Ice-O-Matic GEM0956R, GEM1256R, GEM0650R Bin Application, Ice Machine Specifications

Page 10

GEM0650/0956/1256 Remote

For the Installer

Bin Application

The Pearl Ice™ Series are designed to fit the following Ice-O-Matic Bins ●B42, using Bin Top KBT 24 (Note: GEM0650 and GEM0956 ONLY) ●B25, B40 B55 using Bin Top KBT 19.

●B100 using Bin Top KBT 23 (one unit) or KBT 22 (two units). ●B120, B150, B170 Not designed for Pearl Ice™ Series.

Dispenser Application

The Pearl Ice™ Series can be placed on and used with certain ice and beverage dispensers. Kits are required for proper operation.

IOM Pearl Ice™ Accessory List

Dispenser	GEM0650	GEM0956
Ice-O-Matic IOD150	KBT15022, KGEMDIV	KBT15022, KGEMDIV

Ice-O-Matic IOD200 or	KBT25022, KGEMBIOD	KBT25022, KGEMBIOD
IOD250
Cornelius ED or DF150	KBT15022,	KBT15022,
	R629088514(Cornelius	R629088514(Cornelius
	Model)	Model)

Cornelius ED or DF200	KBT25022, KGEM200	KBT25022, KGEM200

Cornelius ED or DF250	KBT25022, KGEM250	KBT25022, KGEM250

Lancer Nugget Ready	N/A	N/A
Flavor Select
SerVend S-200, SV200, S-	N/A	N/A
250, SV-250

GEM1256

Does not fit

KBT25030, KGEMBIOD, KGEMDIV

Does not fit

KBT25030, KGEM200

KBT25030, KGEM250

N/A

N/A

Ice Machine Specifications

	Model	WxDxH	Basic			Minimum Circuit	Maximum	Refrigerant
	Number	(Inches)	Electrical		Condenser	Ampacity	Fuse Size	Charge oz. R404

GEM0650R		21x24x27	115/60/1		Remote	22.5	30	208
GEM0956R		21x24x27 208-230/60/1 Remote				14.1	20	208
GEM1256R		30x24x27	208-230/60/1		Remote	17.3	25	208

Page 4

Image 10

Contents Pearl Ice Series By Ice-O-MaticPage Introduction Keep this manual for future referenceTable Of Contents Visible Loss or Damage Freight Claim ProcedureInspect Promptly Concealed Loss or DamageWarranty Governing LAWFor the Installer GEM0650/0956R GEM1256R Ice Machine Specifications Bin ApplicationIce machine LocationStorage Bin Water LimitationsPearl Ice Number ERC Dimensions Inches GRC1001 GRC1061 GCR2061Remote Condenser Line SetsCalculation Formula Remote Condenser LocationCalculation Example Roof Attachment Remote Condenser LocationPrecharged Line Set Routing Typical Installation Coupling Instructions Initial Connections Final ConnectionsWater Inlet For the PlumberDrains Ice Machine For the Electrician Completed Installation Final Check List Pre-Start Inspection There are no adjustments to make, so replace the panelsStart Up Start UpComponent Description Control Board GEM0650/0956/1256 Remote Electrical Sequence Water Level Operation WaterWater Water SystemRefrigeration Schematic Operation RefrigerationLow Condensing Temperature Pump Down Operation Performance Sanitizing and Cleaning Condenser Maintenance Brush in direction of finsBearing Maintenance Bearing MaintenanceBin Control Sensor Sensor MaintenanceWater Sensor Auger Maintenance AugerService Diagnosis Symptom Possible Cause Probable CorrectionSymptom Control System Diagnostics High pressure cut out checkWater Reservoir Water Reservoir, Bin ControlBin Controls Ice Level Sensors To Remove the Breaker Bearing Assembly Bearing and BreakerAuger To Remove the AugerRemoval of the Water Seal To Replace the Water Seal Water SealTo Remove the Water Seal Replacing the Water SealTo Replace the Evaporator EvaporatorTo Reassemble the Evaporator and Auger To Check the Gear Motor To Remove and Repair the Gear Motor AssemblyGear Motor To Inspect the Gear MotorTo Remove the Condenser Fan Motor Assembly Fan Blade and MotorRefrigeration Service Charging ProcedureGEM0650R Wiring Diagram Wiring Diagram GEM0650RGEM0956R Wiring Diagram Wiring Diagram GEM0956RGEM1256R Wiring Diagram Wiring Diagram GEM1256RService History What to Do Before Calling for Service