WhisperKool XLT 1600 Testing Unit, Applying Insulation Tape, Liquid Measuring Thermostat System

Page 13

Carefully remove your WhisperKOOL unit from the box. Do not destroy your packing material, as it provides the only safe means of transporting the unit. Units weigh 65–100 pounds and are cumbersome for one person to carry. We recommend that you get someone else to help you during the installation process.

Testing Unit

Place the WhisperKOOL system on a tabletop to prepare it for installation and testing. Locate the by-pass plug and insert it into the thermostat plug, located on the front of the WhisperKOOL System. Next, plug the system into a live electrical outlet and turn the unit on. The system should begin cooling. The system may take up to 10 to 15 minutes before running cool. Once the operation has been tested, turn the unit off, unplug the unit from the electrical outlet, remove the by-pass plug, and install thermostat.

Note: If the system does not seem to be running cool after 15 minutes, please refer to the Troubleshooting Guide on page 19.

Test Plug

Before installation, use the by-pass

test plug to test the unit.

Adhesive Covering

Foam Tape

Flange

 

Applying Insulation Tape

Locate the four precut pieces of black foam tape included with your system. There should be two larger pieces and two smaller pieces. Start with the large pieces. Peel back the white-paper adhesive covering, and attach the large pieces to the sides of the unit flange. Then follow with the two smaller pieces on the top and bottom. This foam creates a tight seal between the unit’s flange and the wall (see illustration).

Note: Failure to install foam strips may void the warranty.

Attach precut foam tape to the unit’s flange.

Liquid Measuring Thermostat System

To assure a consistent temperature, place bottle probe approximately 3 feet away from the air output and not in the flow of the air.

.

Page 11

XLT 020111

Page 12 Page 14
Image 13
Page 12 Page 14
Contents XLT Page Owners Please Note Table of ContentsIntroduction What is the WhisperKOOL System?How does the WhisperKOOL System Work? Contents Customer Warranty RegistrationReceiving & Inspecting the Unit Receiving and Inspecting the UnitQuick Start Guide Wall & Ceiling Framing Preparing the Wine CellarMounting the Unit Unobstructed AirflowDoor Ventilation Ambient Temperature FactorMark the horizontal lines with a level Tools NeededCut horizontal lines from stud to stud Frame the hole with two-by-four supports Cut vertical lines along the inside edge of the studsElectrical Needs InstallationElectrical Outlet Sizing Unit to RoomApplying Insulation Tape Testing UnitLiquid Measuring Thermostat System Attach precut foam tape to the unit’s flangePlacement of Unit Installing ThermostatPower Switch Using the Whisperkool SystemCondensate Evaporator Switch Location of control switchesTo Use the thermostat Liquid Measuring Thermostat SystemButtons PDT JR Operating InstructionsOperation PDT PDT Operating InstructionsMaintenance Maintenance ScheduleNormal Operation Humidity ControlDucting Using the Thermostat Controller85F Max Airflow Troubleshooting GuideTry this first Air flows on both sides of the wall Door SealCool air drops and exits beneath door Thermostat Unit MountingMount WhisperKOOL high in the room Condensation Power RequirementsIcing Up DrainlineConsumer Care Program Repairing Units Removing RivetsGeneral Inspection Troubleshooting ChecklistUnit is Not Cooling Sufficiently or Not Cooling at All Specific Performance IssuesDo not Exceed 24HRS on Bypass Plug Temperature Differential TestingEvaporator Front Side Condenser Back Side Temperature / Test timeInlet AIR -- Evaporator Front Side Inlet AIR -- Condenser Back SideConclusions Technical Assistance Accessories for Cooling UnitsFive 5 Year Compressor Limited Warranty Installation Terms and ConditionsProduct Installation Requirements Product Warranty Limitations and ExclusionsMaintenance Requirements WhisperKOOL Questions or Additional InformationModelXLTSerial NumberA WhisperKOOL
Top Page Image Contents