WhisperKool XLT 8000 Receiving & Inspecting the Unit, Customer Warranty Registration, Contents

Page 5

RECEIVING & INSPECTING THE UNIT

Customer Warranty Registration

PLEASE COMPLETE AND RETURN THE REGISTRATION/WARRANTY CARD UPON RECEIPT OF THE UNIT. By completing the Product Registration Card, you will be confirmed in our customer database ensur- ing that your information is on file to help you obtain efficient warranty service.

Please refer to pages 30 and 31 for complete terms and conditions, warranty guidelines, and policy for your WhisperKOOL Extreme Series cooling unit.

Receiving and Inspecting the Unit

Please examine the WhisperKOOL packaging for any damage to the carton. Note any damage on the original bill of lading, shipper’s receipt, or airbill. Damaged merchandise, including unstable cabinets, should not be accepted. Contact WhisperKOOL Customer Service at 1-800- 343-9463 ext.799 immediately if you have a defective or damaged product.

Do not attempt to install any unit with cosmetic damage. This includes (but is not limited to) bent flange and/or brackets. A representative will file a claim with the shipping company, arrange for a replacement unit to be shipped to you and for the original unit to be picked up. In some instances, an inspection must take place at the point of receipt, in which case you will be contacted by the shipping company to schedule an appointment to inspect the damaged goods.

Please leave the WhisperKOOL System in its original box until you are ready for installation. This will allow you to move the product safely without damaging it. When you are ready to remove the product from the box, see Installation on page 10.

Note: Save your box and all packing materials. They provide the only safe means of transporting the unit.

Contents:

•Owner's Manual

•By-Pass Plug

•Registration/Warranty Card

•Insulation Foam (4 strips)

•8 - 1 3/4" Screws (18 for WK 6000 & 8000)

•Power Cord

•Drain Line with Brass Fitting

•Thermostat

Page 3

XLT 020111

Image 5

Contents XLT Page Owners Please Note Table of ContentsHow does the WhisperKOOL System Work? What is the WhisperKOOL System?Introduction Contents Customer Warranty RegistrationReceiving & Inspecting the Unit Receiving and Inspecting the UnitQuick Start Guide Wall & Ceiling Framing Preparing the Wine CellarDoor Unobstructed AirflowMounting the Unit Ventilation Ambient Temperature FactorCut horizontal lines from stud to stud Tools NeededMark the horizontal lines with a level Frame the hole with two-by-four supports Cut vertical lines along the inside edge of the studsElectrical Needs InstallationElectrical Outlet Sizing Unit to RoomApplying Insulation Tape Testing UnitLiquid Measuring Thermostat System Attach precut foam tape to the unit’s flangePlacement of Unit Installing ThermostatPower Switch Using the Whisperkool SystemCondensate Evaporator Switch Location of control switchesTo Use the thermostat Liquid Measuring Thermostat SystemOperation PDT JR Operating InstructionsButtons PDT PDT Operating InstructionsMaintenance Maintenance ScheduleNormal Operation Humidity Control85F Max Using the Thermostat ControllerDucting Try this first Troubleshooting GuideAirflow Cool air drops and exits beneath door Door SealAir flows on both sides of the wall Mount WhisperKOOL high in the room Unit MountingThermostat Condensation Power RequirementsIcing Up DrainlineConsumer Care Program Repairing Units Removing RivetsGeneral Inspection Troubleshooting ChecklistUnit is Not Cooling Sufficiently or Not Cooling at All Specific Performance IssuesDo not Exceed 24HRS on Bypass Plug Temperature Differential TestingEvaporator Front Side Condenser Back Side Temperature / Test timeInlet AIR -- Evaporator Front Side Inlet AIR -- Condenser Back SideConclusions Technical Assistance Accessories for Cooling UnitsFive 5 Year Compressor Limited Warranty Installation Terms and ConditionsProduct Installation Requirements Product Warranty Limitations and ExclusionsMaintenance Requirements ModelXLTSerial NumberA Questions or Additional InformationWhisperKOOL WhisperKOOL