KitchenAid 2316565B manual Install ClassicSeries Custom Panels, Door Panels

Page 22

3.Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1" (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within ¹⁄₄" (6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover.

A B

C

¹⁄₄" (6 mm) max.

2" (5 cm)

D

A. Center board ¹⁄₄" (6.35 mm) max. above refrigerator

B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch- pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers.

4.For Classic and Overlay models, additional adjustments may be needed after the custom panels are installed.

4.If needed, route the door panels or install a filler panel between the doors and the decorative panels. See the “Classic Series Custom Panels” section in “Installation Requirements.”

AA

A.Panels

5.Replace the door handles. Install the top screw on each handle first. Be sure that the top of both door handles are aligned.

6.If the door handles are not aligned, loosen all handle screws and adjust door handles up or down. Tighten the screws.

7.Check refrigerator level and adjustment. Adjust if needed.

Top Grille Panel

1.Grasp both ends of the top grille.

2.Push straight up, then pull straight out. Place the top grille panel-side down on a soft working surface.

BAB

Install ClassicSeries Custom Panels

IMPORTANT: KitchenAid is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator for service.

Door Panels

1.Remove all tape and door bracing from the refrigerator and freezer doors.

2.Remove the screws that attach the handles to the door frame.

3.Slide the decorative door panels into the door frames.

A. Top grille

B. Cabinet side trim

3.Remove one end cap by loosening the nuts and sliding off the end cap.

A

 

C

 

B

 

D

 

A. Bottom rail

C. End cap

B. Nuts

D. Top rail

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorÍndice Table of ContentsTable DES Matières Refrigerator Safety Your safety and the safety of others are very importantArchitect Series ModelsSide by Side Non-Dispensing Refrigerators Classic SeriesSide by Side Dispensing Refrigerators Complete SeriesToolsand Parts Installation RequirementsOpening Dimensions Location RequirementsRecommended Grounding Method Electrical RequirementsModel Width a as shown above Water Pressure Water Supply RequirementsTipping Radius Reverse Osmosis Water SupplyTop View ProductDimensionsSide View Front View Model Width a Trim edge to trim edge42 106.7 cm Models Door SwingDimensions36 91.4 cm Models 48 121.9 cm ModelsOverlay Panel Overlay SeriesDoor Panel & CabinetryClearanceOverlayPanel Decorative Overlay Panels Model OverlaySeries Custom Panelsand Handle KitsBacker Panels Model Classic SeriesFactory Panelsand Kits Top Grille Panel ClassicSeries Custom PanelsDoor Panels for Dispenser Models Door Panels for Non-dispenser ModelsDoor Panels Routing Requirements Refrigerator and Side Trim DimensionsClassic, Architect and Complete Series Custom Side Panels RefrigeratorRecessed Inset Installation Dimensions Refrigerator Inset Installation DimensionsFlush Installation Dimensions OverlaySeries Custom Side PanelsReduce TippingRadius Installation InstructionsUnpack the Refrigerator Measure the distance from point a as shown to back wallMove the Refrigerator into House Install Anti-Tip BoardsTo Install Anti-tip Boards Connectthe Water SupplyStyle 2 Copper Line Connection Connecting to Water Line Connecting to RefrigeratorMoveRefrigerator toFinal Location Plug in RefrigeratorLevel and Align Refrigerator Check refrigerator level and adjustment. Adjust if needed Install ClassicSeries Custom PanelsDoor Panels Install OverlaySeries Custom Panels Door Panel InstallationDoor Swing Adjustment Adjust DoorsDoor Height Adjustment Door-to-Door or Door-to-Refrigerator Trim AdjustmentInstall Base Grille Install Side PanelSnap the skirt onto the base grille Water System Preparation Complete InstallationStyle 1 Non-Dispenser Models Style 2 Dispenser Models Page Seguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteSerie Architect ModelosRefrigeradores de dos puertas sin despachador Serie ClassicRefrigeradores de dos puertas con despachador Serie CompletaRequisitosde ubicación Requisitos DE InstalaciónPiezas y herramientas Medidas de la aberturaMétodo de conexión a tierra recomendado RequisitoseléctricosModelo Ancho a Como se muestra anteriormente Presión del agua Requisitosdel suministro de aguaArco devuelco Suministro de agua de ósmosis inversaVista superior Medidas delproductoVista lateral Vista frontal Modelo Ancho aModelos de 42 106,7 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 48 121,9 cmPuerta Panel Paneles decorativos recubiertos Modelo Paneles de soporte ModeloPaneles y juegos de fábrica delaserie Classic Panel de la rejilla superior Panelesa la medida para la serie ClassicPaneles de puerta para modelos con despachador Paneles de puerta para modelos sin despachadorRefrigerador Requisitos de contorneado de los paneles de la puertaMedidas del refrigerador y del adorno lateral Agarradera extendida Vista superiorMedidas para la instalación empotrada Paneles laterales a la medida para la Serie OverlayAdornos laterales Medidas para la instalación al rasCómoreducirelarco de vuelco Instrucciones DE InstalaciónDesempaque el refrigerador Modelo Arco de vuelco reducidoCómo instalarlos tablerosantivuelco Cómo instalar los tableros antivuelcoConexión al refrigerador Conexión del suministro de aguaEstilo 1 Conexión de la válvula de cierre Lea todas las instrucciones antes de comenzarCómo mover el refrigerador a su ubicación Final Cómo enchufar elrefrigeradorNivelación yalineamientodel refrigerador Cómo instalar los paneles a la medida para la Serie Classic Paneles de la puertaInstalación del panel de la puerta Cómo ajustar la oscilación de las puertas Ajuste laspuertasCómo ajustar la altura de la puerta Modelos Classic y ArchitectCómoinstalar el panellateral Cómo instalar la rejilla de la baseCómoterminarla instalación Preparación del sistema de aguaSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteSérie Architect ModèlesRéfrigérateurs côte à côte sans distributeur Série ClassicRéfrigérateurs côte à côte avec distributeur Série ComplèteDimensions de l’ouverture Exigences D’INSTALLATIONExigences d’emplacement Outillage etpiècesSpécificationsélectriques Méthode recommandée de mise à la terreModèle Largeur a tel quillustré ci-dessus Pression de leau Spécifications de l’alimentation en eauRayon debasculement Alimentation en eau par osmose inverseVue de dessus Dimensions du produitVue latérale Vue avant Modèle Largeur aModèles de 42 106,7 cm Dimensionspour le pivotement desportesModèles de 36 91,4 cm Modèles de 48 121,9 cmPorte Panneau Charnière Porte Panneau décoratif Overlay Modèle Panneaux personnalisés et poignéesde la série OverlayPanneau d’appui Modèle Ensemblesde panneaux dorigine de la série Classic Panneau de la grille supérieure Panneaux personnalisés de la Série ClassicPanneaux de porte pour modèles avec distributeur Panneaux de porte pour modèles sans distributeurRéfrigérateur Dimensions du réfrigérateur et des garnitures latéralesExigences dusinage des panneaux de porte Poignée de porte prolongée Vue supérieureDimensions pour un panneau inséré en retrait Dimensions pour un panneau inséréDimensions pour un panneau en affleurement Panneaux latéraux personnalisés de la Série OverlayRéduction du rayon de basculement Instructions D’INSTALLATIONDéballage du réfrigérateur Modèle Rayon de basculement réduitInstallation des planches antibasculement Installation de planchesantibasculementFaire entrerle réfrigérateur dans le domicile Raccordement au réfrigérateur Raccordementà la canalisation deauStyle 1 Raccordement sur robinet darrêt Ouvrir le robinet darrêtBrancher le réfrigérateur Déplacementdu réfrigérateur à Lemplacement finalRéglage de laplomb etalignement du Réfrigérateur Installation despanneaux personnalisés De la Série Classic Panneaux de porteInstallation despanneaux personnalisés De la Série Overlay Installation des panneaux de porteAjustement du pivotement des portes Ajustement desportesAjustement de la hauteur des portes Modèles Classic et ArchitectInstallation du panneau latéral Installation de la grille de la baseVeuillez lire avant d’utiliser le système d’eau Acheverl’installationPréparation du système d’eau Style 1 Modèles sans distributeur2316565B All rights reserved

2316565B specifications

The KitchenAid 2316565B is a versatile and powerful kitchen appliance that enhances the cooking experience for home chefs and baking enthusiasts alike. Known for its durable construction and innovative features, this stand mixer is a must-have tool in any modern kitchen.

One of the standout features of the KitchenAid 2316565B is its robust 325-watt motor. This powerful motor ensures that the mixer can handle a variety of tasks, from kneading dense bread dough to whipping egg whites into fluffy peaks. The mixer operates with a reliable planetary mixing action, which means that the bowl and the beater rotate in opposite directions, ensuring that all ingredients are mixed thoroughly and evenly.

The KitchenAid 2316565B boasts a large capacity bowl that can hold up to 5 quarts. This generous size allows for mixing large batches of dough or batter, making it ideal for large families or entertaining guests. The stainless steel bowl is not only sturdy but also comes with a comfortable handle and is dishwasher safe, making cleanup a breeze.

Another impressive feature of this stand mixer is its 10-speed screw control. This allows users to easily adjust the mixing speed for various tasks, from slow stirring to fast whipping. The precision of the speed settings ensures that users can achieve the perfect consistency for every recipe.

KitchenAid has also designed the 2316565B with a tilt-head mechanism. This thoughtful design allows for easy access to the mixing bowl and makes it simple to add ingredients while the mixer is in operation. The mixer comes with a range of accessories, including a flat beater, a dough hook, and a wire whip, catering to different mixing needs and recipes.

In addition to its functionality, the KitchenAid 2316565B is available in a variety of colors, allowing users to choose one that fits their kitchen aesthetic. The mixer's classic design and robust performance make it not only a practical kitchen tool but also a stylish addition to any countertop.

Overall, the KitchenAid 2316565B stand mixer is a reliable, efficient, and aesthetically pleasing appliance that provides an enjoyable cooking experience. Whether you're a beginner in the kitchen or a seasoned chef, this stand mixer is designed to meet all your mixing, kneading, and whipping needs, making it a valuable addition to any home.
Top Page Image Contents