Sherwood RD-7503 Entering a setup code, Repeat the above steps 1 to 4 for each of your Components

Page 18

RD-7503(A)2008.11.41:45PM페이지18

ENGLISH

USING FUNCTIONS OF REMOTE CONTROL

This remote control can control up to 6 different components.

Before operating audio and video components other than this receiver with using this remote control, the setup code for each component should be entered.

For system remote control operation, "000" was stored previously in the memory of the device button "DOCK" for Sherwood iPod dock, "DVD" for Sherwood DVD player and "TV" for Sherwood TV respectively as its factory setup code. So, you don’t need to enter its code for each Sherwood component except in such a case that its code does not work.

Entering a setup code

1. Turn on the component you want to operate.

2. Find the setup codes according to the type and the brand name of your component, referring to "Setup Code Table" on page 62.

3. Press and hold down both the ENTER button and the desired one of the DEVICE buttons for more than 1 seconds.

• The SET LED will flicker once.

Note :

The "AVR" button is unavailable for the audio components other than this receiver.

4. Enter a 3 digit code, aiming the remote control at the remote sensor on the component.

Example: When entering "001".

If entering is performed successfully, the SET LED will flicker twice.

To be sure that the setup code is correct, press the POWER ON (or STANDBY) button. If your component is turned off, the setup code is correct.

When your component is not turned off, repeat the above steps 2 to 4, trying each code for your component until you find one that works.

Notes:

If the SET LED did not flicker twice, then repeat the above steps 3 to 4 and try entering the same code again.

Manufacturers may use different setup codes for the same product category. For that reason, it is important that you check to see if the code you have entered operates as many controls as possible. If only a few functions operate, check to see if another code will work with more buttons.

5. Repeat the above steps 1 to 4 for each of your

components.

18

Image 18
Contents RD-7503 Important Safety Instructions Introduction Read this Before Operating Your Unit120 Contents Connecting Antennas System ConnectionsConnecting Video Components Hdmi High Definition Multimedia Interface connection *1 Connecting Audio ComponentsComponent video input default settings *2 Copyright protection systemConnecting External INS Connecting Digital INS and OUTDigital input default settings Connecting Speakers Surround back speakersFront Bi-Amp Connections Speaker placement Connecting Subwoofer PRE OUTConnecting Room 2 Outs Connecting DC Trigger OUTAC Input Cord Connecting for System ControlConnecting Sirius Connector only for North America SiriusConnect Home TunerFront Panel Controls Remote SensorFluorescent Display Setup MIC Jack Bluetooth in ConnectorFront AUX in Jack UP/DOWN / buttons Numeric 0~9, +10 Input Selector buttons Universal Remote ControlsPower on button ENTER/SEARCH MODE, Select buttonsFunction Table of the Numbered Buttons Loading Batteries Entering a setup code Repeat the above steps 1 to 4 for each of your ComponentsUsing a punch-through function Removing a punch-through functionRemoving all punch-through functions To remove a macro program Programming a macro functionOperating a macro function To change a macro programOperations Listening to a Program SourceBefore operation When CD, F.AUX, Video 1~ 3 is selected as an input source Listening with headphonesMuting the sound Surround modes Stadium TheaterHall RoomEnjoying Surround Sound Dolby TruehdCancel the test tone function Adjusting each channel level with test toneEnter the test tone mode To cancel the surround mode for stereo operationRepeat the above steps 2 and 3 to adjust each channel level Adjusting the current channel levelAdjust the level of the selected channel as desired Press the Channel Level buttonMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning Manual presettingTuning to preset stations Press the MEMORY/ENTER buttonSirius Satellite Radio only for North America Press the Tuning UP+/DOWN- buttons repeatedly to select SRTo sign up, access the website at Signing up for Sirius Satellite RadioDirect search Category search→ DIR Srch → CAT Srch → OFF Presetting channels Preset searchWhen tuning in the previously locked channels Parental lockTune in the channel you want to lock or unlock Recording Dubbing the audio and video signals separately onto VideoTo record audio signals Dubbing from video components ontoDigital Audio Recording with MD Recorder Other Functions Operating the sleep timerAdjusting the brightness of the fluorescent display Displaying the operation statusRoom 2 Source Playback Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Start play on the component related to the Room 2 sourceOSD Menu Settings Select the desired menu using the Cursor UP/DOWN buttonsTurn the menu screen on When selecting the CH Level Setup When selecting the SPEAKER/ROOMEQSETUPWhen selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust Press the Cursor UP/DOWN buttons to select the desired itemWhen selecting the Subwoofer Mode When selecting the Hdmi Audio OUTWhen selecting the Tone Control When selecting the Cinema EQ When selecting the Momentary OSDWhen selecting the OSD Position Adjust Setting the Input Setup When selecting the menu of page 2 orWhen selecting the Audio Assign When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio ModeWhen selecting the DC Trigger When selecting the Auto SurroundWhen selecting the AV Sync When selecting the HD AudioWhen selecting the Name Confirm your entryTo resume its factory input source name When selecting the Parental Lock When selecting the Edit Lock Code Setting the Speaker / Room EQ Setup When selecting the Auto SetupPreparations RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration When selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memory modeRepeat the above steps 1 and 2 to adjust each channel level Reference Setting the Sound Parameter When selecting the Night ModeAuto When selecting the Panorama mode When selecting the Dolby Plii MusicRepeat the above steps 2 and 3 to adjust other parameters When selecting the Center Width controlWhen selecting the Input Setting the Multi Room SetupWhen selecting the Room When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Setup Code Table TMK RCASSS CCEKLH MEISTS ABC NSCSAT HTSRD-7503