Frymaster 8196203 manual Error Messages and Display Problems, Filtration Problems

Page 29

6.2.2 Error Messages and Display Problems

Problem

Probable Causes

Corrective Action

 

 

This in an indication of a

 

 

malfunction in the temperature

Controller trouble

Oil temperature above acceptable

measuring or control circuitry,

including a failure of the high limit

range or a problem with the

light ON.

thermostat. Determining the

temperature measuring circuitry.

 

specific problem is beyond the

 

 

 

 

scope of operator troubleshooting.

 

 

Shut the fryer down immediately.

 

 

Verify that the drain valve is fully

Controller trouble

 

closed. The fryer will not function

Open drain valve or problem with

if the drain valve is not fully

light ON and heating

closed. If the drain valve is fully

latching circuits

mode light ON.

closed, the problem is within the

 

 

 

latching circuitry and is beyond the

 

 

scope of operator troubleshooting.

6.2.3 Filtration Problems

 

Problem

Probable Causes

Corrective Action

 

 

A. Verify that the power cord is

 

A. Power cord is not plugged in or

fully plugged in. If so, verify

 

circuit breaker is tripped.

that circuit breaker is not

 

 

tripped.

 

 

B. If the motor is too hot to touch

 

 

for more than a few seconds, the

 

B. Pump motor has overheated

thermal overload switch has

 

causing the thermal overload

probably tripped. Allow the

Filter pump won't

switch to trip.

motor to cool at least 20

 

minutes then press the Pump

start.

 

 

Reset Switch.

 

 

 

C. Blockage in filter pump.

C. Pump blockages are usually

 

Test: Close the drain valve and

caused by sediment buildup in

 

the pump due to improperly

 

pull the filter pan out from the

sized or installed filter paper

 

fryer. Activate the pump. If the

and failure to use the crumb

 

pump motor hums for a short time

screen.

 

then stops, the probable cause is

 

 

blockage of the pump itself.

 

(continued on following page)

6-4

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Navy Surface Ship Electric Fryers Hour Service Hotline NOVPage Canada Navy Surface Ship Electric Fryers General Safety InformationNavy Surface Ship Electric Fryers Introduction Controller Information Shipping Damage Claim ProcedureService Information Introduction Navy Surface Ship Electric Fryers Installation InstructionsPage Power Requirements Single Fryer with Filter Dimensions and WeightsSingle Fryer non-filter Fryer Battery62.55 Navy Surface Ship Electric Fryers Operating Instructions Equipment Setup and Shutdown ProceduresOperation of the Solid-State Analog Controller ShutdownController Operating Procedure Page Navy Surface Ship Electric Fryers Filtration Instructions Open drain valve by rotating 90º Filter Pump Reset Switch Page Navy Surface Ship Electric Fryers Preventive Maintenance Page Check Calibration of Temperature Control Knob Monthly Clean Detachable Parts and Accessories WeeklyBuilt-In Filtration System Annual/Periodic System InspectionFryer Page Navy Surface Ship Electric Fryers Operator Troubleshooting Troubleshooting Control and Heating Problems Problem Probable Causes Corrective ActionProblem Filtration Problems Error Messages and Display ProblemsProblem Probable Causes Replacing Component Box Components Navy Surface Ship Electric Fryers Service ProceduresReplacing a Controller Replacing a High-Limit Thermostat Replacing a Temperature Probe Replacing a Heating Element Position Replacing Contactor Box Components Replacing a Frypot Page Sediment Particle Oil Flow Up for reverse Down for forward Disconnect flexlines indicated by the arrows Page Replacing the Filter Transformer or Filter Relay Diagnostic LED Legend Interface Board Diagnostic ChartProbe Resistance Chart Probe Resistance ChartRefer to page 2-2 for power requirements Refer to page 2-2 for power requirements Refer to page 2-2 for power requirements Wiring Diagram, Wiring Harness Page Accessories Navy Surface Ship Electric Fryers Parts ListPage Two and Three Station Fryers Cabinets, Bases, Braces, and Associated Parts Cabinet Bases, Braces, and Associated Parts See next section for Drain PART# Drain Tube Section and Associated PartsNut, ½-13 2-Way Hex Lock PART# Page Item PART# Relays are not replaceable Electronics and Wiring Components Component Boxes807-3575 Not illustrated Contactor Boxes Contactor Boxes Heating Element Assembly and Associated Parts Heating Element Assembly and Associated Parts Contactor Box Wiring Assembly 12-Pin Full-Vat C-1 WiringContactor Box Wiring Assemblies 6-Pin Left Element Controller106-5750 106-5935 Interface Board to Controller Wiring Harness 15-Pin Filtration System Components 1 FPH17 Filtration Components Assembly, Filter Pan Single includes pan and lid Multiple Battery Filtration System Components Multiple Battery Filtration System Components Frypot Assembly and Thermostat Oil Return System Components Component Component Wiring Connectors, Pin Terminals and Power CordsFasteners This page Intentionally Left Blank Service Hotline

8196203 specifications

The Frymaster 8196203 is a highly regarded commercial fryer that has carved a niche in the fast-paced environment of restaurants and food service operations. This unit combines advanced technology with robust design, making it an ideal choice for those who demand efficiency and consistency in their frying processes.

One of the standout features of the Frymaster 8196203 is its high-capacity frying system. With the ability to handle large batches, this fryer is perfect for busy kitchens that require quick service without sacrificing food quality. The unit is engineered to provide optimal heating, ensuring that oil is quickly brought to the desired frying temperature, reducing wait times and improving overall productivity.

The Frymaster 8196203 is equipped with a powerful heating system that utilizes innovative technologies for enhanced performance. It often includes options for both gas and electric heating, catering to the specific needs of various kitchen environments. The unit's design promotes even heat distribution, reducing the risk of uneven cooking and guaranteeing that every piece of food is crisped to perfection.

Furthermore, the fryer features a sophisticated filtration system that helps maintain oil quality. This system automatically filters out food particles and other impurities, extending the life of the cooking oil and ensuring that the flavor of the food remains untainted. As a result, operators can save on oil costs while also ensuring food quality stays high.

Safety is another important aspect of the Frymaster 8196203, which includes built-in features such as temperature controls and safety shut-off mechanisms. These features help prevent overheating and accidents, allowing kitchen staff to focus on cooking rather than constantly monitoring the fryer.

The Frymaster 8196203 is designed with user-friendliness in mind. Its intuitive control panel allows for easy adjustments and monitoring, ensuring that cooks can operate it with minimal training. Additionally, the fryer is constructed with durable materials that are easy to clean, which is essential for maintaining hygiene in any food service environment.

In conclusion, the Frymaster 8196203 is a reliable commercial fryer that stands out for its high capacity, advanced heating technology, and efficiency-enhancing features. With a focus on safety, ease of use, and maintenance, it’s a valuable addition to any kitchen, helping chefs produce mouth-watering fried dishes with speed and consistency.
Top Page Image Contents