Frymaster KSCF18G manual Legs Only, Rigid Casters Only, Installing Optional Swivel Casters

Page 16

KSCF18G COOL ZONE SERIES GAS FRYERS

CHAPTER 3: INSTALLATION INSTRUCTIONS

3.3 Leveling the Fryer (cont.)

•Legs (Only)

1.Adjust leg height with an adjustable or 11/16-inch (27-mm) open-end wrench by turning the hex bullet on the bottom of the leg.

2.The hex bullet is for minor leg height adjustment only. Do not adjust more than 1 inch (25 mm).

3.When leveling the unit, the leg body should be held firmly to keep the leg from bending or rotating while turning the hex bullet foot to the required height.

•Rigid Casters (Only)

1.Install rigid casters on the fryer rear channel only. Legs must be installed on the front channel.

2.There are no level-adjustments for the rigid casters.

B.If the floor is uneven or has a decided slope, place the fryer on a smooth platform.

C.If the fryer is moved, re-level the fryer following the instructions given in Steps 3.3, A-C.

D.Installing Optional Swivel Casters

1.Install non-locking casters only at the rear of the unit.

2.Locking casters must be installed at the front of the unit. Locking casters allow the fryer to be "locked" in position for safe operations.

3.Follow the same instructions for leg installations as given above in Steps 3.2, B1-B5.

Front View

Rear Side View

Optional Caster-	Optional Caster-
Rear Only	Front Only

Front Channel or Rear Channel

Front or Rear Leg with

Mounting Plate

Adjust as needed

1/4-20 x 3/4 Hex Bolt

Front Channel or Rear Channel

Leg Support Assembly Washer

1/4-20 Hex Head Locknut

1/4-20 x 3/4 Hex Bolt

Rear Caster—5" Rigid	Front Caster—5" Swivel
	w/Brake

Leg and Caster (Optional) Mounting Installation

3-3

Image 16

Contents Gas Fryers KSCF18G Cool Zone Page Page KSCF18G Cool Zone Gas Fryers After Purchase Applicability and ValidityOrdering Parts Safety Information Service InformationComputer Information Safety Information Service Personnel General Receiving and Unpacking EquipmentIf your equipment arrives damaged Principles of Operation Pre-InstallationRating Plate Australian installations must meet ANSI/NFPA #70Equipment Installed at High Altitudes Air Supply and VentilationTemperature Conversion of UnitsRestraining the Fryer PressureRestraining the Fryer Leg and Caster Installation Installing the FryerGeneral Installation Leveling the FryerLegs Only Installing Optional Swivel CastersRigid Casters Only Gas Connections Countries Supply Pressures Appliance Gas mbar CategoriesSupply Line Specifications Manual Shut-off Valve Rigid ConnectionsRegulating Gas Pressure Flexible Couplings, Connectors and Casters Adjustments/Adaptation To Different Gases Gas InputsGas Conversion Procedures Adjustments for different gases are as followsNon-CE Gas Valve Electrical Connections Safety SwitchesFryer with KFC-1 Computer Microswitch is located on the red handle at the drain valve Drain valve handle red Oil return handle Yellow label Initial Cleaning Before Startup Final PreparationDrop Pilot lighting procedures Standing Pilot Start-Up ProceduresGeneral Use Pilot lighting procedure Electronic Ignition FilteringSee for detailed filtration procedures ClosingFilter Preparation Filter Powder Filter PaperFilter Preparation Filter Preparation Filter Preparation Filter Operations Removing support grid from frypot prior to draining Yellow Label Filter Operations Daily WeeklyPeriodic/Annual Built-in FiltrationPeriodic/ Annual Stainless SteelKSCF18G Cool Zone Series GAS Fryers Troubleshooting IntroductionFryer Troubleshooting PressedCont Remains after closing drain Main burner malfunctions Filtration System Troubleshooting Pump wont StartWiring Diagrams Normally Open Float Switch Left 3 CE, Normally Open Float Switch Right 4 CE, Normally Open Float Switch Left Fast Ready 218G KSCF218GP00001 Fast Ready 218G KSCF218GP00001, KSCF218GN00007 Thermatron, 230V CE Constant Pilot, Fast Ready 218G Constant Pilot with KFC-1, 218G Oil Return, 218G/318G with Vent Solenoids 11 CE, Single Oil Return, Single KSCF18G Cool Zone Series GAS Fryers Troubleshooting Cabinetry and Related Components Component Accessories Component Box, Computers, and Related Components See Page 8-10 for High-Limit Thermostats Holder, Buss Fuse Drain Valve, Oil Return, and Related Components Component Drain System Filter Pan and Related Components Filter Pan Assembly Other ComponentsFrypot and Related Components Gas Valves, Pilot Assemblies, and Related Components Rear Gas Manifold Components Trailing Pilot AssemblyPiezo Ignitor Components Over-the-Top Oil Return and Related Components 106-2983 Oil Return Assembly Cabinetry and Related Components Heat Shield, Flue Accessories Component Box, Computers, and Related Components See Page 9-10 for High-Limit Thermostats Holder, Buss Fuse Oil Return Handle Assembly 106-0979 Oil Return Bracket Assembly 106-2214 Oil Return Assembly106-2215 Oil Suction Components Filter Pan and Related Components Filter Components Filter Components non-CE Export823-4884SP CE Gas Valves Component Over-the-Top Oil Return and Related Components 106-3347 Oil Return Assembly Service Hotline