Multiquip STXD6i operation manual Components, Indicators

Page 18

components

2

1

3

 

4

7

5

14

16

13

15

28

 

12

27

17

20

8

6 18

9

11

26

10

25

24

23

19

21

22

Figure 4. Components (Front)

1.Seat — Place for operator to sit. Trowel blades will not rotate unless operator is seated. Seat is adjustable.

2.Stop Lamp (Red) — Used to relay trouble codes information that is severe enough to warrant stopping the trowel.

3.Warning Lamp (Amber) — Used to relay trouble code information that is reporting a problem with the system but the trowel need not be immediately stopped.

4.Indicators:

Oil Indicator Light — Not connected on this machine.

Water Temperature Light — Lights red when water temperature is high.

Charge Indicator — Lights red when electrical system is not charging properly.

Aux 1 — Cold start lamp, indicates when cold start sequence is enabled.

Aux 2 — Filter Condition lamp Indicates when hydraulic filter needs serviced

Cold Start Aid — Indicates when engine cold start aid is enabled.

5.Throttle Switch — Controls the speed of the engine. Press up to increase engine speed (high). down to decrease engine speed (low).

6.Fuel/Water Separator — Separates water, dirt and sludge from fuel preventing engine component wear.

7.Cruise Control Switch — Press this switch to engage the cruise control. Press again to disengage.

8.Pitch Block — (Behind grill guard) Measure at the service port and adjust pitch pressure at the pitch block.

9.Ignition Switch — With key inserted, turn switch clockwise to start engine.

10.Foot Pedal — Controls blade speed. Slow blade speed is accomplished by slightly depressing the foot pedal. Maximum blade speed is accomplished by fully depressing the foot pedal.

11.Removable Steps (left and right) — Provides for safe footing for mounting and dismounting trowel. When removed, provides access to spider and blade assemblies.

12.Lights — Six low voltage halogen lights are provided with this unit.

13.Grab Handles — Use to assist safe mounting and dismounting trowel.

14.Lift Loops — Located on both the left and right sides of the main frame. Used when the trowel must be lifted onto a concrete slab.

15.Hour Meter — Indicates number of hours machine has been used.

16.Retardant Spray Control Buttons (left and right) — When pressed allows retardant spray to flow through the spray nozzle located at the front of the machine.

page 18 — stxd6i RIDE-ON TROWEL• operation manual — rev. #0 (03/23/12)

Image 18
Contents Model stxd6i Proposition 65 warning Silicosis/respiratory warnings Silicosis WarningTable of Contents Specifications are subject to change without noticePage Training checklist Training checklistCompletely Daily pre-operation checklist Daily pre-Operation checklistSafety Information SafeTy messagesGeNeRaL safeTy Order Form PT-160 TROWeL safeTyENgINe safeTy Before servicing equipmentFueL safeTy BaTTeRy safeTy„ Use well-insulated gloves when picking up the battery Lifting TRaNspORTINg safeTyTOWINg safeTy „ NeveR lift trowel with the operator on the machineEmission control Label ENvIRONmeNTaL safeTy/decOmmIssIONINgEmIssIONs INfORmaTION Label must remain with the engine for its entire lifeLifting and transporting Lifting the trowelTransporting the trowel Specifications Trowel SpecificationsEngine Specifications Width in. cm DimensionsTrowel Dimensions This value includes the seat height TableGeneral information Indicators ComponentsToolbox Compartment Storage for tools Basic engine Oil Filler Port Remove to add fresh crankcase oilInspection Engine OilHydraulic Oil „„ The ash content must not exceed 0.01% by volume FuelDetermine if the engine fuel is low Figure Setup Battery SetupInsert the ignition key into the ignition switch Figure OperationStarting the Engine Safety Interlock Battery ManagementSafety Interlocks Engine throttleHydraulic Oil Cooler Fan Control Power managementFault Alerting Red Stop Lamp Hydraulic Oil Filter MonitoringJoystick Directional Positioning Control Joystick Result DirectionPanning Mode Manual Mode Pitch Mode Light is OffSmart Pitch Mode Blade Pitch ControlEngine ShutDown Engine ShutdownMaintenance Maintenance ScheduleAir Cleaner Air Cleaner ServiceRadiator/Cooling System Radiator Cleaning Fan Belt TensionRecommended Viscosity Grades Changing Engine Oil And FilterFuel Filter Replace the engine fuel filter element every 500 hoursOil And Fuel Lines Battery/Charging SystemFuel/Water Separator Engine Tune-UpInstalling Pans Onto Finisher Blades Long Term StorageTroubleshooting Troubleshooting Ride-On hydraulic TrowelWiring? Repair per engine repair manual Dipstick HERE’S HOW to GET Help