Texas Instruments TAS3002 manual Digital-to-AnalogConverter, DAC Output Performance Data

Page 49

8.8 Digital-to-Analog Converter

TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V, fS = 48 kHz, input = 0 dB-fSsine wave at 1 kHz

PARAMETER	TEST CONDITIONS	MIN	TYP MAX	UNIT

SNR (EIAJ)	A weighted	94	99	dB

Dynamic range	−60 dB, 1 kHz	92	96	dB

Signal to (noise + distortion) ratio	0 dB, 1 kHz, 20 Hz to 20 kHz		83	dB

Power supply rejection ratio	1 kHz		50	dB

Idle channel tone rejection			+118	dB

Intermodulation distortion			−75	dB

Frequency response		−0.5	+0.5	dB

Deviation from linear phase			±1.4	degree

DAC crosstalk			−96	dB

Jitter tolerance			150	ps

Full scale, single-ended, output voltage range			1.9	VPP
DC offset		−7.0	7.0	mV

8.9 DAC Output Performance Data

TA = 25°C, AVDD = 3.3 V, DVDD = 3.3 V

The output load resistance is connected through a dc blocking capacitor.

	PARAMETER	TEST CONDITIONS	MIN TYP	MAX	UNIT

Output load resistance			10		kΩ

Output load capacitance				25	pF

VCOM internal resistance (see Note 4)			1		kΩ

VCOM output CLOAD			10	100	∝F

VRFILT internal resistance (see Note 5)			1		kΩ

NOTES: 4.	VCOM may vary during power down.
5.	VRFILT must never be used as a voltage reference.

8−5

Image 49

Contents TAS3002 Data ManualDigital Audio Processor With Codec 2001IMPORTANT NOTICE 1 Introduction 1.2Features1.1 Description 1.3Functional Block Diagram Figure 1−1. TAS3002 Block Diagram 1.5 Terminal Functions 1.4 Terminal AssignmentsFigure 1−2. TAS3002 Terminal Assignments Table 1−1. TAS3002 Terminal FunctionsTable 1−1. TAS3002 Terminal Functions Continued Page 2.1 Serial Interface Formats 2 Audio Data FormatsTable 2−1. Serial Interface Options 2.2 Digital Output Modes … … … …… … … … … … … …Figure 2−2. I 2S Serial-InterfaceFormat 2.2.2I2S Serial-InterfaceFormat… … … … … … … …… … … … 2.2.3MSB-Left-Justified, Serial-InterfaceFormat… … … … … … … …PARAMETER 2.3 Switching CharacteristicsUNIT tcSCLK SCLK LRCLK tdSDOUT SDOUT1 SDOUT2 SDOUT0Page 3.1 Analog Input 3 Analog Input/Output3.2 Analog Output 3.2.1Direct Analog OutputFigure 3−2. VCOM Decoupling Network 3.2.2Analog Output With GainFigure 3−3. Analog Output With External Amplifier TAS3002 3.2.3Reference Voltage FilterFigure 3−4. TAS3002 Reference Voltage Filter Page 4 Audio Control/Enhancement Functions 4.1 Soft Volume Update4.2 Software Soft Mute 4.3 Input Mixer Control4.5 Treble Control 4.4 Mono Mixer ControlFigure 4−1. TAS3002 Mixer Function 4.7 De-EmphasisMode DM 4.6 Bass ControlFigure 4−2. De-EmphasisMode Frequency Response Table 4−1. Analog Control Register Description 4.8 Analog Control Register 40h4.9.1Loudness Biquads 4.9 Dynamic Loudness Contour4.9.2Loudness Gain 4.9.3Loudness Contour Operation4.11 AllPass Function 4.10 Dynamic Range Compression/Expansion DRCE4.13 Main Control Register 2 43h 4.12 Main Control Register 1 01hTable 4−2. Main Control Register 1 Description Table 4−3. Main Control Register 2 DescriptionPage 5 Filter Processor Figure 5−1. Biquad Cascade Configuration5.1 Biquad Block 5.1.1Filter CoefficientsPage 6.1 Introduction 6 I2C Serial Control Interface6.2 I2C Protocol Figure 6−1. Typical I 2C Data Transfer Sequence6.3.1Write Cycle Example 6.3 OperationTable 6−1. I 2C Protocol Definitions Table 6−2. I 2C Address Byte Table6.3.3I2C Wait States 6.3.2TAS3002 I2C Readback Example6.4.1Block Write Protocol 6.4 SMBus Operation6.4.2Write Byte Protocol Table 6−3. I 2C Wait States6.4.4TAS3002 SMBus Readback 6.4.3Wait StatesPage 7.2.1Power-UpSequence 7.2 Power-Up/Power-DownReset7.2.2Reset 7 Microcontroller OperationFigure 7−1. TAS3002 Reset Circuit 7.2.3Reset Circuit7.2.4Fast Load Mode TAS30027.2.5Codec Reset 7.3 Power-DownModeFigure 7−2. Power-DownTiming Sequence 7.3.1Power-DownTiming Sequence7.4 Test Mode 7.5 Internal InterfaceTable 7−1. GPI Terminal Programming 7.6.2GPI ArchitectureRestore Volume and MCR Figure 7−3. Internal Interface Flow ChartStart Power Up Initialize Default EEPROM Slave Write GPI Power DownTable 7−2. 512-ByteEEPROM Memory Map 2.0 Channels 7.7 External EEPROM Memory MapsBYTE NUMBER ADDRESSFUNCTION TAS3002NUMBER TAS3002 ADDRESSFUNCTION CATEGORYNUMBER TAS3002 ADDRESSFUNCTION CATEGORYStatic Digital Specifications 8 Electrical Characteristics8.2 Recommended Operating Conditions 8.4 ADC Digital Filter Figure 8−1. ADC Digital Filter Characteristics8.5 Analog-to-DigitalConverter Figure 8−4. ADC High-PassFilter Characteristics8.7 DAC Interpolation Filter 8.6 Input Multiplexer8.9 DAC Output Performance Data 8.8 Digital-to-AnalogConverterFigure 8−7. I 2C Bus Timing 8.10 I2C Serial Port Timing CharacteristicsFigure 9−1. Stereo Application 9 System DiagramsTAS3002 ClockFigure 9−2. TAS3002 Device, 2.1 Channels TAS3001TAS3002 PFB S-PQFP-G48 10 Mechanical InformationPLASTIC QUAD FLATPACK 10−2