Frymaster KSCF18G manual ANSI/NFPA #70, Australian installations must meet

Page 10

KSCF18G COOL ZONE SERIES GAS FRYERS

CHAPTER 2: IMPORTANT INFORMATION

2.5 Pre-Installation (cont.)

DANGER

This appliance must be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of substances harmful to the health of personnel in the room in which it is installed.

B.Clearances: The fryer area must be free of all combustibles. This unit is design-certified for the following installations:

1.Commercial installation only; not for household use.

2.Non-combustible floor installation equipped with factory-supplied 6-inch (15-cm) adjustable legs or 5-inch (13-cm) casters;

3.Combustible construction with a minimum clearance of 6-inches (15-cm) side and 6-inches (15-cm) rear, and equipped with factory-supplied 6-inch (15-cm) adjustable legs or 5-inch

(13-cm) casters.

C.Installation Standards

1. U.S. installations must meet:

2. Canadian installations must meet:

American National Standard Institute

CAN 1-B149 Installation Codes

ANSI Z83.11

Canadian Gas Association

American Gas Association

55 Scarsdale Road

8501 E. Pleasant Valley Road

Don Mills, ONT, M3B 2R3

Cleveland, OH 44131

 

National Electrical Code

Canadian Electric Code c22.1, part 1

ANSI/NFPA #70

Canadian Standards Association

American National Standard Institute

178 Rexdale Blvd.

1430 Broadway

Rexdale, ONT, M9W 1R3

New York, NY 10018

 

NFPA Standards #96 and #211

3. Australian installations must meet:

National Fire Protection Association

 

470 Atlantic Avenue

AS5601/AG601 Installation Codes

Boston, MA 02110

Standards Australia International

 

25 Raglan Street

 

South Melbourne, VIC 3205

4.CE/EXPORT STANDARDS: Fryer installation must conform with local codes, or in the absence of local codes, to the appropriate national or European Community (CE) standards.

2-3

Image 10
Contents Gas Fryers KSCF18G Cool Zone Page Page KSCF18G Cool Zone Gas Fryers After Purchase Applicability and ValidityOrdering Parts Safety Information Service InformationComputer Information Safety Information Service Personnel General Receiving and Unpacking EquipmentIf your equipment arrives damaged Principles of Operation Pre-InstallationRating Plate Australian installations must meet ANSI/NFPA #70Equipment Installed at High Altitudes Air Supply and VentilationRestraining the Fryer TemperatureConversion of Units PressureRestraining the Fryer Leg and Caster Installation Installing the FryerGeneral Installation Leveling the FryerLegs Only Installing Optional Swivel CastersRigid Casters Only Gas Connections Countries Supply Pressures Appliance Gas mbar CategoriesSupply Line Specifications Manual Shut-off Valve Rigid ConnectionsRegulating Gas Pressure Flexible Couplings, Connectors and Casters Adjustments/Adaptation To Different Gases Gas InputsGas Conversion Procedures Adjustments for different gases are as followsNon-CE Gas Valve Electrical Connections Safety SwitchesFryer with KFC-1 Computer Microswitch is located on the red handle at the drain valve Drain valve handle red Oil return handle Yellow label Initial Cleaning Before Startup Final PreparationDrop Pilot lighting procedures Standing Pilot Start-Up ProceduresGeneral Use Pilot lighting procedure Electronic Ignition FilteringSee for detailed filtration procedures ClosingFilter Preparation Filter Powder Filter PaperFilter Preparation Filter Preparation Filter Preparation Filter Operations Removing support grid from frypot prior to draining Yellow Label Filter Operations Daily WeeklyPeriodic/Annual Built-in FiltrationPeriodic/ Annual Stainless SteelKSCF18G Cool Zone Series GAS Fryers Troubleshooting IntroductionFryer Troubleshooting PressedCont Remains after closing drain Main burner malfunctions Filtration System Troubleshooting Pump wont StartWiring Diagrams Normally Open Float Switch Left 3 CE, Normally Open Float Switch Right 4 CE, Normally Open Float Switch Left Fast Ready 218G KSCF218GP00001 Fast Ready 218G KSCF218GP00001, KSCF218GN00007 Thermatron, 230V CE Constant Pilot, Fast Ready 218G Constant Pilot with KFC-1, 218G Oil Return, 218G/318G with Vent Solenoids 11 CE, Single Oil Return, Single KSCF18G Cool Zone Series GAS Fryers Troubleshooting Cabinetry and Related Components Component Accessories Component Box, Computers, and Related Components See Page 8-10 for High-Limit Thermostats Holder, Buss Fuse Drain Valve, Oil Return, and Related Components Component Drain System Filter Pan and Related Components Filter Pan Assembly Other ComponentsFrypot and Related Components Gas Valves, Pilot Assemblies, and Related Components Rear Gas Manifold Components Trailing Pilot AssemblyPiezo Ignitor Components Over-the-Top Oil Return and Related Components 106-2983 Oil Return Assembly Cabinetry and Related Components Heat Shield, Flue Accessories Component Box, Computers, and Related Components See Page 9-10 for High-Limit Thermostats Holder, Buss Fuse Oil Return Handle Assembly 106-0979 Oil Return Bracket Assembly 106-2214 Oil Return Assembly106-2215 Oil Suction Components Filter Pan and Related Components Filter Components Filter Components non-CE Export823-4884SP CE Gas Valves Component Over-the-Top Oil Return and Related Components 106-3347 Oil Return Assembly Service Hotline