Cleveland Range (T) MKDL-60-T (-CC), (T) MKDL-125-T (-CC) manual Moving Unit, Leveling

Page 4

Shim as

 

 

required

 

 

to make

 

 

level with

 

 

center

 

 

console

 

 

(front

 

Jack

and back)

 

 

4"x4" or larger

 

 

(front and back)

 

 

Skid

Flanged feet

Forklift tongs

Recommended Installation Procedure

MOVING UNIT

1.While still on skid, move unit as close to final installation position as possible.

2.Prepare unit for lifting as shown in diagram.

3.Lift gently with a forklift or jacks and remove skid.

4.Lower gently to ground and remove forklift and blocking.

5. If unit has to be re-positioned, slide gently. Do not twist or push one side of unit excessively and cause binding on trunnions.

LEVELING

Note: Instructions reflect a more complicated twin mixer kettle - process for single mixer kettles is the same.

 

 

 

 

 

 

 

 

 

B

3.

Level consoles individually from front to back

B

 

 

 

 

(dotted lines C). Adjustments are made by turning

 

 

 

A

 

 

 

 

 

flanges on front feet only.

A

 

 

 

 

 

 

 

 

 

4. Re-check that the back is level (dotted line B)

 

 

 

 

 

 

 

 

 

 

 

and then the front (dotted line D). Adjust if

 

 

 

 

 

 

necessary.

C

C

C

 

 

 

5. Check that mixer bridge is level and

 

 

 

C

C

 

guide pins lock smoothly without

 

 

 

 

binding. If not repeat steps 1 through 4.

 

C

 

 

 

 

 

 

 

 

D

 

 

 

D

Guide Pins

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE: See Operating Instructions before

 

 

 

 

 

operating unit.

 

 

 

 

 

6. Make electrical connections (see electrical

 

 

 

 

 

 

service connections) and test mixer bridge as

Recommended Leveling Procedure

 

 

 

follows:

1.With straight-edge, line the backs of the consoles up with each other (dotted line A).

2.Level and straight-edge backs of consoles (dotted line B). Adjustments are made by turning flanges on back feet only.

⇒A/ Raise mixer bridge.

⇒B/ Swing bridge out over centre console.

⇒C/ Swing bridge to the left as far as possible.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Operators Manual For your safety General InspectionShipping Damage Instructions Clearance RequirementsMoving Unit LevelingCompressed AIR Connection Electrical Service ConnectionsPiping Connections Steam Requirements for Kettles Piping SchematicSteam Pipe Sizing Quality Assurance Checklist Some units may not have the following items to test Operating Instructions Item no Description Function Operating Suggestions 2000 Mixer Kettle Operation Using CAL Mixer Kettle Operation Using MRC 7000 1 PEN Care and Cleaning Cleaning InstructionsScraper Blades Product ValveStainless Steel Equipment Care and Cleaning Service Parts WarrantyHydraulic Components Item noKE50294 Mercury Switch FA95055-3 Remote Control Assembly ClevelandDescription QTY Main Console Controls Item no Description Switch Configuration IndexSpeed Control Electrical Component Assembly Bracket for Thermostat Plumbing Assembly 10 Console Solenoid Valve, 1 1/4 100 psiPlumbing Assembly 18 Console Manual Tilt 10 Console Power Tilt 10/12 Console Power Tilt 10/12 Console Water Meter Assembly 18 Console Water Meter Assembly Console Flush Piston Flush Piston AIR SYSTEM, 10 Console Lubricator Used Prior to Item on Description QTY Used After to For MKDL-40CC Flush Piston AIR Solenoid Valve Butterfly Valve Main Component Reference Charts ValvesMaintenance AIR Line Lubricator OIL Filling Procedure AIR Filter Replacement ProcedureAutomatic Dump Valve Steam TrapRE-INSTALLING Speed Control Cable Hydraulic OIL Replacement ProcedureDisassembly of Switch Assembly LubricationSolenoid Valve Maintenance Ordering InformationCoil Replacement MRC 7000 Enable Mode Procedure 1&2 PEN For Cook Chill Direct Steam Mixer KettlesWiring Diagram Twin Kettles Flow Path for Hydraulic System Spare Parts List Spare Parts
Top Page Image Contents