Frymaster KSCF18G manual Gas Connections, Countries Supply Pressures Appliance Gas mbar Categories

Page 17

KSCF18G COOL ZONE SERIES GAS FRYERS

CHAPTER 3: INSTALLATION INSTRUCTIONS

3.3 Leveling the Fryer (cont.)

ANSI Z83.11/11a-(Latest Edition) requires a fryer be restrained to prevent tipping when installed in order to avoid the splashing of hot liquid. The means of restraint may be the manner of installation, such as connection to battery of appliances or installing the fryer in an alcove, or by separate means, such as adequate ties (chains, straps, etc.). A bracket has been provided on the fryer back panel for this purpose.

NOTE: The installation must be inspected after it is complete to ensure it meets the intent of these instructions. The on-site supervisor and/or operator(s) should be informed that the appliance is installed with restraints. If restraints are removed to move fryer (e.g., to clean beneath and behind, to relocate) ensure that they are re-installed when fryer is returned to its permanently installed position.

For information on fryer restraints, see Section 2.9.

3.4 Gas Connections

KSCF18G Cool Zone Series gas fryers have obtained CE markings for countries and gas categories shown below:

Countries

Supply Pressures

Appliance

Countries

Supply Pressures

Appliance

 

 

and Gas (mbar)

Categories

 

 

and Gas (mbar)

Categories

BE

Belgium

G20

20/25

I2E (R) B

GR

Greece

G20

20

II2H3P

G31

37

I3P

G31

37 and 50

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DE

Germany

G20

20

I2E

IR

Ireland

G20

20

II2H3P

G31

50

I3P

G31

37

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DK

Denmark

G20

20

I2H

IT

Italy

G20

20

I2H

 

 

 

 

 

 

 

 

 

 

ES

Spain

G20

20

II2H3P

LU

Luxembourg

G20/G25

20/25

II2E3P

 

 

G31

37 and 50

 

 

 

G31

50

 

FR

France

G20/G25

20/25

II2ESI3P

NL

The

G25

25

II2L3P

 

 

 

 

 

 

G31

37 and 50

 

 

Netherlands

G31

50

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GB

Great Britain

G20

20

II2H3P

PT

Portugal

G20

20

II2H3P

 

 

G31

37

 

 

 

G31

37

 

The gas supply (service) line must be the same size or greater than the fryer inlet line. KSCF18G gas fryers are equipped with a ¾-inch (22-mm) male inlet. The gas supply line must be sized to accommodate all gas-fired equipment connected to that gas supply. Consult local gas companies/suppliers or your local contractor for minimum supply line requirements.

3-4

Image 17
Contents Gas Fryers KSCF18G Cool Zone Page Page KSCF18G Cool Zone Gas Fryers Ordering Parts Applicability and ValidityAfter Purchase Computer Information Service InformationSafety Information Safety Information Service Personnel If your equipment arrives damaged Receiving and Unpacking EquipmentGeneral Rating Plate Pre-InstallationPrinciples of Operation ANSI/NFPA #70 Australian installations must meetAir Supply and Ventilation Equipment Installed at High AltitudesConversion of Units TemperatureRestraining the Fryer PressureRestraining the Fryer General Installing the FryerLeg and Caster Installation Leveling the Fryer InstallationRigid Casters Only Installing Optional Swivel CastersLegs Only Countries Supply Pressures Appliance Gas mbar Categories Gas ConnectionsSupply Line Specifications Regulating Gas Pressure Rigid ConnectionsManual Shut-off Valve Flexible Couplings, Connectors and Casters Gas Inputs Adjustments/Adaptation To Different GasesAdjustments for different gases are as follows Gas Conversion ProceduresNon-CE Gas Valve Fryer with KFC-1 Computer Safety SwitchesElectrical Connections Microswitch is located on the red handle at the drain valve Drain valve handle red Oil return handle Yellow label Final Preparation Initial Cleaning Before StartupDrop General Use Start-Up ProceduresPilot lighting procedures Standing Pilot Filtering Pilot lighting procedure Electronic IgnitionClosing See for detailed filtration proceduresFilter Powder Filter Paper Filter PreparationFilter Preparation Filter Preparation Filter Preparation Filter Operations Removing support grid from frypot prior to draining Yellow Label Filter Operations Weekly DailyBuilt-in Filtration Periodic/AnnualStainless Steel Periodic/ AnnualIntroduction KSCF18G Cool Zone Series GAS Fryers TroubleshootingPressed Fryer TroubleshootingCont Remains after closing drain Main burner malfunctions Pump wont Start Filtration System TroubleshootingWiring Diagrams Normally Open Float Switch Left 3 CE, Normally Open Float Switch Right 4 CE, Normally Open Float Switch Left Fast Ready 218G KSCF218GP00001 Fast Ready 218G KSCF218GP00001, KSCF218GN00007 Thermatron, 230V CE Constant Pilot, Fast Ready 218G Constant Pilot with KFC-1, 218G Oil Return, 218G/318G with Vent Solenoids 11 CE, Single Oil Return, Single KSCF18G Cool Zone Series GAS Fryers Troubleshooting Cabinetry and Related Components Component Accessories Component Box, Computers, and Related Components See Page 8-10 for High-Limit Thermostats Holder, Buss Fuse Drain Valve, Oil Return, and Related Components Component Drain System Filter Pan and Related Components Other Components Filter Pan AssemblyFrypot and Related Components Gas Valves, Pilot Assemblies, and Related Components Piezo Ignitor Components Trailing Pilot AssemblyRear Gas Manifold Components Over-the-Top Oil Return and Related Components 106-2983 Oil Return Assembly Cabinetry and Related Components Heat Shield, Flue Accessories Component Box, Computers, and Related Components See Page 9-10 for High-Limit Thermostats Holder, Buss Fuse Oil Return Handle Assembly 106-2215 Oil Suction Components 106-2214 Oil Return Assembly106-0979 Oil Return Bracket Assembly Filter Pan and Related Components Filter Components non-CE Export Filter Components823-4884SP CE Gas Valves Component Over-the-Top Oil Return and Related Components 106-3347 Oil Return Assembly Service Hotline