Frymaster 8196203 manual Navy Surface Ship Electric Fryers Filtration Instructions, Introduction

Page 17

NAVY SURFACE SHIP ELECTRIC FRYERS

CHAPTER 4: FILTRATION INSTRUCTIONS

4.1Introduction

The FootPrint Pro filtration system allows the cooking oil or shortening in one frypot to be safely and efficiently filtered while the other frypots in a battery remain in operation. Section 4.2 covers preparation of the filter system for use. Operation of the system is covered in section 4.3.

WARNING

The work center supervisor is responsible for ensuring that operators are made aware of the inherent hazards of operating a hot oil filtering system, particularly the aspects of oil filtration, draining and cleaning procedures.

4.2Preparing the Filter for Use

1.Rotate the pan-locking rod to either side until it clears the filter pan, then pull the pan out from the cabinet. Remove the crumb tray, hold-down ring and filter screen. Clean all components with a solution of detergent and hot water then dry thoroughly.

The filter pan is equipped with rollers in rails, much like a kitchen drawer. The pan may be removed for cleaning or to gain access to interior components by lifting the front of the pan to disengage the front rollers, then pulling it forward until the rear rollers clear the rails. The pan cover must not be removed except for cleaning, interior access, or to allow a shortening disposal unit (SDU) to be positioned under the drain.

Rotate the locking rod to either side to allow the pan to be pulled out from the fryer.

2.Inspect the filter pan connection fitting to ensure that both O-rings are in good condition. O-rings are located on the tube disconnect inside the filter pan as shown to the right.

Inspect O-Rings

4-1

Image 17
Contents Navy Surface Ship Electric Fryers Hour Service Hotline NOVPage Canada Navy Surface Ship Electric Fryers General Safety InformationNavy Surface Ship Electric Fryers Introduction Controller Information Shipping Damage Claim ProcedureService Information Introduction Navy Surface Ship Electric Fryers Installation InstructionsPage Power Requirements Single Fryer with Filter Dimensions and WeightsSingle Fryer non-filter Fryer Battery62.55 Navy Surface Ship Electric Fryers Operating Instructions Equipment Setup and Shutdown ProceduresOperation of the Solid-State Analog Controller ShutdownController Operating Procedure Page Navy Surface Ship Electric Fryers Filtration Instructions Open drain valve by rotating 90º Filter Pump Reset Switch Page Navy Surface Ship Electric Fryers Preventive Maintenance Page Check Calibration of Temperature Control Knob Monthly Clean Detachable Parts and Accessories WeeklyBuilt-In Filtration System Annual/Periodic System InspectionFryer Page Navy Surface Ship Electric Fryers Operator Troubleshooting Troubleshooting Control and Heating Problems Problem Probable Causes Corrective ActionProblem Filtration Problems Error Messages and Display ProblemsProblem Probable Causes Replacing Component Box Components Navy Surface Ship Electric Fryers Service ProceduresReplacing a Controller Replacing a High-Limit Thermostat Replacing a Temperature Probe Replacing a Heating Element Position Replacing Contactor Box Components Replacing a Frypot Page Sediment Particle Oil Flow Up for reverse Down for forward Disconnect flexlines indicated by the arrows Page Replacing the Filter Transformer or Filter Relay Diagnostic LED Legend Interface Board Diagnostic ChartProbe Resistance Chart Probe Resistance ChartRefer to page 2-2 for power requirements Refer to page 2-2 for power requirements Refer to page 2-2 for power requirements Wiring Diagram, Wiring Harness Page Accessories Navy Surface Ship Electric Fryers Parts ListPage Two and Three Station Fryers Cabinets, Bases, Braces, and Associated Parts Cabinet Bases, Braces, and Associated Parts See next section for Drain PART# Drain Tube Section and Associated PartsNut, ½-13 2-Way Hex Lock PART# Page Item PART# Relays are not replaceable Electronics and Wiring Components Component Boxes807-3575 Not illustrated Contactor Boxes Contactor Boxes Heating Element Assembly and Associated Parts Heating Element Assembly and Associated Parts Contactor Box Wiring Assembly 12-Pin Full-Vat C-1 WiringContactor Box Wiring Assemblies 6-Pin Left Element Controller106-5750 106-5935 Interface Board to Controller Wiring Harness 15-Pin Filtration System Components 1 FPH17 Filtration Components Assembly, Filter Pan Single includes pan and lid Multiple Battery Filtration System Components Multiple Battery Filtration System Components Frypot Assembly and Thermostat Oil Return System Components Component Component Wiring Connectors, Pin Terminals and Power CordsFasteners This page Intentionally Left Blank Service Hotline

8196203 specifications

The Frymaster 8196203 is a highly regarded commercial fryer that has carved a niche in the fast-paced environment of restaurants and food service operations. This unit combines advanced technology with robust design, making it an ideal choice for those who demand efficiency and consistency in their frying processes.

One of the standout features of the Frymaster 8196203 is its high-capacity frying system. With the ability to handle large batches, this fryer is perfect for busy kitchens that require quick service without sacrificing food quality. The unit is engineered to provide optimal heating, ensuring that oil is quickly brought to the desired frying temperature, reducing wait times and improving overall productivity.

The Frymaster 8196203 is equipped with a powerful heating system that utilizes innovative technologies for enhanced performance. It often includes options for both gas and electric heating, catering to the specific needs of various kitchen environments. The unit's design promotes even heat distribution, reducing the risk of uneven cooking and guaranteeing that every piece of food is crisped to perfection.

Furthermore, the fryer features a sophisticated filtration system that helps maintain oil quality. This system automatically filters out food particles and other impurities, extending the life of the cooking oil and ensuring that the flavor of the food remains untainted. As a result, operators can save on oil costs while also ensuring food quality stays high.

Safety is another important aspect of the Frymaster 8196203, which includes built-in features such as temperature controls and safety shut-off mechanisms. These features help prevent overheating and accidents, allowing kitchen staff to focus on cooking rather than constantly monitoring the fryer.

The Frymaster 8196203 is designed with user-friendliness in mind. Its intuitive control panel allows for easy adjustments and monitoring, ensuring that cooks can operate it with minimal training. Additionally, the fryer is constructed with durable materials that are easy to clean, which is essential for maintaining hygiene in any food service environment.

In conclusion, the Frymaster 8196203 is a reliable commercial fryer that stands out for its high capacity, advanced heating technology, and efficiency-enhancing features. With a focus on safety, ease of use, and maintenance, it’s a valuable addition to any kitchen, helping chefs produce mouth-watering fried dishes with speed and consistency.