KitchenAid 2316565B Installation Instructions, Unpack the Refrigerator, Reduce TippingRadius

Page 18

Inset Installation Dimensions

1.Measure the distance from point A (as shown) to the back wall. Add ¹⁄₃₂" (0.8 mm) to this measurement to allow the side panel to fit into the trim.

2.If the panel is more than ³⁄₈" (9.5 mm) thick, route the front edge to allow the side panel to fit into the trim.

A

Recessed Inset Installation Dimensions

1.Measure the distance from point A (as shown) to back wall.

2.Route the front edge of the support board or attach a ³⁄₈" (9.5 mm) board to hold the panel in the cabinet side trim.

A

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

Reduce TippingRadius

(if required)

Before bringing the refrigerator into the home, be sure there is adequate ceiling height to stand the refrigerator upright. See “Tipping Radius” in the “Installation Requirements” section for more information.

If you do not have adequate ceiling height to stand the refrigerator upright, the tipping radius can be reduced by removing the top grille and side trims (see the following chart).

Model Reduced Tipping Radius

3688" (223.5 cm)

4288¹⁄₂" (224.8 cm)

4889¹⁄₄" (226.7 cm)

1.Grasp both ends of the top grille.

2.Push the top grille straight up; then pull straight out. Lay the grille on a soft surface.

BAB

■Do not remove the protective film until the refrigerator is in its operating position.

■All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator.

■Keep the cardboard shipping piece or plywood under the refrigerator until it is installed in the operating position.

1.Remove and save the literature package bag taped to the side of the refrigerator and the parts bag behind the grille. Remove the four brackets (two on each side) that attach the shipping base to the refrigerator bottom.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final position.

2.If necessary, reduce the tipping radius. See “Tipping Radius” for ceiling height requirements or “Reduce Tipping Radius” for step-by-step instructions. If you do not need to reduce the tipping radius, proceed to “Move the Refrigerator into House.”

A. Top grille

B. Cabinet side trim

3.Remove the six screws attaching each cabinet side trim to the refrigerator and remove the side trims.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorTable of Contents ÍndiceTable DES Matières Refrigerator Safety Your safety and the safety of others are very importantArchitect Series ModelsSide by Side Non-Dispensing Refrigerators Classic SeriesSide by Side Dispensing Refrigerators Complete SeriesToolsand Parts Installation RequirementsOpening Dimensions Location RequirementsElectrical Requirements Recommended Grounding MethodModel Width a as shown above Water Pressure Water Supply RequirementsTipping Radius Reverse Osmosis Water SupplyTop View ProductDimensionsSide View Front View Model Width a Trim edge to trim edge42 106.7 cm Models Door SwingDimensions36 91.4 cm Models 48 121.9 cm ModelsOverlay Panel Overlay SeriesDoor Panel & CabinetryClearanceOverlayPanel OverlaySeries Custom Panelsand Handle Kits Decorative Overlay Panels ModelBacker Panels Model Classic SeriesFactory Panelsand Kits Top Grille Panel ClassicSeries Custom PanelsDoor Panels for Dispenser Models Door Panels for Non-dispenser ModelsDoor Panels Routing Requirements Refrigerator and Side Trim DimensionsClassic, Architect and Complete Series Custom Side Panels RefrigeratorRecessed Inset Installation Dimensions Refrigerator Inset Installation DimensionsFlush Installation Dimensions OverlaySeries Custom Side PanelsReduce TippingRadius Installation InstructionsUnpack the Refrigerator Measure the distance from point a as shown to back wallMove the Refrigerator into House Install Anti-Tip BoardsTo Install Anti-tip Boards Connectthe Water SupplyStyle 2 Copper Line Connection Connecting to Water Line Connecting to RefrigeratorPlug in Refrigerator MoveRefrigerator toFinal LocationLevel and Align Refrigerator Install ClassicSeries Custom Panels Check refrigerator level and adjustment. Adjust if neededDoor Panels Install OverlaySeries Custom Panels Door Panel InstallationDoor Swing Adjustment Adjust DoorsDoor Height Adjustment Door-to-Door or Door-to-Refrigerator Trim AdjustmentInstall Side Panel Install Base GrilleSnap the skirt onto the base grille Complete Installation Water System PreparationStyle 1 Non-Dispenser Models Style 2 Dispenser Models Page Seguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteSerie Architect ModelosRefrigeradores de dos puertas sin despachador Serie ClassicRefrigeradores de dos puertas con despachador Serie CompletaRequisitosde ubicación Requisitos DE InstalaciónPiezas y herramientas Medidas de la aberturaRequisitoseléctricos Método de conexión a tierra recomendadoModelo Ancho a Como se muestra anteriormente Presión del agua Requisitosdel suministro de aguaArco devuelco Suministro de agua de ósmosis inversaVista superior Medidas delproductoVista lateral Vista frontal Modelo Ancho aModelos de 42 106,7 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 48 121,9 cmPuerta Panel Paneles decorativos recubiertos Modelo Paneles de soporte ModeloPaneles y juegos de fábrica delaserie Classic Panel de la rejilla superior Panelesa la medida para la serie ClassicPaneles de puerta para modelos con despachador Paneles de puerta para modelos sin despachadorRefrigerador Requisitos de contorneado de los paneles de la puertaMedidas del refrigerador y del adorno lateral Agarradera extendida Vista superiorMedidas para la instalación empotrada Paneles laterales a la medida para la Serie OverlayAdornos laterales Medidas para la instalación al rasCómoreducirelarco de vuelco Instrucciones DE InstalaciónDesempaque el refrigerador Modelo Arco de vuelco reducidoCómo instalarlos tablerosantivuelco Cómo instalar los tableros antivuelcoConexión al refrigerador Conexión del suministro de aguaEstilo 1 Conexión de la válvula de cierre Lea todas las instrucciones antes de comenzarCómo enchufar elrefrigerador Cómo mover el refrigerador a su ubicación FinalNivelación yalineamientodel refrigerador Cómo instalar los paneles a la medida para la Serie Classic Paneles de la puertaInstalación del panel de la puerta Cómo ajustar la oscilación de las puertas Ajuste laspuertasCómo ajustar la altura de la puerta Modelos Classic y ArchitectCómoinstalar el panellateral Cómo instalar la rejilla de la baseCómoterminarla instalación Preparación del sistema de aguaSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteSérie Architect ModèlesRéfrigérateurs côte à côte sans distributeur Série ClassicRéfrigérateurs côte à côte avec distributeur Série ComplèteDimensions de l’ouverture Exigences D’INSTALLATIONExigences d’emplacement Outillage etpiècesMéthode recommandée de mise à la terre SpécificationsélectriquesModèle Largeur a tel quillustré ci-dessus Pression de leau Spécifications de l’alimentation en eauRayon debasculement Alimentation en eau par osmose inverseVue de dessus Dimensions du produitVue latérale Vue avant Modèle Largeur aModèles de 42 106,7 cm Dimensionspour le pivotement desportesModèles de 36 91,4 cm Modèles de 48 121,9 cmPorte Panneau Charnière Porte Panneaux personnalisés et poignéesde la série Overlay Panneau décoratif Overlay ModèlePanneau d’appui Modèle Ensemblesde panneaux dorigine de la série Classic Panneau de la grille supérieure Panneaux personnalisés de la Série ClassicPanneaux de porte pour modèles avec distributeur Panneaux de porte pour modèles sans distributeurRéfrigérateur Dimensions du réfrigérateur et des garnitures latéralesExigences dusinage des panneaux de porte Poignée de porte prolongée Vue supérieureDimensions pour un panneau inséré en retrait Dimensions pour un panneau inséréDimensions pour un panneau en affleurement Panneaux latéraux personnalisés de la Série OverlayRéduction du rayon de basculement Instructions D’INSTALLATIONDéballage du réfrigérateur Modèle Rayon de basculement réduitInstallation de planchesantibasculement Installation des planches antibasculementFaire entrerle réfrigérateur dans le domicile Raccordement au réfrigérateur Raccordementà la canalisation deauStyle 1 Raccordement sur robinet darrêt Ouvrir le robinet darrêtDéplacementdu réfrigérateur à Lemplacement final Brancher le réfrigérateurRéglage de laplomb etalignement du Réfrigérateur Installation despanneaux personnalisés De la Série Classic Panneaux de porteInstallation despanneaux personnalisés De la Série Overlay Installation des panneaux de porteAjustement du pivotement des portes Ajustement desportesAjustement de la hauteur des portes Modèles Classic et ArchitectInstallation du panneau latéral Installation de la grille de la baseVeuillez lire avant d’utiliser le système d’eau Acheverl’installationPréparation du système d’eau Style 1 Modèles sans distributeur2316565B All rights reserved

2316565B specifications

The KitchenAid 2316565B is a versatile and powerful kitchen appliance that enhances the cooking experience for home chefs and baking enthusiasts alike. Known for its durable construction and innovative features, this stand mixer is a must-have tool in any modern kitchen.

One of the standout features of the KitchenAid 2316565B is its robust 325-watt motor. This powerful motor ensures that the mixer can handle a variety of tasks, from kneading dense bread dough to whipping egg whites into fluffy peaks. The mixer operates with a reliable planetary mixing action, which means that the bowl and the beater rotate in opposite directions, ensuring that all ingredients are mixed thoroughly and evenly.

The KitchenAid 2316565B boasts a large capacity bowl that can hold up to 5 quarts. This generous size allows for mixing large batches of dough or batter, making it ideal for large families or entertaining guests. The stainless steel bowl is not only sturdy but also comes with a comfortable handle and is dishwasher safe, making cleanup a breeze.

Another impressive feature of this stand mixer is its 10-speed screw control. This allows users to easily adjust the mixing speed for various tasks, from slow stirring to fast whipping. The precision of the speed settings ensures that users can achieve the perfect consistency for every recipe.

KitchenAid has also designed the 2316565B with a tilt-head mechanism. This thoughtful design allows for easy access to the mixing bowl and makes it simple to add ingredients while the mixer is in operation. The mixer comes with a range of accessories, including a flat beater, a dough hook, and a wire whip, catering to different mixing needs and recipes.

In addition to its functionality, the KitchenAid 2316565B is available in a variety of colors, allowing users to choose one that fits their kitchen aesthetic. The mixer's classic design and robust performance make it not only a practical kitchen tool but also a stylish addition to any countertop.

Overall, the KitchenAid 2316565B stand mixer is a reliable, efficient, and aesthetically pleasing appliance that provides an enjoyable cooking experience. Whether you're a beginner in the kitchen or a seasoned chef, this stand mixer is designed to meet all your mixing, kneading, and whipping needs, making it a valuable addition to any home.
Top Page Image Contents