Sherwood RD-7503 manual When selecting the Subwoofer Mode, When selecting the Hdmi Audio OUT

Page 42

RD-7503(A)2008.11.41:45PM페이지42

ENGLISH

Continued

�When selecting the SUBWOOFER MODE

•"SW PLUS＋" mode is valid only when "FRONT" and "CENTER" are set to "FULL RANGE" and "SUBWOOFER" is set to "YES" on the SPEAKER/ROOM EQ SETUP menu. (For details, refer to "SETTING THE SPEAKER/ ROOM EQ SETUP" on page 51.)

NORMAL : When the low frequency signals of channels set to "FULL RANGE " are reproduced from those channels only. In this mode, the low frequency signals that are reproduced from the subwoofer channel is only the low frequency

�signals of LFE (from the multi-channel sources that contains LFE (Low Frequency Effects) channel, also called the ".1" channel) and the channels set to the setting value other than "FULL RANGE".

SW PLUS＋ : When the low frequency signals of channels set to "FULL RANGE" are reproduced simultaneously from those channels and the subwoofer channel.

In this mode, the low frequency range expands more uniformly through the room, but depending on the size and shape of the room, interference may result in a decrease of the actual volume of the low frequency range.

�When selecting the HDMI AUDIO OUT

•The HDMI connection can carry uncompressed digital video signals and digital audio signals.

Depending on whether the digital audio signals input into the HDMI IN are output from the HDMI MONITOR OUT of this receiver or not, you should set the HDMI AUDIO OUT correctly.

OFF : Not to output the HDMI digital audio signals from the HDMI MONITOR OUT of this receiver, meaning these

�signals are heard from the speakers connected to this receiver.

ON : To output the HDMI digital audio signals from the HDMI MONITOR OUT, meaning these signals are heard from the speakers of your TV.

�Note:

•When the HDMI AUDIO OUT is set to ON, no sound will be heard from the speakers connected to this receiver (except ROOM 2 speakers) even though any input source is selected.

�When selecting the TONE CONTROL

OFF : To listen to a program source without the tone effect. ("DIR" lights up.)

�

ON : To adjust the tone for your taste. ("DIR" goes off.)

◆When the TONE CONTROL is set to ON to adjust the tone (bass and treble) ①. Press the ENTER button to enter the tone adjustment mode.

42

Image 42

Contents RD-7503 Important Safety Instructions Introduction Read this Before Operating Your Unit120 Contents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1 Connecting Audio ComponentsComponent video input default settings *2 Copyright protection systemConnecting External INS Connecting Digital INS and OUTDigital input default settings Connecting Speakers Surround back speakersFront Bi-Amp Connections Speaker placement Connecting Subwoofer PRE OUTConnecting Room 2 Outs Connecting DC Trigger OUTAC Input Cord Connecting for System ControlConnecting Sirius Connector only for North America SiriusConnect Home TunerFront Panel Controls Remote SensorFluorescent Display Setup MIC Jack Bluetooth in ConnectorFront AUX in Jack UP/DOWN / buttons Numeric 0~9, +10 Input Selector buttons Universal Remote ControlsPower on button ENTER/SEARCH MODE, Select buttonsFunction Table of the Numbered Buttons Loading Batteries Entering a setup code Repeat the above steps 1 to 4 for each of your ComponentsUsing a punch-through function Removing a punch-through functionRemoving all punch-through functions To remove a macro program Programming a macro functionOperating a macro function To change a macro programOperations Listening to a Program SourceBefore operation When CD, F.AUX, Video 1~ 3 is selected as an input source Listening with headphonesMuting the sound Surround modes Stadium TheaterHall RoomEnjoying Surround Sound Dolby TruehdCancel the test tone function Adjusting each channel level with test toneEnter the test tone mode To cancel the surround mode for stereo operationRepeat the above steps 2 and 3 to adjust each channel level Adjusting the current channel levelAdjust the level of the selected channel as desired Press the Channel Level buttonMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning Manual presettingTuning to preset stations Press the MEMORY/ENTER buttonSirius Satellite Radio only for North America Press the Tuning UP+/DOWN- buttons repeatedly to select SRTo sign up, access the website at Signing up for Sirius Satellite RadioDirect search Category search→ DIR Srch → CAT Srch → OFF Presetting channels Preset searchWhen tuning in the previously locked channels Parental lockTune in the channel you want to lock or unlock Recording Dubbing the audio and video signals separately onto VideoTo record audio signals Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent display Displaying the operation statusRoom 2 Source Playback Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Start play on the component related to the Room 2 sourceOSD Menu Settings Select the desired menu using the Cursor UP/DOWN buttonsTurn the menu screen on When selecting the CH Level Setup When selecting the SPEAKER/ROOMEQSETUPWhen selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust Press the Cursor UP/DOWN buttons to select the desired itemWhen selecting the Subwoofer Mode When selecting the Hdmi Audio OUTWhen selecting the Tone Control When selecting the Cinema EQ When selecting the Momentary OSDWhen selecting the OSD Position Adjust Setting the Input Setup When selecting the menu of page 2 orWhen selecting the Audio Assign When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio ModeWhen selecting the DC Trigger When selecting the Auto SurroundWhen selecting the AV Sync When selecting the HD AudioWhen selecting the Name Confirm your entryTo resume its factory input source name When selecting the Parental Lock When selecting the Edit Lock Code Setting the Speaker / Room EQ Setup When selecting the Auto SetupPreparations RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration When selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memory modeRepeat the above steps 1 and 2 to adjust each channel level Reference Setting the Sound Parameter When selecting the Night ModeAuto When selecting the Panorama mode When selecting the Dolby Plii MusicRepeat the above steps 2 and 3 to adjust other parameters When selecting the Center Width controlWhen selecting the Input Setting the Multi Room SetupWhen selecting the Room When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Setup Code Table TMK RCASSS CCEKLH MEISTS ABC NSCSAT HTSRD-7503