Alto-Shaam 1220 manual Site Installation, Installation codes & Standards, Ventilation requirements

Page 5

i n s t a l l a t i o n

site INSTALLATION

d a n g e r

IMPROPER INSTALLATION,

ALTERATION, ADJUSTMENT, SERVICE, OR MAINTENANCE COULD RESULT IN SEVERE INJURY, DEATH, OR CAUSE PROPERTY DAMAGE.

READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.

d a n g e r

AVERTISSEMENT : UNE INSTALLATION, UN AJUSTEMENT, UNE ALTÉRATION, UN SERVICE OU UN ENTRETIEN NON CONFORME AUX NORMES PEUT CAUSER DES DOMMAGES À LA PROPRIÉTÉ, DES BLESSURES OU LA MORT.

LIRE ATTENTIVEMENT LES DIRECTIVES D’OPÉRATION ET D’ENTRETIEN AVANT DE FAIRE L’INSTALLATION, OU L’ENTRETIEN DE CET ÉQUIPEMENT.

c a u t i o n

TO PREVENT PERSONAL INJURY, USE CAUTION WHEN MOVING OR LEVELING THIS APPLIANCE.

danger

DO NOT store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.

SITE INSTALLATION

installation codes & Standards

The following codes and standards are required for installation of this oven: air supply, electrical connections, water connections, and waste water discharge.

NOTE:

Where automatically operated appliances are vented through a ventilating hood or exhaust system equipped with a damper or with a power means of exhaust, provisions shall be made to allow the equipment to operate only when the damper is open to a position to properly vent the appliance and when the power means of exhaust is in operation.

in accordance with NFPA 54 commonwealth of massachusetts only.

ventilation requirements

A steam ventilation hood is mandatory for the operation of the oven. The ventilation hood must be installed in accordance with local building codes for the steam exhaust and must protrude 12-inches to 20-inches (300 to 500mm) over the front side of the oven. A grease filter must be located in the protruding area of the hood. Grease filters should be thoroughly cleaned on a regular basis following manufacturer's instruction. Ventilation hoods must ensure an adequate amount of incoming air during operation and must be operated whenever the combination oven/steamer is used in order to avoid the accumulation of condensation in the hood area.

CombiTherm® ES series • electric INSTALLATION MANUAL #MN-28897 • 3.

Image 5
Contents ES electric Installation P a c k i n g L i v e r yN g e r Safety procedures and precautionsVentilation requirements Site InstallationInstallation codes & Standards Minimum Clearance Requirements Positioning on siteLifting Instructions Positioning requirements Combitherm Cleaning Liquid CE-24750 Accessories610ES 610es610ES Touch 610ESi 610esi610ESi Touch 610ESiN 610esiN610ESiN Touch 1010ES 1010es1010ES Touch 1010ESi 1010esi1010ESi Touch 35-7/8 910mm Water Drain 33-7/8 860mm Rear 1010esiN714ES 714es714ES Touch 714ESi 714esi714ESi Touch Water supply shut-off valve and back-flow preventer 1018es1018esi 1018esi/sk 1018esiBack 1151mm 1220es106mm 1220esi60-1/4 x 26-1/4 x 32-11/16 1530mm x 667mm x 830mm 2020es2020esi 2020esi/sk 2020esiElectrical connection Hard wired modelsTerminal Block Ground Electrical Connection Following Electrical Connection Risk of electric shock Mobile equipment restraintWater quality requirement Water requirements Two 2 cold water inlets drinking quality Water connectionsWater drainage Water ValveClearances E c k l i s tFaulty or plugged solenoid valve assembly Faulty or scaled water level probeWiring or connection issue Incorrect power to the unitConnection issue with B-4 probe Problem with water level probeFaulty B-4 probe Connection issue at B-3 probeFaulty drain pump Temperature sensor shorted to ground/faultyPlugged or faulty Y-1 solenoid Connection issue at X-3 personality jumperBypass Probe Fault Oven Probe FaultTo 284F Excess Oven TempCondensate drain Ventless hood optionOperation Ventless Hood Power KnobOriginal equipment limited warranty TRansportation damage and claims
Related manuals
Manual 41 pages 12.09 Kb

1220 specifications

Alto-Shaam is known for its innovative cooking and holding equipment designed for the foodservice industry, and their VHes product line is no exception. This range includes models VHes-10, VHes-5, 1220, 610, and 714, each built with unique features and advanced technologies to meet the demands of modern kitchens.

The VHes-10 and VHes-5 models are equipped with Alto-Shaam’s exclusive Halo Heat technology, which provides precise temperature control and ensures even heat distribution. This technology gently holds food at the perfect serving temperature without drying it out, enhancing both flavor and texture. These models also feature Energy Star certification, reflecting their energy-efficient design, which helps kitchens reduce operational costs while supporting sustainability goals.

The VHes-10 boasts a larger capacity, capable of accommodating more food items, while the VHes-5 is designed for smaller operations or limited spaces, providing versatility in the kitchen. Both models come with digital control panels for easy temperature adjustments and monitoring, ensuring that chefs can maintain optimal conditions at all times.

Moving on to the 1220, 610, and 714 models, these units cater to diverse holding needs within foodservice operations. Each model is designed to be user-friendly, with clear digital displays and intuitive controls that allow chefs to quickly set and adjust holding temperatures. The 1220 model is particularly popular for its spacious design, which supports larger quantities of food, making it ideal for bustling kitchens and catered events.

The 610 and 714 models are engineered for flexibility, allowing operators to effectively manage their food items in various settings. Their compact sizes combined with smart technology make them an excellent choice for both front-line service environments and back-of-house operations. Notably, all these models support multiple food types, enabling establishments to hold everything from vegetables to protein dishes without compromising quality.

In summary, Alto-Shaam’s VHes series, including the VHes-10, VHes-5, 1220, 610, and 714, integrates cutting-edge technologies such as Halo Heat and efficient designs into versatile equipment. With an emphasis on energy savings, precise temperature control, and user convenience, these models are vital for any foodservice operation seeking to elevate their food holding and serving capabilities.