Sherwood RD-7503 manual Speaker placement, Connecting Subwoofer PRE OUT

Page 10

RD-7503(A)2008.11.41:45PM페이지10

ENGLISH

Continued

�Connecting speaker wire

1. Strip away approx. 10 mm

2. Lossen by turning the

3. Insert the bare part of the

4. Tighten by turning it

(3/8 inch) of wire insulation,

speaker terminal counter-

wire.

clockwise.

then twist the wire ends

clockwise.

 

 

 

 

 

 

 

 

 

 

 

 

tight.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Speaker placement

Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows :

■Front left and right speakers and center speaker

•Place the front speakers with their front surfaces as flush with TV or monitor screen as possible.

•Place the center speaker between the front left and right speakers and no further from the listening position than the front speakers.

•Place each speaker so that sound is aimed at the location of the listener’s ears when at the main listening position.

■Surround left and right speakers

•Place the surround speakers approximately 1 meter (40 inches) above the ear level of a seated listener on the direct left and right of them or slightly behind.

■Surround back left and right speakers

•Place the surround back speakers at the back facing the front at a narrower distance than front speakers.

•When using a single surround back speaker, place it at the rear center facing the front at a slightly higher position (0 to 20 cm ) than the surround speakers.

•We recommend installing the surround back speaker(s) at a slightly downward facing angle. This effectively prevents the surround back channel signals from reflecting off the TV or screen at the front center, resulting in interference and making the sense of movement from the front to the back less sharp.

■Subwoofer

•The subwoofer reproduces powerful deep bass sounds. Place a subwoofer anywhere in the front as desired.

�Notes :

�When using a conventional TV, to avoid interference with the TV picture, use only magnetically shielded front

left and right and center speakers.

�To obtain the best surround effects, the speakers except the subwoofer should be full range speakers.

1.

TV or Screen

7.

Surround right speaker

2.

Front left speaker

8.

Surround back left speaker

3.

Subwoofer

9.

Surround back right speaker

4.

Center speaker

10.

Surround center speaker

5.

Front right speaker

11.

Listening position

6.

Surround left speaker

 

 

 

7. CONNECTING SUBWOOFER PRE OUT

•To emphasize the deep bass sounds, connect a powered subwoofer.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents RD-7503 Important Safety Instructions Read this Before Operating Your Unit Introduction120 Contents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1 Connecting Audio ComponentsComponent video input default settings *2 Copyright protection systemConnecting Digital INS and OUT Connecting External INSDigital input default settings Surround back speakers Connecting SpeakersFront Bi-Amp Connections Speaker placement Connecting Subwoofer PRE OUTConnecting Room 2 Outs Connecting DC Trigger OUTAC Input Cord Connecting for System ControlConnecting Sirius Connector only for North America SiriusConnect Home TunerRemote Sensor Front Panel ControlsFluorescent Display Bluetooth in Connector Setup MIC JackFront AUX in Jack UP/DOWN / buttons Numeric 0~9, +10 Input Selector buttons Universal Remote ControlsPower on button ENTER/SEARCH MODE, Select buttonsFunction Table of the Numbered Buttons Loading Batteries Entering a setup code Repeat the above steps 1 to 4 for each of your ComponentsRemoving a punch-through function Using a punch-through functionRemoving all punch-through functions To remove a macro program Programming a macro functionOperating a macro function To change a macro programListening to a Program Source OperationsBefore operation Listening with headphones When CD, F.AUX, Video 1~ 3 is selected as an input sourceMuting the sound Surround modes Stadium TheaterHall RoomEnjoying Surround Sound Dolby TruehdCancel the test tone function Adjusting each channel level with test toneEnter the test tone mode To cancel the surround mode for stereo operationRepeat the above steps 2 and 3 to adjust each channel level Adjusting the current channel levelAdjust the level of the selected channel as desired Press the Channel Level buttonMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning Manual presettingTuning to preset stations Press the MEMORY/ENTER buttonSirius Satellite Radio only for North America Press the Tuning UP+/DOWN- buttons repeatedly to select SRTo sign up, access the website at Signing up for Sirius Satellite RadioCategory search Direct search→ DIR Srch → CAT Srch → OFF Presetting channels Preset searchParental lock When tuning in the previously locked channelsTune in the channel you want to lock or unlock Recording Dubbing the audio and video signals separately onto VideoTo record audio signals Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent display Displaying the operation statusRoom 2 Source Playback Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Start play on the component related to the Room 2 sourceSelect the desired menu using the Cursor UP/DOWN buttons OSD Menu SettingsTurn the menu screen on When selecting the CH Level Setup When selecting the SPEAKER/ROOMEQSETUPWhen selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust Press the Cursor UP/DOWN buttons to select the desired itemWhen selecting the Hdmi Audio OUT When selecting the Subwoofer ModeWhen selecting the Tone Control When selecting the Cinema EQ When selecting the Momentary OSDWhen selecting the OSD Position Adjust Setting the Input Setup When selecting the menu of page 2 orWhen selecting the Audio Assign When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio ModeWhen selecting the DC Trigger When selecting the Auto SurroundWhen selecting the AV Sync When selecting the HD AudioConfirm your entry When selecting the NameTo resume its factory input source name When selecting the Parental Lock When selecting the Edit Lock Code When selecting the Auto Setup Setting the Speaker / Room EQ SetupPreparations RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration When selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Memory mode Setting the CH Level SetupRepeat the above steps 1 and 2 to adjust each channel level Reference When selecting the Night Mode Setting the Sound ParameterAuto When selecting the Panorama mode When selecting the Dolby Plii MusicRepeat the above steps 2 and 3 to adjust other parameters When selecting the Center Width controlWhen selecting the Input Setting the Multi Room SetupWhen selecting the Room When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Setup Code Table TMK RCASSS CCEMEI KLHSTS ABC NSCSAT HTSRD-7503
Top Page Image Contents