Frymaster KSCF18G manual Removing support grid from frypot prior to draining

Page 37

KSCF18G COOL ZONE SERIES GAS FRYERS

CHAPTER 5: FILTRATION

5.3 Filter Operations (cont.)

2.Remove the support grid from the frypot using the clean-out rod. Stir the oil with the L-shaped Teflon brush to suspend debris prior to draining.

Removing support grid from frypot prior to draining.

3.Open the fryer drain valve by pushing the red handle (under the frypot to be filtered) to the right until it is completely open. Continue stirring the oil.

Push the red handle right to open drain valve. Oil will start to drain into filter pan.

5-6

Image 37

Contents Gas Fryers KSCF18G Cool Zone Page Page KSCF18G Cool Zone Gas Fryers After Purchase Applicability and ValidityOrdering Parts Safety Information Service InformationComputer Information Safety Information Service Personnel General Receiving and Unpacking EquipmentIf your equipment arrives damaged Principles of Operation Pre-InstallationRating Plate ANSI/NFPA #70 Australian installations must meetAir Supply and Ventilation Equipment Installed at High AltitudesConversion of Units TemperatureRestraining the Fryer PressureRestraining the Fryer Leg and Caster Installation Installing the FryerGeneral Leveling the Fryer InstallationLegs Only Installing Optional Swivel CastersRigid Casters Only Countries Supply Pressures Appliance Gas mbar Categories Gas ConnectionsSupply Line Specifications Manual Shut-off Valve Rigid ConnectionsRegulating Gas Pressure Flexible Couplings, Connectors and Casters Gas Inputs Adjustments/Adaptation To Different GasesAdjustments for different gases are as follows Gas Conversion ProceduresNon-CE Gas Valve Electrical Connections Safety SwitchesFryer with KFC-1 Computer Microswitch is located on the red handle at the drain valve Drain valve handle red Oil return handle Yellow label Final Preparation Initial Cleaning Before StartupDrop Pilot lighting procedures Standing Pilot Start-Up ProceduresGeneral Use Filtering Pilot lighting procedure Electronic IgnitionClosing See for detailed filtration proceduresFilter Powder Filter Paper Filter PreparationFilter Preparation Filter Preparation Filter Preparation Filter Operations Removing support grid from frypot prior to draining Yellow Label Filter Operations Weekly DailyBuilt-in Filtration Periodic/AnnualStainless Steel Periodic/ AnnualIntroduction KSCF18G Cool Zone Series GAS Fryers TroubleshootingPressed Fryer TroubleshootingCont Remains after closing drain Main burner malfunctions Pump wont Start Filtration System TroubleshootingWiring Diagrams Normally Open Float Switch Left 3 CE, Normally Open Float Switch Right 4 CE, Normally Open Float Switch Left Fast Ready 218G KSCF218GP00001 Fast Ready 218G KSCF218GP00001, KSCF218GN00007 Thermatron, 230V CE Constant Pilot, Fast Ready 218G Constant Pilot with KFC-1, 218G Oil Return, 218G/318G with Vent Solenoids 11 CE, Single Oil Return, Single KSCF18G Cool Zone Series GAS Fryers Troubleshooting Cabinetry and Related Components Component Accessories Component Box, Computers, and Related Components See Page 8-10 for High-Limit Thermostats Holder, Buss Fuse Drain Valve, Oil Return, and Related Components Component Drain System Filter Pan and Related Components Other Components Filter Pan AssemblyFrypot and Related Components Gas Valves, Pilot Assemblies, and Related Components Rear Gas Manifold Components Trailing Pilot AssemblyPiezo Ignitor Components Over-the-Top Oil Return and Related Components 106-2983 Oil Return Assembly Cabinetry and Related Components Heat Shield, Flue Accessories Component Box, Computers, and Related Components See Page 9-10 for High-Limit Thermostats Holder, Buss Fuse Oil Return Handle Assembly 106-0979 Oil Return Bracket Assembly 106-2214 Oil Return Assembly106-2215 Oil Suction Components Filter Pan and Related Components Filter Components non-CE Export Filter Components823-4884SP CE Gas Valves Component Over-the-Top Oil Return and Related Components 106-3347 Oil Return Assembly Service Hotline