Multiquip STXD6i Engine throttle, Battery Management, Cold Start, Safety Interlocks, Pump Stroke

Page 25

operation

engine throttle

The engine throttle has three primary speed settings: Idle, Charge, and Operating RPM.

1.Each press of the Throttle Switch (Figure 13) steps it from idle to operating speed if operator presence is

detected.

THROTTLE

SWITCH

CRUISE CONTROL

SWITCH

Figure 13. Throttle Switch

2.The speed defaults to idle at startup or when no operator presence is detected.

3.The speed defaults to full speed when the foot pedal is depressed and operator presence is detected.

Battery Management

Idle speed is raised automatically to prevent battery drain when:

„„ Hydraulic oil cooler fan is running. „„ Lights are on

„„ Battery voltage drops below preset voltage

Cold Start

1.Idle speed is raised automatically to expedite bringing machine to operating temperature when:

„„ Hydraulic oil is below preset temperature (Oil forces across relief valve to raise oil temperature).

„„ Engine coolant temperature is below preset temperature.

2.Aux 1 on indicator will light when machine is in cold start mode.

Safety Interlocks

1.Full engine throttle is allowed only when operator presence detected.

2.Engine speed changes to idle when operator leaves the seat or the foot pedal is released for more than a set period of time.

Pump Stroke

Stroke is proportionally controlled by the foot pedal input position via feedback from the stroke position sensor.

Safety Interlock

1.Pump is automatically de-stroked if operator presence not detected.

2.Upon startup, the foot pedal will not control pump stroke if the pedal is depressed unless it has been released after start up. This prevents machine from unintentionally moving when started.

3.Pump is automatically de-stroked if error is detected from foot pedal sensor.

4.Stroke position is directly controlled by foot pedal if error is detected from the stroke sensor.

cruise control

Setting the Cruise Control will set and maintain a set pump stroke position command.

1.Press the cruise control switch (Figure 14) to engage the cruise control. The cruise control switch LED indicator lights when cruise control is engaged.

THROTTLE

SWITCH

CRUISE CONTROL

SWITCH

Figure 14. Cruise Control Switch

2.Press the cruise control switch again to disengage the cruise control. The cruise control switch LED indicator will turn off when cruise control is disengaged.

3.The cruise control can also be disengaged by

STXD6i RIDE-ON TROWEL • operation manual —rev. #0 (03/23/12) — page 25

Image 25
Contents Model stxd6i Proposition 65 warning Silicosis Warning Silicosis/respiratory warningsSpecifications are subject to change without notice Table of ContentsPage Training checklist Training checklistCompletely Daily pre-Operation checklist Daily pre-operation checklistSafeTy messages Safety InformationGeNeRaL safeTy ENgINe safeTy TROWeL safeTyOrder Form PT-160 Before servicing equipmentBaTTeRy safeTy FueL safeTy„ Use well-insulated gloves when picking up the battery TOWINg safeTy TRaNspORTINg safeTyLifting „ NeveR lift trowel with the operator on the machineEmIssIONs INfORmaTION ENvIRONmeNTaL safeTy/decOmmIssIONINgEmission control Label Label must remain with the engine for its entire lifeLifting the trowel Lifting and transportingTransporting the trowel Trowel Specifications SpecificationsEngine Specifications Trowel Dimensions DimensionsWidth in. cm This value includes the seat height TableGeneral information Components IndicatorsToolbox Compartment Storage for tools Oil Filler Port Remove to add fresh crankcase oil Basic engineEngine Oil InspectionHydraulic Oil Fuel „„ The ash content must not exceed 0.01% by volumeDetermine if the engine fuel is low Figure Battery Setup SetupOperation Insert the ignition key into the ignition switch FigureStarting the Engine Safety Interlocks Battery ManagementSafety Interlock Engine throttleFault Alerting Red Stop Lamp Power managementHydraulic Oil Cooler Fan Control Hydraulic Oil Filter MonitoringControl Joystick Result Direction Joystick Directional PositioningSmart Pitch Mode Manual Mode Pitch Mode Light is OffPanning Mode Blade Pitch ControlEngine Shutdown Engine ShutDownMaintenance Schedule MaintenanceAir Cleaner Service Air CleanerRadiator/Cooling System Fan Belt Tension Radiator CleaningFuel Filter Changing Engine Oil And FilterRecommended Viscosity Grades Replace the engine fuel filter element every 500 hoursFuel/Water Separator Battery/Charging SystemOil And Fuel Lines Engine Tune-UpLong Term Storage Installing Pans Onto Finisher BladesTroubleshooting Ride-On hydraulic Trowel TroubleshootingWiring? Repair per engine repair manual Dipstick HERE’S HOW to GET Help