de la Mémoire du moteur Pour définir un NIP temporaire Pour modifier un NIP connu, existantPièces pour la pose Pièces d’assemblage du railRÉF Pièce Désignation NON IllustrésRetenue d’interrupteur de fin de Comprend Rondelle de108D67 Diffuseur Les étiquettes 30B532 Condensateur 1/2HP NON Illustré’entremise des Pièces et Service Disponible uniquement parSears LE-FOYERMD

139.18595 specifications

The Craftsman 139.18595 is a robust and reliable garage door opener that combines practicality with advanced technology, making it an ideal choice for homeowners. This model is designed to enhance convenience and security while ensuring smooth operation over time.

One of the standout features of the Craftsman 139.18595 is its powerful 1/2 horsepower motor. This motor provides sufficient power to lift even the heaviest of garage doors, making it a great option for homeowners with larger or heavier doors. The opener operates quietly, reducing noise disturbances, particularly when the door is in use early in the morning or late at night.

In terms of technology, the Craftsman 139.18595 is equipped with a reliable belt drive system. This feature not only contributes to its quiet operation but also ensures longevity and minimal maintenance. Unlike chain-driven models, the belt drive system reduces wear and tear, making it an ideal option for those looking for a long-term investment.

The garage door opener comes with a suite of safety features, including the photo-eye sensor technology. This system detects objects in the door's path, automatically reversing its direction to prevent accidents. This feature is particularly useful for families with pets or small children, providing added peace of mind during operations.

Additionally, the Craftsman 139.18595 offers modern connectivity options. It is compatible with many smartphone apps, allowing users to control and monitor their garage door remotely. This smart technology adds convenience, enabling homeowners to open or close their garage door from virtually anywhere.

Installation of the Craftsman 139.18595 is straightforward, thanks to its user-friendly design and comprehensive instruction manual. Whether you are a seasoned DIY enthusiast or new to home improvement projects, you can set up the opener with relative ease.

In summary, the Craftsman 139.18595 stands out for its powerful motor, quiet belt drive system, advanced safety features, and smart connectivity options. This garage door opener not only enhances the functionality and security of your home but also embodies the quality and craftsmanship that the Craftsman brand is known for.
Top Page Image Contents