Electrolux EOG 900 manual Side View Front View

Page 40

INSTALLATION Solid Pipe Installation

FITTING THE APPLIANCE AND CABINET.

1Make suitable arrangements for gas and electrical supplies into the installation site. Preferably a junction box or a 3 pin earthed socket should be situated at the back of the cabinet below the oven.

2Fit cabinet as Fig. 1, making sure that it is level.

3When unpacking the oven keep it on it's polystyrene base until it is put into the cabinet to avoid damage. NOTE: It is imperative that the appliance is left in the base to protect both the appliance and the floor. Do not allow young children to play with any part of the packaging.

4

Remove the oven and grill doors. (See section B on

GAS INLET SUPPLY BLOCK

 

page 43).

 

 

5

Solid gas pipe installation:

 

 

 

i)

Remove the fascia control panel (See section A

 

 

 

 

on page 43).

 

 

 

ii) Slacken and remove the union nut on the gas

 

 

 

 

supply elbow on the right hand side of the

 

 

 

 

control panel. See Fig.7.

 

 

 

 

 

680

 

iii) Remove the two screws on the gas inlet block

 

 

 

 

 

 

Fig.3.

 

 

 

iv)

Withdraw the gas inlet block and pipe assembly

 

 

 

 

from the back of the appliance

 

 

 

v)

Remove the union elbow from the inlet block

 

 

 

 

and pipe assembly. The elbow will be required

 

 

 

 

in the final installation.

 

 

 

vi)

The union elbow should be connected to the

120

 

 

 

gas supply pipe via a standard ¼"B.S.P. straight

Fig.3

 

 

connector.

6 Install the gas supply pipe on site complete with the

union elbow (See Fig.4). Note the orientation of the

120

 

elbow, the connection must be upwards.

 

7Position the appliance in front of the cabinet and run the supply cable (See Section 2) through the cabinet and connect to the junction box or socket. Ensure that the supply is isolated at this stage.

N.B. Two people will be required to carry out the lifting procedure. Warning: Do not attempt to lift this appliance by the handles.

8Lift the appliance into the cabinet making sure the gas supply pipe enters the duct in the rear of the appliance and the cable is not trapped by the appliance. Push the appliance as far back as it will go. Ensure the supply pipe comes through the control panel and pull through any slack cable.

9Centralise and fix the appliance to the cabinet using six wood screws in the position indicated in Fig.2.

10Tighten the union nut into the supply elbow.

11Carry out gas soundness check .

NOTE: Check supply pressure before fitting fascia (See Section 3).

SIDE VIEW

FRONT VIEW

75

 

225

 

mm

Fig.4

795

40

Image 40
Contents ModelEOG900 Introduction For your safetyG 9 0 Contents Installing the oven For your safety Cabinet DimensionsLocation Minimum aperture widthGeneral information Cooling fan for the controlsConnectingFor your safetyto the electricity supply IgnitionOven light Please noteLighting the oven and grill GrillOven To lightTo turn off any burner Lighting the oven and grill G 9 0Grill Grill gives variable heat settingsHeat control Preheating Cooking positionsPutting food on the grid Grill shelf Shelf positions are counted from the top downwardsGrill pan and handle Grill pan is supplied with a removable handlePlate warming Oven For your safety Heat zonesOven shelves Baking trays and dishes For your safety RoastingCondensation Burner flamesOven cooking chart Cook as above but calculate weight including stuffing GasMins. per ½ kg 1 lb and 25 mins Mins. per ½ kg 1 lb and 15 mins90kg 2 lb loaves Food preparation-slow cooking Slow cookingJoints of meat and poultry Soups, casseroles and stews VegetablesMilk puddings General points for slow cooking Frozen foodsMilk and milk products, for example cream LiquidReheating Electronic Timer Electronic timerTo set the time of day To use the CountdownElectronic timer G 9 0 Setting the controls for automatic useAutomatic control To cancel an automatic programme Turn off the oven controlHints and tips for automatic cooking Care and cleaning For your safety General Do not overfill dishes or they will boil overCleaning between the outer and inner door glass To remove the outer glassWhat is wrong and why? ProblemCheck LCheckG 9 0 Problem Replacing an oven light bulb Replacing an oven light bulb G 9 0Service and spare parts 7 0 5 9 2 9 9 2Customer Care Department Installation Instructions Technical Data Important Safety Requirements Provision for Ventilation560 min 570 max Location of ApplianceFitting the Appliance and Cabinet Side View Front View Pressure Testing Connection to Electricity SupplyRE-ASSEMBLE the Appliance Removal of Fascia PanelChecking the Grill Removal of Oven or Grill DoorsTo SET the Time of DAY Automatic Operation Checking the Main OvenGeneral Note Guarantee Conditions Standard guarantee conditionsEOG 900 Contents Check List Telephone 0870 5 Electrolux Household Appliances Limited