Frymaster KSCF18G manual Adjustments/Adaptation To Different Gases, Gas Inputs

Page 21

KSCF18G COOL ZONE SERIES GAS FRYERS

CHAPTER 3: INSTALLATION INSTRUCTIONS

3.4Gas Connections (cont.)

4.If it is necessary to disconnect the restraint, it must be reconnected after the fryer has been returned to its originally installed position.

WARNING

Do not attach accessories to this fryer unless fryer is secured from tipping.

Personal injury may result.

F.After hook-up, bleed the gas line of air to ensure that the pilot light will ignite quickly and evenly.

WARNING

Qualified personnel MUST perform any adaptation, modification, or gas conversion,

if required. Failure to use qualified personnel will void the Frymaster warranty.

3.5Adjustments/Adaptation To Different Gases

A.Proper operation of appliances requires the operator to scrupulously inspect the following:

1.Gas inputs and pressures;

2.Voltage and polarities of electrical power supplies.

B.Frymaster gas fryers are manufactured to use the type of gas and pressure specified on the rating plate. When changing gas, adaptation must be performed by qualified personnel. Failure to use qualified personnel will void the Frymaster warranty.

3.6Gas Inputs

A.Nominal "Qn" Heat Input for the KSCF18G Cool Zone Gas fryer is 25 kW.

B.Inputs for different gases are as follows:

	G20	Natural Gas	20 mbar/ 8" W.C.
	G20	(Type H)	20 mbar/ 8" W.C.
		(Type H)

	G25	Natural Gas	25 mbar/ 10" W.C.
	G25	(Type L)	25 mbar/ 10" W.C.
		(Type L)

	G31	Propane	37 mbar/ 15" W.C.

3-8

Image 21

Contents Gas Fryers KSCF18G Cool Zone Page Page KSCF18G Cool Zone Gas Fryers Applicability and Validity After PurchaseOrdering Parts Service Information Safety InformationComputer Information Safety Information Service Personnel Receiving and Unpacking Equipment GeneralIf your equipment arrives damaged Pre-Installation Principles of OperationRating Plate ANSI/NFPA #70 Australian installations must meetAir Supply and Ventilation Equipment Installed at High AltitudesConversion of Units TemperatureRestraining the Fryer PressureRestraining the Fryer Installing the Fryer Leg and Caster InstallationGeneral Leveling the Fryer InstallationInstalling Optional Swivel Casters Legs OnlyRigid Casters Only Countries Supply Pressures Appliance Gas mbar Categories Gas ConnectionsSupply Line Specifications Rigid Connections Manual Shut-off ValveRegulating Gas Pressure Flexible Couplings, Connectors and Casters Gas Inputs Adjustments/Adaptation To Different GasesAdjustments for different gases are as follows Gas Conversion ProceduresNon-CE Gas Valve Safety Switches Electrical ConnectionsFryer with KFC-1 Computer Microswitch is located on the red handle at the drain valve Drain valve handle red Oil return handle Yellow label Final Preparation Initial Cleaning Before StartupDrop Start-Up Procedures Pilot lighting procedures Standing PilotGeneral Use Filtering Pilot lighting procedure Electronic IgnitionClosing See for detailed filtration proceduresFilter Powder Filter Paper Filter PreparationFilter Preparation Filter Preparation Filter Preparation Filter Operations Removing support grid from frypot prior to draining Yellow Label Filter Operations Weekly DailyBuilt-in Filtration Periodic/AnnualStainless Steel Periodic/ AnnualIntroduction KSCF18G Cool Zone Series GAS Fryers TroubleshootingPressed Fryer TroubleshootingCont Remains after closing drain Main burner malfunctions Pump wont Start Filtration System TroubleshootingWiring Diagrams Normally Open Float Switch Left 3 CE, Normally Open Float Switch Right 4 CE, Normally Open Float Switch Left Fast Ready 218G KSCF218GP00001 Fast Ready 218G KSCF218GP00001, KSCF218GN00007 Thermatron, 230V CE Constant Pilot, Fast Ready 218G Constant Pilot with KFC-1, 218G Oil Return, 218G/318G with Vent Solenoids 11 CE, Single Oil Return, Single KSCF18G Cool Zone Series GAS Fryers Troubleshooting Cabinetry and Related Components Component Accessories Component Box, Computers, and Related Components See Page 8-10 for High-Limit Thermostats Holder, Buss Fuse Drain Valve, Oil Return, and Related Components Component Drain System Filter Pan and Related Components Other Components Filter Pan AssemblyFrypot and Related Components Gas Valves, Pilot Assemblies, and Related Components Trailing Pilot Assembly Rear Gas Manifold ComponentsPiezo Ignitor Components Over-the-Top Oil Return and Related Components 106-2983 Oil Return Assembly Cabinetry and Related Components Heat Shield, Flue Accessories Component Box, Computers, and Related Components See Page 9-10 for High-Limit Thermostats Holder, Buss Fuse Oil Return Handle Assembly 106-2214 Oil Return Assembly 106-0979 Oil Return Bracket Assembly106-2215 Oil Suction Components Filter Pan and Related Components Filter Components non-CE Export Filter Components823-4884SP CE Gas Valves Component Over-the-Top Oil Return and Related Components 106-3347 Oil Return Assembly Service Hotline