Blodgett 1060 Series manual GAS Hose Restraint, General export installations

Page 17

Installation

Gas Connection

GAS HOSE RESTRAINT

If the oven is mounted on casters, a commercial flexible connector with a minimum of 3/4” (1.9 cm) inside diameter must be used along with a quick connect device.

The restraint, supplied with the oven, must be used to limit the movement of the unit so that no strain is placed upon the flexible connector. With the restraint fully stretched the connector should be easy to install and quick connect.

The restraint (ie: heavy gauge cable) should be 1,000 lb. (453 kg) test load and should be attached without damaging the building. DO NOT use the gas piping or electrical conduit for the attachment of the permanent end of the restraint! Use anchor bolts in concrete or cement block. On wooden walls, drive hi test wood lag screws into the studs of the wall.

1.Mount the supplied bracket to the leg bolt just below the gas inlet. See Figure 8.

2.The clip on restraining cable can be attached to the mounting bracket.

Back of Oven

Restraint

Cable Bracket

WARNING!!

If the restraint is disconnected for any reason it must be reconnected when the oven is returned to its original position.

U.S. and Canadian installations

The connector must comply with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors For Moveable Gas Ap- pliances CAN/CGA-6.16and a quick disconnect device that complies with the Standard for Quick- Disconnect Devices for Use With Gas Fuel, ANSI Z21.41 or Quick Disconnect For Use With Gas Fuel CAN 1-6.9. Adequate means must be provided to limit the movement of the appliance without de-

pending on the connection and the quick discon- nect device or its associated piping. Adequate means must be provided to limit the movement of the appliance without depending on the connec- tion and the quick disconnect device or its associ- ated piping.

General export installations

The restraint and quick connect must conform with Local and National installation standards. Lo- cal installation codes and/or requirements may vary. If you have any questions regarding the prop- er installation and/or operation of your Blodgett oven, please contact your local distributor. If you do not have a local distributor, please call the Blodgett Oven Company at 0011-802-860-3700.

Double stacked unit shown. Use the same procedure for single units with 25” (64 cm) legs.

Figure 8

13

Image 17
Contents Series Avertissement Reputation YOU can Count on Page Table of Contents/Table des Matières BL GAS Specifications Oven Description and SpecificationsGAS Specifications IntroductionOven Components Delivery and Location InstallationDelivery and Inspection Oven LocationPackaging LEG Attachment Oven AssemblySingle Sections Double SectionsUltra Rokite Shelves Double Section AssemblyPiece Deflector Assembly Deck Seal Adjustments Associated with Initial InstallationFlue Plates Leveling the OvenGeneral export installations Canadian installationsInstalling the canopy hood draft diverter VentilationDirect Flue Arrangement Venting ProblemsInstalling the draft hood Utility Connections --- Standards and Codes GAS Piping Gas ConnectionExample Pipe Nominal Size, Inches LengthInlet Pressure Natural Propane Pressure Regulation and TestingKPa Manifold Pressure Natural Propane KPaGAS Hose Restraint Safety Tips Safety InformationWhat to do in the event of a power failure General safety tipsOperation Oven ControlControl Description General Guidelines for Operating Personnel Cook Times and Temperatures Cook TemperaturesCook Time Baking TipsCleaning and Preventative Maintenance MaintenanceCleaning the Oven Preventative MaintenancePossible Causes Suggested Remedy Troubleshooting GuideTroubleshooting Guide Specifications Pour GAZ BL Specifications Pour GAZDescription et Spécifications du Four Gaz Naturel Gaz Propane Unités US Unités SIÉléments du Four Implantation DU Four Livraison et ImplantationLivraison ET Inspection Emballage Montage du FourAssemblage DES Pieds Fixation DES RoulettesDES Plaques EN Ultra Rokite Montage DE LA Section DoubleMontage DU Déflecteur EN Trois Parties Joint DE Plaque Réglages À Faire Lors DE ’INSTALLATION InitialePlaques DE Cheminée Mise À Niveau DES FoursInstallation du déviateur de tirage Installation aux États-- Unis et au CanadaAvertissement Hotte D’ÉVACUATION Type VoûteEN Prise Directe Installation de la hotte de tirageMents brûleurs Problêmes DE LA VentilationBranchements de Service --- Normes et Codes Branchement de Gaz Longeur Dimensions nominales De conduit PiedsConduit DE GAZ ExempleKPa Pression au collecteur Gaz Naturel Gaz Propane Réglage ET Test DE PressionPression à l’entrée Gaz Naturel Gaz Propane Retenue DU Tuyau DE GAZ Information de Sécurité UtilisationConseils DE Sécurité Que faire en cas de panne de secteurUtilisation Les Commandes du FourDescription DES Commandes Temps ET Températures Consignes Générales à l’Intention des UtilasateursLa Température de Cuisson La Durée de CuissonNettoyage et Entretien Préventif EntretienNettoyage DES Fours Entretien PréventifCauses Probables Suggestion Guide de Détection des PannesGuide de Détection des Pannes

1060 Series specifications

The Blodgett 1060 Series stands out in the commercial food service industry as a highly efficient and versatile cooking solution. Designed primarily for high-volume establishments, this series is known for its combination of performance, durability, and user-friendly features.

One of the standout features of the Blodgett 1060 Series is its advanced convection technology. Utilizing a powerful fan and a unique airflow design, these ovens ensure even heat distribution, resulting in perfectly cooked products every time. This technology significantly reduces cooking times, allowing busy kitchens to increase productivity while maintaining quality.

Moreover, the 1060 Series incorporates a robust construction designed to endure the daily rigors of a commercial kitchen. Crafted with stainless steel, both the interior and exterior boast incredible resistance to rust and corrosion, ensuring longevity and ease of maintenance. The oven’s smooth surfaces make it simple to clean, while also contributing to its sleek aesthetic, making it an excellent choice for front-of-house cooking.

Another impressive characteristic of the 1060 Series is its precise temperature control. The digital display allows chefs to set and monitor temperatures with accuracy, facilitating consistency across various cooking applications. Additionally, the ovens in this series come equipped with programmable controls, enabling users to save specific cooking temperatures and times for different recipes, thus streamlining the cooking process.

The Blodgett 1060 Series also prioritizes energy efficiency. With improved insulation and heating technology, these ovens consume less energy compared to traditional models, which translates into lower utility bills without sacrificing performance.

Versatility is another hallmark of the 1060 Series. It accommodates a variety of cooking methods, from baking and roasting to broiling. Its spacious interior can hold numerous pans simultaneously, catering to the needs of high-demand environments.

In summary, the Blodgett 1060 Series is a powerhouse of efficiency and innovation. Its advanced convection technology, durable construction, precise controls, and energy-efficient design make it an indispensable tool for any commercial kitchen. Whether for baking, roasting, or broiling, this series is engineered to meet the rigorous demands of the food service industry while ensuring top-quality results. With the Blodgett 1060 Series, culinary professionals can deliver exceptional meals quickly and consistently.