KitchenAid 2316565B manual Adjust Doors, Door Height Adjustment, Door Swing Adjustment

Page 24

Adjust Doors

Door Height Adjustment

Use the following steps to adjust the door height, up or down, after the doors have been leveled.

1.Open the freezer or refrigerator door. Locate the bottom hinge and remove the door stop screw.

Classic and Architect® Models

Remove the door stop screw from the bottom side of the hinge with a ³⁄₈" open end wrench.

AB C

A.Bushing

B.Door stop screw

C.Locking plate

Overlay Models

Remove the two door stop screws: one from the bottom side using a ³⁄₈" open end wrench and one from the top side using a ⁵⁄₃₂" Allen wrench.

AB

A.Door stop screw from bottom

B.Door stop screw from top (110°)

2.Remove the locking plate as shown.

3.Turn the bushing located underneath the bottom of the hinge using a ¹⁄₂" open end wrench. Turning the bushing to the left will lower the door. Turning the bushing right will raise the door.

4.After adjusting, check the doors to make sure they are even at the top and bottom. If the doors are not even, continue to turn the bushing to adjust the door height.

5.Replace the locking plate.

6.Turn the bushing slightly to align the hinge and locking plate screw holes.

7.Replace the door stop screw or screws and tighten.

IMPORTANT: Do not place the door stop screw in the 130° position on Overlay Series models unless the custom panels have been routed on the hinge side. See “Overlay Series Door Panel & Cabinetry Clearance.”

8.Make final recheck to make sure the doors are aligned and even.

Door Swing Adjustment

1.Check that the refrigerator door can open freely. If the door opens too wide, remove the door stop screw or screws (depending on your model) from the bottom hinge. See “Door Height Adjustment” earlier in this section.

2.Hold the door open to a position that is less than 90°.

3.Replace the door stop screw or screws in the bottom hinge and tighten.

A B C

A.130°

B.110° (Overlay series)

C.90°

Door-to-Door or Door-to-Refrigerator Trim Adjustment

1.Loosen, but do not remove, the four Torx®† 27 flat-head mounting screws and the two ¹⁄₄" hex-head mounting screws.

2.Adjust the top hinge of either door to align it with the other door or the refrigerator trim.

3.Tighten the four Torx®† 27 flat-head mounting screws to a torque of approximately 100 inch-pounds (11.3 Nm) and tighten the two ¹⁄₄" hex-head mounting screws.

A

B

A.Torx® 27 flat-head mounting screws

B.¹⁄₄" hex-head mounting screws

†®TORX is a registered trademark of Textron Innovations Inc.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorTable of Contents ÍndiceTable DES Matières Refrigerator Safety Your safety and the safety of others are very importantModels Side by Side Non-Dispensing RefrigeratorsArchitect Series Classic SeriesSide by Side Dispensing Refrigerators Complete SeriesInstallation Requirements Opening DimensionsToolsand Parts Location RequirementsElectrical Requirements Recommended Grounding MethodModel Width a as shown above Water Supply Requirements Tipping RadiusWater Pressure Reverse Osmosis Water SupplyProductDimensions Side View Front ViewTop View Model Width a Trim edge to trim edgeDoor SwingDimensions 36 91.4 cm Models42 106.7 cm Models 48 121.9 cm ModelsOverlay Panel Overlay SeriesDoor Panel & CabinetryClearanceOverlayPanel OverlaySeries Custom Panelsand Handle Kits Decorative Overlay Panels ModelBacker Panels Model Classic SeriesFactory Panelsand Kits ClassicSeries Custom Panels Door Panels for Dispenser ModelsTop Grille Panel Door Panels for Non-dispenser ModelsRefrigerator and Side Trim Dimensions Classic, Architect and Complete Series Custom Side PanelsDoor Panels Routing Requirements RefrigeratorRefrigerator Inset Installation Dimensions Flush Installation DimensionsRecessed Inset Installation Dimensions OverlaySeries Custom Side PanelsInstallation Instructions Unpack the RefrigeratorReduce TippingRadius Measure the distance from point a as shown to back wallInstall Anti-Tip Boards To Install Anti-tip BoardsMove the Refrigerator into House Connectthe Water SupplyStyle 2 Copper Line Connection Connecting to Water Line Connecting to RefrigeratorPlug in Refrigerator MoveRefrigerator toFinal LocationLevel and Align Refrigerator Install ClassicSeries Custom Panels Check refrigerator level and adjustment. Adjust if neededDoor Panels Install OverlaySeries Custom Panels Door Panel InstallationAdjust Doors Door Height AdjustmentDoor Swing Adjustment Door-to-Door or Door-to-Refrigerator Trim AdjustmentInstall Side Panel Install Base GrilleSnap the skirt onto the base grille Complete Installation Water System PreparationStyle 1 Non-Dispenser Models Style 2 Dispenser Models Page Seguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteModelos Refrigeradores de dos puertas sin despachadorSerie Architect Serie ClassicRefrigeradores de dos puertas con despachador Serie CompletaRequisitos DE Instalación Piezas y herramientasRequisitosde ubicación Medidas de la aberturaRequisitoseléctricos Método de conexión a tierra recomendadoModelo Ancho a Como se muestra anteriormente Requisitosdel suministro de agua Arco devuelcoPresión del agua Suministro de agua de ósmosis inversaMedidas delproducto Vista lateral Vista frontalVista superior Modelo Ancho aMedidas de oscilación de las puertas Modelos de 36 91,4 cmModelos de 42 106,7 cm Modelos de 48 121,9 cmPuerta Panel Paneles decorativos recubiertos Modelo Paneles de soporte ModeloPaneles y juegos de fábrica delaserie Classic Panelesa la medida para la serie Classic Paneles de puerta para modelos con despachadorPanel de la rejilla superior Paneles de puerta para modelos sin despachadorRequisitos de contorneado de los paneles de la puerta Medidas del refrigerador y del adorno lateralRefrigerador Agarradera extendida Vista superiorPaneles laterales a la medida para la Serie Overlay Adornos lateralesMedidas para la instalación empotrada Medidas para la instalación al rasInstrucciones DE Instalación Desempaque el refrigeradorCómoreducirelarco de vuelco Modelo Arco de vuelco reducidoCómo instalarlos tablerosantivuelco Cómo instalar los tableros antivuelcoConexión del suministro de agua Estilo 1 Conexión de la válvula de cierreConexión al refrigerador Lea todas las instrucciones antes de comenzarCómo enchufar elrefrigerador Cómo mover el refrigerador a su ubicación FinalNivelación yalineamientodel refrigerador Cómo instalar los paneles a la medida para la Serie Classic Paneles de la puertaInstalación del panel de la puerta Ajuste laspuertas Cómo ajustar la altura de la puertaCómo ajustar la oscilación de las puertas Modelos Classic y ArchitectCómoinstalar el panellateral Cómo instalar la rejilla de la baseCómoterminarla instalación Preparación del sistema de aguaSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteModèles Réfrigérateurs côte à côte sans distributeurSérie Architect Série ClassicRéfrigérateurs côte à côte avec distributeur Série ComplèteExigences D’INSTALLATION Exigences d’emplacementDimensions de l’ouverture Outillage etpiècesMéthode recommandée de mise à la terre SpécificationsélectriquesModèle Largeur a tel quillustré ci-dessus Spécifications de l’alimentation en eau Rayon debasculementPression de leau Alimentation en eau par osmose inverseDimensions du produit Vue latérale Vue avantVue de dessus Modèle Largeur aDimensionspour le pivotement desportes Modèles de 36 91,4 cmModèles de 42 106,7 cm Modèles de 48 121,9 cmPorte Panneau Charnière Porte Panneaux personnalisés et poignéesde la série Overlay Panneau décoratif Overlay ModèlePanneau d’appui Modèle Ensemblesde panneaux dorigine de la série Classic Panneaux personnalisés de la Série Classic Panneaux de porte pour modèles avec distributeurPanneau de la grille supérieure Panneaux de porte pour modèles sans distributeurDimensions du réfrigérateur et des garnitures latérales Exigences dusinage des panneaux de porteRéfrigérateur Poignée de porte prolongée Vue supérieureDimensions pour un panneau inséré Dimensions pour un panneau en affleurementDimensions pour un panneau inséré en retrait Panneaux latéraux personnalisés de la Série OverlayInstructions D’INSTALLATION Déballage du réfrigérateurRéduction du rayon de basculement Modèle Rayon de basculement réduitInstallation de planchesantibasculement Installation des planches antibasculementFaire entrerle réfrigérateur dans le domicile Raccordementà la canalisation deau Style 1 Raccordement sur robinet darrêtRaccordement au réfrigérateur Ouvrir le robinet darrêtDéplacementdu réfrigérateur à Lemplacement final Brancher le réfrigérateurRéglage de laplomb etalignement du Réfrigérateur Installation despanneaux personnalisés De la Série Classic Panneaux de porteInstallation despanneaux personnalisés De la Série Overlay Installation des panneaux de porteAjustement desportes Ajustement de la hauteur des portesAjustement du pivotement des portes Modèles Classic et ArchitectInstallation du panneau latéral Installation de la grille de la baseAcheverl’installation Préparation du système d’eauVeuillez lire avant d’utiliser le système d’eau Style 1 Modèles sans distributeur2316565B All rights reserved

2316565B specifications

The KitchenAid 2316565B is a versatile and powerful kitchen appliance that enhances the cooking experience for home chefs and baking enthusiasts alike. Known for its durable construction and innovative features, this stand mixer is a must-have tool in any modern kitchen.

One of the standout features of the KitchenAid 2316565B is its robust 325-watt motor. This powerful motor ensures that the mixer can handle a variety of tasks, from kneading dense bread dough to whipping egg whites into fluffy peaks. The mixer operates with a reliable planetary mixing action, which means that the bowl and the beater rotate in opposite directions, ensuring that all ingredients are mixed thoroughly and evenly.

The KitchenAid 2316565B boasts a large capacity bowl that can hold up to 5 quarts. This generous size allows for mixing large batches of dough or batter, making it ideal for large families or entertaining guests. The stainless steel bowl is not only sturdy but also comes with a comfortable handle and is dishwasher safe, making cleanup a breeze.

Another impressive feature of this stand mixer is its 10-speed screw control. This allows users to easily adjust the mixing speed for various tasks, from slow stirring to fast whipping. The precision of the speed settings ensures that users can achieve the perfect consistency for every recipe.

KitchenAid has also designed the 2316565B with a tilt-head mechanism. This thoughtful design allows for easy access to the mixing bowl and makes it simple to add ingredients while the mixer is in operation. The mixer comes with a range of accessories, including a flat beater, a dough hook, and a wire whip, catering to different mixing needs and recipes.

In addition to its functionality, the KitchenAid 2316565B is available in a variety of colors, allowing users to choose one that fits their kitchen aesthetic. The mixer's classic design and robust performance make it not only a practical kitchen tool but also a stylish addition to any countertop.

Overall, the KitchenAid 2316565B stand mixer is a reliable, efficient, and aesthetically pleasing appliance that provides an enjoyable cooking experience. Whether you're a beginner in the kitchen or a seasoned chef, this stand mixer is designed to meet all your mixing, kneading, and whipping needs, making it a valuable addition to any home.
Top Page Image Contents