WhisperKool 5000 owner manual Anti-Frost, Alarm

Page 34

SET 1. Press the “Set” button once and it will display the Set Point. After approximately 5 sec- onds, the display will return to normal operation and display the Bottle Probe tempera- ture.

2.Standard Controller - Press and hold the “Set” button for 3-5 seconds until the set point is displayed and the °F symbol starts blinking. Next press the “UP or Down” arrows to change the Set Point. Next press the “Set” button once and the Set Point numbers and the °F on the display will blink to confirm the new Set Point setting.

3.Press and hold the “Set” button during the display of the Hi/Low “Temperature Data His- tory” (hold button unit “rst” blinks on display), and it will erase the past recorded data file and start recording, from the current time and temperature.

4.Press the “Set” and the “Down Arrow” buttons simultaneously, for 10-15 seconds, and you will access the “Customer Preference Selection Mode” (CPSM). The CPSM allows the customer to “Fine Tune” the Control Operating System to their applicable choice.

 

Anti-Frost

The Anti-Frost Cycle is automatically activated when the evaporator temp has reached a low

 

 

 

 

temp of 26° and has sustained that temp for a period of five minutes. During this cycle the

 

 

 

 

 

 

 

 

compressor and condenser fans will turn off and the evaporator fans will continue to run.

 

 

 

 

Once the temperature of the evaporator gets back up to 40° the cycle will deactivate and

 

 

 

 

the system will revert back to normal operating conditions.

 

 

 

 

 

 

At the beginning of the cycle the

 

 

symbol will be illuminated and the

 

symbol is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

illuminated during the anti-frost cycle.

 

 

 

 

 

 

 

 

 

 

 

 

 

Alarm

The Alarm symbol is shown when the system encounters an issue that needs attention, the

 

 

 

 

displayed alarm codes are explained below.

 

 

 

 

Alarm Codes

 

 

 

Message

Cause

Solution

“P1”

Bottle Probe is Unplugged

Attach Bottle Probe to Unit

 

 

Faulty Bottle Probe Connection

1. Check Bottle Probe attachment at circular connector

 

 

 

2. Check Bottle Probe connection at green terminal block on

 

 

back of controller

 

Defective Bottle Probe

Replace the Bottle Probe

“P2”

Faulty Evaporator Probe

Check Evaporator Probe connection at green terminal block on back of

 

Connection

controller

 

Defective Evaporator Probe

Replace the Evaporator Probe

“HA”

Defective Bottle Probe

Replace the Bottle Probe

 

The Bottle Probe is sensing a

Allow the room to warm up which will increase the temperature of the

“LA”

temperature of 4° below the set

wine

 

point

 

 

Defective Bottle Probe

Replace the Bottle Probe

“POF”

The keypad is locked

Hold “Up” and “Down” buttons for 3 to 5 seconds to disable, “PON”

 

 

should appear

Page 32

EXti 110111

Image 34
Contents Extreme 5000 Page Table of Contents Quick Reference Guide Front / Side ViewFully Ducted Front / Side View 8000 / 8000 Rear / Side View Compressor Access Panel Standard Controller Layout Model Unit SpecificationsFAN Speed Reference Low Med HighIntroduction Receiving & Inspecting the Unit Review the Packing Slip to Verify ContentsCheck the Box for the following contents 5000 Receiving and Inspecting the UnitQuick Start Guide Insulation Preparing the Wine CellarVapor Barrier Unobstructed Airflow Mounting the UnitDoor and Door Seal Ventilation Air Intake Cellar Wall Ambient Temperature FactorUsing any other ducting system will void the warranty Exhaust FanElectrical Needs PRE-INSTALLATIONElectrical Inlets Preparing the Installation Location Minimum Tools NeededSingle Piece Mounting Bracket Preparing the System for InstallationMounting Bracket Installation Applying Insulation Tape8000 Mounting FlangesFlush Installation Exterior Grille InstallationNon-Flush Installation Optional Exterior Grille8000 Installing the System THROUGH-THE-WALL InstallationBack of Unit General Duct Recommendations Ducting OverviewUse of Ductwork Location of Supply and Return GrillesThree-Quarter Duct Configuration Wine Cellar Ducting ConfigurationsHalf Duct Configuration Wine Cellar Adjacent RoomFully Ducted Attic Mounted SystemInstalling the Duct Plenums Remote Controller Installation Mounting Bracket Condensation Drain Line Tube Failure to install the drain line voids the warrantyDrain Line Drain LineLiquid Measuring Thermostat System Liquid Measuring Thermostat SystemSelf-Calibrating Probe To Use the thermostat59/59 60/61 Multi FAN Speed Control57/57 System Operation Up and Down Button/Symbol Normal FunctionsStandard Controller Functions ArrowsAlarm Anti-FrostPage Standard Remote Controller Functions Button Normal FunctionsCheck Evaporator Probe connection at green terminal block on Cpsm Mode Remote Wire Schematic Maintenance Schedule Unit does not run/power up Possible Cause Solution Cellar Temperature is to Warm Possible Cause SolutionPossible Cause Solution Unit leaks water Possible Cause SolutionUnit runs but does not cool Possible Cause Solution Compressor short cycles Possible Cause SolutionTechnical Assistance Accessories for Cooling UnitsContact WhisperKOOL Customer Service Condensate Pump KitInstallation Terms and Conditions WhisperKOOL Cooling SystemProduct Installation Requirements Model Serial NumberA Installed by Date Sales and USE TAXPage Page WhisperKOOL