Andrew ES45T manual Overview, Getting Started

Page 6

Getting Started

Overview

Warnings

The installation, operation and maintenance of the 4.5-Meter Earth Station Antenna requires qualified personnel. Andrew installation, operation and maintenance instructions are illustrated for such personnel. Additionally, the antenna should be inspected by qual- ified personnel to verify proper installation, maintenance and condition of equipment as described in Preventative Maintenance. The basic equipment and accessories are either manufactured or design controlled by Andrew Corporation.

The prerequisite information necessary for the 4.5-Meter Earth Station Antenna can be found in this section. Furthermore, this section should be reviewed before performing the installation, operation or maintenance. Warnings, recommended tools and the anten- na parts can be verified and/or determined with such a review.

When installing the 4.5-Meter Earth Station Antenna, be conscious of the warnings pre- sented below. For further information or clarification of this information, contact the Customer Service Center at one of the phone numbers listed. The warnings are as fol- lows:

1.Electrical shock from voltages used in this antenna system may cause personal injury or death. Prior to making any electrical connections or performing maintenance or repair, ensure that the power is removed. Electrical connections should only be made by qualified personnel in accordance with local regulations.

2.Installation of antenna may require persons to work at elevated work stations. Whenever persons are working at eight or more feet above the ground and not on a guarded platform, they should wear safety belts with at least one (preferably two) lan- yards.

3.Never stand underneath any object while it is being lifted.

4.Always wear a hard hat, especially if someone is above you.

5.Make sure no person is in or under the reflector while it is being lifted or positioned; personal injury can result if the reflector assembly falls.

6.Personnel should never be hoisted in or out of the reflector by crane; personal injury may result.

7.Andrew earth station antennae supplied to standard product specifications will survive

125mph winds in any operational position in moderate coastal/industrial areas. Severe conditions require additional protection. Should it be expected that winds will exceed

125mph, it is recommended that Andrew antennae be steered to specific azimuth and elevation orientations to minimize wind forces upon the structure and thereby increase the probability of survival.

8.It is recommended that all cross axis-waveguide and coaxial cables are secure such that high winds will not cause excessive flexing. Position the antenna to an elevation of

90degrees. The azimuth jackscrew should be placed in the center of its travel.

9.When the antenna is transmitting, severe eye injury or injury to other parts of the body can result from exposure to radio frequency (RF) energy. The antenna must be turned off before entering the area in front of the reflector and near the feed.

6

Getting Started

Image 6
Contents Meter ESA Table of Contents Introduction IntroductionCustomer Service Center Proprietary Data Information Assistance TechnicalHow to Use This Manual Overview ContentOverview Getting StartedRecommended Tools Tool Size QtyGetting Started Main Reflector Assembly Getting Started Installation Procedures Overview Foundation PreparationTensioning Step A-325 TensioningTripod Mount Step 300747 Step Upper Step Step Step Step Step ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step Step ES45T-R Reflector Assembly Reflector Leveling Procedure Step ES45T-R Reflector Assembly ES45T-R Reflector Assembly Step Feed Strut Assembly ES45T-R Reflector Assembly ES45T-R-1 Back Structure ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step Installation Procedures ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step Installation Procedures ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step ES45T-R Reflector Assembly Step Installation Procedures ES45T-R Reflector Assembly Step Feed Support Assembly Step ES45T-T Reflector Assembly ES45T-T-1 Reflector Step ES45T-T Reflector Assembly Step Top Match Markings Reflector Segment Top Match Markings Capscrew Hardware 49693 Joining Plate ES45T-T Reflector Assembly Step ES45T-T Reflector Assembly Step Reflector Leveling Procedure Line of Sight Steel Rule Elevation Reflector X 1-1/2 ES45T-T Reflector Assembly Step Feed Strut Assembly ES45T-T Reflector Assembly ES45T-T-1 Back Structure Step ES45T-T Reflector Assembly Step Installation Procedures ES45T-T Reflector Assembly Step ES45T-T Reflector Assembly Step Installation Procedures ES45T-T Reflector Assembly Step ES45T-T Reflector Assembly Step Installation Procedures ES45T-T Reflector Assembly Step Step Feed Support/Strut Assembly Polarization Adjustment Step Medium Modular Mount Overview Acquiring a Satellite Step OperationStep Step Step Manual Actuator Assembly Removal Step Overview General Cleaning Electrical Parts Preventive MaintenancePreventive Maintenance Antenna Preventive Maintenance Drive System Voltage Current Checks Step Step Pedestal Mount Bearing Pad Adjustment Preventive Maintenance Jackscrews/Motors Gear Motor/Housing Fill Drain Requirements Antenna Lubrication Chart