WhisperKool Essential Airflow and Mounting Guide for WhisperKOOL Refrigeration Models
Page 8

Unobstructed Airflow

Unobstructed airflow to and from the unit is a critical factor in the unit’s overall performance. Make sure there is a three-foot clearance in the front of the unit, as fans blow down at an angle and should not be obstructed by racking. There should be a minimum three-foot horizontal clear- ance from the rear of the unit as well. This will assure that the unit can move the air around in an efficient manner. Avoid the attempt to camou- flage the unit by installing racking in front of the unit. This will restrict airflow and thus the unit’s ability to work efficiently.

Mounting the Unit

The unit should be mounted within 18 inches of the top of the room in order to achieve suf- ficient cooling. As the room cools down, the warm air will rise to the ceiling. Mounting the WhisperKOOL high in the room will create a consistently cool environment by capturing the warm air and replacing it with cool air. Mount- ing the unit low in the room will result in a tem- perature variation in the room due to the unit’s inability to draw warm air from the ceiling of the cellar to the unit itself.

Exhaust Room

Front of

Exhaust

WhisperKOOL

 

Intake

Wine Cellar

Door

An exterior grade (1 3/4”) door must be installed as a cellar door. It is very important that weather strip- ping is attached to all 4 sides of the door jam. A bottom “sweep” or threshold is also required. The door must have a very good seal to keep the cool cellar air from escaping out of the cellar. One of the most common problems with cooling units running continually is due to the door not sealing properly. In cases where glass doors are used and the room size is close to the recommended unit size, the next larger size WhisperKOOL should be used. This will compensate for the insulation loss due to the lower insulating rating of glass.

Page 6

XLT 020111

Page 7 Page 9
Image 8
Page 7 Page 9
Contents XLT Page Table of Contents Owners Please NoteHow does the WhisperKOOL System Work? What is the WhisperKOOL System?Introduction Customer Warranty Registration ContentsReceiving & Inspecting the Unit Receiving and Inspecting the UnitQuick Start Guide Preparing the Wine Cellar Wall & Ceiling FramingDoor Unobstructed AirflowMounting the Unit Ambient Temperature Factor VentilationCut horizontal lines from stud to stud Tools NeededMark the horizontal lines with a level Cut vertical lines along the inside edge of the studs Frame the hole with two-by-four supportsInstallation Electrical NeedsElectrical Outlet Sizing Unit to RoomTesting Unit Applying Insulation TapeLiquid Measuring Thermostat System Attach precut foam tape to the unit’s flangeInstalling Thermostat Placement of UnitUsing the Whisperkool System Power SwitchCondensate Evaporator Switch Location of control switchesLiquid Measuring Thermostat System To Use the thermostatOperation PDT JR Operating InstructionsButtons PDT Operating Instructions PDTMaintenance Schedule MaintenanceNormal Operation Humidity Control85F Max Using the Thermostat ControllerDucting Try this first Troubleshooting GuideAirflow Cool air drops and exits beneath door Door SealAir flows on both sides of the wall Mount WhisperKOOL high in the room Unit MountingThermostat Power Requirements CondensationIcing Up DrainlineRepairing Units Removing Rivets Consumer Care ProgramTroubleshooting Checklist General InspectionSpecific Performance Issues Unit is Not Cooling Sufficiently or Not Cooling at AllTemperature Differential Testing Do not Exceed 24HRS on Bypass PlugTemperature / Test time Evaporator Front Side Condenser Back SideInlet AIR -- Evaporator Front Side Inlet AIR -- Condenser Back SideConclusions Accessories for Cooling Units Technical AssistanceInstallation Terms and Conditions Five 5 Year Compressor Limited WarrantyProduct Warranty Limitations and Exclusions Product Installation RequirementsMaintenance Requirements ModelXLTSerial NumberA Questions or Additional InformationWhisperKOOL WhisperKOOL
Top Page Image Contents