KitchenAid 2316565B manual Electrical Requirements, Recommended Grounding Method

Page 7

■A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right side cabinets or end panel. See “Electrical Requirements” for more information.

■The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See “Water Supply Requirements” for more information.

 

80" - 90"

 

 

(203-229 cm)

4"

 

 

 

 

(10.2 cm)

83¹⁄₂" (212.1 cm) min.

 

84³⁄₄" (215 cm) max.

 

to bottom of solid soffit

 

 

 

77"

 

 

(196 cm)

 

A

 

 

Width

 

 

(see chart following)

 

 

 

6"

 

 

(15.2 cm)

 

1"

 

6"

(2.54 cm)

6"

(15.2 cm)

(15.2 cm)

 

24"

 

 

(60.96 cm) min.

 

Model Width A (as shown above)

3635¹⁄₂" (90.2 cm) to 35³⁄₄" (90.8 cm)

4241¹⁄₂" (105.4 cm) to 41³⁄₄" (106.1 cm)

4847¹⁄₂" (120.7 cm) to 47³⁄₄" (121.3 cm)

NOTE: Flooring under refrigerator must be at same level as the room. Face of cabinetry must be plumb.

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker box.

When you are finished, turn ON the master power switch or reconnect power at the circuit breaker box. Then reset the control to the desired setting.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Side by Side BUILT-IN Refrigerator Table of Contents/Índice/Table des matièresÍndice Table of ContentsTable DES Matières Your safety and the safety of others are very important Refrigerator SafetyClassic Series ModelsSide by Side Non-Dispensing Refrigerators Architect SeriesComplete Series Side by Side Dispensing RefrigeratorsLocation Requirements Installation RequirementsOpening Dimensions Toolsand PartsRecommended Grounding Method Electrical RequirementsModel Width a as shown above Reverse Osmosis Water Supply Water Supply RequirementsTipping Radius Water PressureModel Width a Trim edge to trim edge ProductDimensionsSide View Front View Top View48 121.9 cm Models Door SwingDimensions36 91.4 cm Models 42 106.7 cm ModelsOverlay SeriesDoor Panel & CabinetryClearance Overlay PanelOverlayPanel Decorative Overlay Panels Model OverlaySeries Custom Panelsand Handle KitsBacker Panels Model Classic SeriesFactory Panelsand Kits Door Panels for Non-dispenser Models ClassicSeries Custom PanelsDoor Panels for Dispenser Models Top Grille PanelRefrigerator Refrigerator and Side Trim DimensionsClassic, Architect and Complete Series Custom Side Panels Door Panels Routing RequirementsOverlaySeries Custom Side Panels Refrigerator Inset Installation DimensionsFlush Installation Dimensions Recessed Inset Installation DimensionsMeasure the distance from point a as shown to back wall Installation InstructionsUnpack the Refrigerator Reduce TippingRadiusConnectthe Water Supply Install Anti-Tip BoardsTo Install Anti-tip Boards Move the Refrigerator into HouseConnecting to Refrigerator Style 2 Copper Line Connection Connecting to Water LineMoveRefrigerator toFinal Location Plug in RefrigeratorLevel and Align Refrigerator Check refrigerator level and adjustment. Adjust if needed Install ClassicSeries Custom PanelsDoor Panels Door Panel Installation Install OverlaySeries Custom PanelsDoor-to-Door or Door-to-Refrigerator Trim Adjustment Adjust DoorsDoor Height Adjustment Door Swing AdjustmentInstall Base Grille Install Side PanelSnap the skirt onto the base grille Water System Preparation Complete InstallationStyle 1 Non-Dispenser Models Style 2 Dispenser Models Page Su seguridad y la seguridad de los demás es muy importante Seguridad DEL RefrigeradorSerie Classic ModelosRefrigeradores de dos puertas sin despachador Serie ArchitectSerie Completa Refrigeradores de dos puertas con despachadorMedidas de la abertura Requisitos DE InstalaciónPiezas y herramientas Requisitosde ubicaciónMétodo de conexión a tierra recomendado RequisitoseléctricosModelo Ancho a Como se muestra anteriormente Suministro de agua de ósmosis inversa Requisitosdel suministro de aguaArco devuelco Presión del aguaModelo Ancho a Medidas delproductoVista lateral Vista frontal Vista superiorModelos de 48 121,9 cm Medidas de oscilación de las puertasModelos de 36 91,4 cm Modelos de 42 106,7 cmPuerta Panel Paneles de soporte Modelo Paneles decorativos recubiertos ModeloPaneles y juegos de fábrica delaserie Classic Paneles de puerta para modelos sin despachador Panelesa la medida para la serie ClassicPaneles de puerta para modelos con despachador Panel de la rejilla superiorAgarradera extendida Vista superior Requisitos de contorneado de los paneles de la puertaMedidas del refrigerador y del adorno lateral RefrigeradorMedidas para la instalación al ras Paneles laterales a la medida para la Serie OverlayAdornos laterales Medidas para la instalación empotradaModelo Arco de vuelco reducido Instrucciones DE InstalaciónDesempaque el refrigerador Cómoreducirelarco de vuelcoCómo instalar los tableros antivuelco Cómo instalarlos tablerosantivuelcoLea todas las instrucciones antes de comenzar Conexión del suministro de aguaEstilo 1 Conexión de la válvula de cierre Conexión al refrigeradorCómo mover el refrigerador a su ubicación Final Cómo enchufar elrefrigeradorNivelación yalineamientodel refrigerador Paneles de la puerta Cómo instalar los paneles a la medida para la Serie ClassicInstalación del panel de la puerta Modelos Classic y Architect Ajuste laspuertasCómo ajustar la altura de la puerta Cómo ajustar la oscilación de las puertasCómo instalar la rejilla de la base Cómoinstalar el panellateralPreparación del sistema de agua Cómoterminarla instalaciónVotre sécurité et celle des autres est très importante Sécurité DU RéfrigérateurSérie Classic ModèlesRéfrigérateurs côte à côte sans distributeur Série ArchitectSérie Complète Réfrigérateurs côte à côte avec distributeurOutillage etpièces Exigences D’INSTALLATIONExigences d’emplacement Dimensions de l’ouvertureSpécificationsélectriques Méthode recommandée de mise à la terreModèle Largeur a tel quillustré ci-dessus Alimentation en eau par osmose inverse Spécifications de l’alimentation en eauRayon debasculement Pression de leauModèle Largeur a Dimensions du produitVue latérale Vue avant Vue de dessusModèles de 48 121,9 cm Dimensionspour le pivotement desportesModèles de 36 91,4 cm Modèles de 42 106,7 cmPorte Panneau Charnière Porte Panneau décoratif Overlay Modèle Panneaux personnalisés et poignéesde la série OverlayPanneau d’appui Modèle Ensemblesde panneaux dorigine de la série Classic Panneaux de porte pour modèles sans distributeur Panneaux personnalisés de la Série ClassicPanneaux de porte pour modèles avec distributeur Panneau de la grille supérieurePoignée de porte prolongée Vue supérieure Dimensions du réfrigérateur et des garnitures latéralesExigences dusinage des panneaux de porte RéfrigérateurPanneaux latéraux personnalisés de la Série Overlay Dimensions pour un panneau inséréDimensions pour un panneau en affleurement Dimensions pour un panneau inséré en retraitModèle Rayon de basculement réduit Instructions D’INSTALLATIONDéballage du réfrigérateur Réduction du rayon de basculementInstallation des planches antibasculement Installation de planchesantibasculementFaire entrerle réfrigérateur dans le domicile Ouvrir le robinet darrêt Raccordementà la canalisation deauStyle 1 Raccordement sur robinet darrêt Raccordement au réfrigérateurBrancher le réfrigérateur Déplacementdu réfrigérateur à Lemplacement finalRéglage de laplomb etalignement du Réfrigérateur Panneaux de porte Installation despanneaux personnalisés De la Série ClassicInstallation des panneaux de porte Installation despanneaux personnalisés De la Série OverlayModèles Classic et Architect Ajustement desportesAjustement de la hauteur des portes Ajustement du pivotement des portesInstallation de la grille de la base Installation du panneau latéralStyle 1 Modèles sans distributeur Acheverl’installationPréparation du système d’eau Veuillez lire avant d’utiliser le système d’eauAll rights reserved 2316565B

2316565B specifications

The KitchenAid 2316565B is a versatile and powerful kitchen appliance that enhances the cooking experience for home chefs and baking enthusiasts alike. Known for its durable construction and innovative features, this stand mixer is a must-have tool in any modern kitchen.

One of the standout features of the KitchenAid 2316565B is its robust 325-watt motor. This powerful motor ensures that the mixer can handle a variety of tasks, from kneading dense bread dough to whipping egg whites into fluffy peaks. The mixer operates with a reliable planetary mixing action, which means that the bowl and the beater rotate in opposite directions, ensuring that all ingredients are mixed thoroughly and evenly.

The KitchenAid 2316565B boasts a large capacity bowl that can hold up to 5 quarts. This generous size allows for mixing large batches of dough or batter, making it ideal for large families or entertaining guests. The stainless steel bowl is not only sturdy but also comes with a comfortable handle and is dishwasher safe, making cleanup a breeze.

Another impressive feature of this stand mixer is its 10-speed screw control. This allows users to easily adjust the mixing speed for various tasks, from slow stirring to fast whipping. The precision of the speed settings ensures that users can achieve the perfect consistency for every recipe.

KitchenAid has also designed the 2316565B with a tilt-head mechanism. This thoughtful design allows for easy access to the mixing bowl and makes it simple to add ingredients while the mixer is in operation. The mixer comes with a range of accessories, including a flat beater, a dough hook, and a wire whip, catering to different mixing needs and recipes.

In addition to its functionality, the KitchenAid 2316565B is available in a variety of colors, allowing users to choose one that fits their kitchen aesthetic. The mixer's classic design and robust performance make it not only a practical kitchen tool but also a stylish addition to any countertop.

Overall, the KitchenAid 2316565B stand mixer is a reliable, efficient, and aesthetically pleasing appliance that provides an enjoyable cooking experience. Whether you're a beginner in the kitchen or a seasoned chef, this stand mixer is designed to meet all your mixing, kneading, and whipping needs, making it a valuable addition to any home.
Top Page Image Contents