KitchenAid 2316565B manual Complete Installation, Water System Preparation

Page 26

Complete Installation

1.Turn the water supply line valve to the “Open” position.

2.Turn the refrigerator switch to the ON position. See “Power On/Off Switch” in the Use & Care Guide for instructions. Wait a few minutes. Check the water line connections for leaks.

3.Remove all boxes, parts packages and packing materials from the interior of the refrigerator. See the “Cleaning” section in the Use & Care Guide for instructions. Remove the protective film and cardboard from the grille and doors or door frame, depending on your model.

4.Install the shelves and bins in the refrigerator and freezer compartments.

5.The controls are preset at the factory to the midpoint setting. Check to be sure that the compressor is operating properly and that all the lights are working.

6.Flush the water system before use. See “Water System Preparation.”

To get the most efficient use from your new built-in refrigerator, read your Use & Care Guide. Keep Installation Instructions and Use & Care Guide near the built-in refrigerator for easy reference.

Water System Preparation

Please read before using the water system.

Immediately after installation, follow the steps below to make sure that the water system is properly cleaned.

1.Open the freezer door and turn off the ice maker. For Style 1, lift up the wire shutoff arm as shown. For Style 2, move the switch to the OFF (right) setting as shown. The On/Off switch is located on the top right side of the freezer compartment.

Style 1 – Non-Dispenser Models

Style 2 – Dispenser Models

NOTE: If your model has a base grille filter system, make sure the base grille filter is properly installed and the cap is in the horizontal position.

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.

2.Use a sturdy container to depress and hold the water dispenser lever for 5 seconds, then release it for 5 seconds. Repeat until water begins to flow. Once water begins to flow, continue depressing and releasing the dispenser lever

(5 seconds on, 5 seconds off) for an additional 2 minutes. This will flush air from the filter and water dispensing system. Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of the dispenser.

3.Open the freezer door and turn on the ice maker. For Style 1, lower the wire shutoff arm. For Style 2, move the switch to the ON (left) position.

■Allow 24 hours to produce the first batch of ice.

■Discard the first three batches of ice produced.

■Depending on your model, you may want to select the maximum ice feature to increase the production of ice.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Table of Contents/Índice/Table des matières Side by Side BUILT-IN RefrigeratorTable DES Matières Table of ContentsÍndice Refrigerator Safety Your safety and the safety of others are very importantArchitect Series ModelsSide by Side Non-Dispensing Refrigerators Classic SeriesSide by Side Dispensing Refrigerators Complete SeriesToolsand Parts Installation RequirementsOpening Dimensions Location RequirementsModel Width a as shown above Electrical RequirementsRecommended Grounding Method Water Pressure Water Supply RequirementsTipping Radius Reverse Osmosis Water SupplyTop View ProductDimensionsSide View Front View Model Width a Trim edge to trim edge42 106.7 cm Models Door SwingDimensions36 91.4 cm Models 48 121.9 cm ModelsOverlay Panel Overlay SeriesDoor Panel & CabinetryClearanceOverlayPanel Backer Panels Model OverlaySeries Custom Panelsand Handle KitsDecorative Overlay Panels Model Classic SeriesFactory Panelsand Kits Top Grille Panel ClassicSeries Custom PanelsDoor Panels for Dispenser Models Door Panels for Non-dispenser ModelsDoor Panels Routing Requirements Refrigerator and Side Trim DimensionsClassic, Architect and Complete Series Custom Side Panels RefrigeratorRecessed Inset Installation Dimensions Refrigerator Inset Installation DimensionsFlush Installation Dimensions OverlaySeries Custom Side PanelsReduce TippingRadius Installation InstructionsUnpack the Refrigerator Measure the distance from point a as shown to back wallMove the Refrigerator into House Install Anti-Tip BoardsTo Install Anti-tip Boards Connectthe Water SupplyStyle 2 Copper Line Connection Connecting to Water Line Connecting to RefrigeratorLevel and Align Refrigerator Plug in RefrigeratorMoveRefrigerator toFinal Location Door Panels Install ClassicSeries Custom PanelsCheck refrigerator level and adjustment. Adjust if needed Install OverlaySeries Custom Panels Door Panel InstallationDoor Swing Adjustment Adjust DoorsDoor Height Adjustment Door-to-Door or Door-to-Refrigerator Trim AdjustmentSnap the skirt onto the base grille Install Side PanelInstall Base Grille Style 1 Non-Dispenser Models Style 2 Dispenser Models Complete InstallationWater System Preparation Page Seguridad DEL Refrigerador Su seguridad y la seguridad de los demás es muy importanteSerie Architect ModelosRefrigeradores de dos puertas sin despachador Serie ClassicRefrigeradores de dos puertas con despachador Serie CompletaRequisitosde ubicación Requisitos DE InstalaciónPiezas y herramientas Medidas de la aberturaModelo Ancho a Como se muestra anteriormente RequisitoseléctricosMétodo de conexión a tierra recomendado Presión del agua Requisitosdel suministro de aguaArco devuelco Suministro de agua de ósmosis inversaVista superior Medidas delproductoVista lateral Vista frontal Modelo Ancho aModelos de 42 106,7 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 48 121,9 cmPuerta Panel Paneles decorativos recubiertos Modelo Paneles de soporte ModeloPaneles y juegos de fábrica delaserie Classic Panel de la rejilla superior Panelesa la medida para la serie ClassicPaneles de puerta para modelos con despachador Paneles de puerta para modelos sin despachadorRefrigerador Requisitos de contorneado de los paneles de la puertaMedidas del refrigerador y del adorno lateral Agarradera extendida Vista superiorMedidas para la instalación empotrada Paneles laterales a la medida para la Serie OverlayAdornos laterales Medidas para la instalación al rasCómoreducirelarco de vuelco Instrucciones DE InstalaciónDesempaque el refrigerador Modelo Arco de vuelco reducidoCómo instalarlos tablerosantivuelco Cómo instalar los tableros antivuelcoConexión al refrigerador Conexión del suministro de aguaEstilo 1 Conexión de la válvula de cierre Lea todas las instrucciones antes de comenzarNivelación yalineamientodel refrigerador Cómo enchufar elrefrigeradorCómo mover el refrigerador a su ubicación Final Cómo instalar los paneles a la medida para la Serie Classic Paneles de la puertaInstalación del panel de la puerta Cómo ajustar la oscilación de las puertas Ajuste laspuertasCómo ajustar la altura de la puerta Modelos Classic y ArchitectCómoinstalar el panellateral Cómo instalar la rejilla de la baseCómoterminarla instalación Preparación del sistema de aguaSécurité DU Réfrigérateur Votre sécurité et celle des autres est très importanteSérie Architect ModèlesRéfrigérateurs côte à côte sans distributeur Série ClassicRéfrigérateurs côte à côte avec distributeur Série ComplèteDimensions de l’ouverture Exigences D’INSTALLATIONExigences d’emplacement Outillage etpiècesModèle Largeur a tel quillustré ci-dessus Méthode recommandée de mise à la terreSpécificationsélectriques Pression de leau Spécifications de l’alimentation en eauRayon debasculement Alimentation en eau par osmose inverseVue de dessus Dimensions du produitVue latérale Vue avant Modèle Largeur aModèles de 42 106,7 cm Dimensionspour le pivotement desportesModèles de 36 91,4 cm Modèles de 48 121,9 cmPorte Panneau Charnière Porte Panneau d’appui Modèle Panneaux personnalisés et poignéesde la série OverlayPanneau décoratif Overlay Modèle Ensemblesde panneaux dorigine de la série Classic Panneau de la grille supérieure Panneaux personnalisés de la Série ClassicPanneaux de porte pour modèles avec distributeur Panneaux de porte pour modèles sans distributeurRéfrigérateur Dimensions du réfrigérateur et des garnitures latéralesExigences dusinage des panneaux de porte Poignée de porte prolongée Vue supérieureDimensions pour un panneau inséré en retrait Dimensions pour un panneau inséréDimensions pour un panneau en affleurement Panneaux latéraux personnalisés de la Série OverlayRéduction du rayon de basculement Instructions D’INSTALLATIONDéballage du réfrigérateur Modèle Rayon de basculement réduitFaire entrerle réfrigérateur dans le domicile Installation de planchesantibasculementInstallation des planches antibasculement Raccordement au réfrigérateur Raccordementà la canalisation deauStyle 1 Raccordement sur robinet darrêt Ouvrir le robinet darrêtRéglage de laplomb etalignement du Réfrigérateur Déplacementdu réfrigérateur à Lemplacement finalBrancher le réfrigérateur Installation despanneaux personnalisés De la Série Classic Panneaux de porteInstallation despanneaux personnalisés De la Série Overlay Installation des panneaux de porteAjustement du pivotement des portes Ajustement desportesAjustement de la hauteur des portes Modèles Classic et ArchitectInstallation du panneau latéral Installation de la grille de la baseVeuillez lire avant d’utiliser le système d’eau Acheverl’installationPréparation du système d’eau Style 1 Modèles sans distributeur2316565B All rights reserved

2316565B specifications

The KitchenAid 2316565B is a versatile and powerful kitchen appliance that enhances the cooking experience for home chefs and baking enthusiasts alike. Known for its durable construction and innovative features, this stand mixer is a must-have tool in any modern kitchen.

One of the standout features of the KitchenAid 2316565B is its robust 325-watt motor. This powerful motor ensures that the mixer can handle a variety of tasks, from kneading dense bread dough to whipping egg whites into fluffy peaks. The mixer operates with a reliable planetary mixing action, which means that the bowl and the beater rotate in opposite directions, ensuring that all ingredients are mixed thoroughly and evenly.

The KitchenAid 2316565B boasts a large capacity bowl that can hold up to 5 quarts. This generous size allows for mixing large batches of dough or batter, making it ideal for large families or entertaining guests. The stainless steel bowl is not only sturdy but also comes with a comfortable handle and is dishwasher safe, making cleanup a breeze.

Another impressive feature of this stand mixer is its 10-speed screw control. This allows users to easily adjust the mixing speed for various tasks, from slow stirring to fast whipping. The precision of the speed settings ensures that users can achieve the perfect consistency for every recipe.

KitchenAid has also designed the 2316565B with a tilt-head mechanism. This thoughtful design allows for easy access to the mixing bowl and makes it simple to add ingredients while the mixer is in operation. The mixer comes with a range of accessories, including a flat beater, a dough hook, and a wire whip, catering to different mixing needs and recipes.

In addition to its functionality, the KitchenAid 2316565B is available in a variety of colors, allowing users to choose one that fits their kitchen aesthetic. The mixer's classic design and robust performance make it not only a practical kitchen tool but also a stylish addition to any countertop.

Overall, the KitchenAid 2316565B stand mixer is a reliable, efficient, and aesthetically pleasing appliance that provides an enjoyable cooking experience. Whether you're a beginner in the kitchen or a seasoned chef, this stand mixer is designed to meet all your mixing, kneading, and whipping needs, making it a valuable addition to any home.
Top Page Image Contents