Sherwood RD-7503 manual Operations, Listening to a Program Source, Before operation

Page 21

RD-7503(A)2008.11.41:45PM페이지21

Operations

�Notes:

•Before operating this receiver with the supplied remote control, refer to "Universal Remote Controls" on page 15 for details about operation.

•Before operating this receiver, first set this unit as desired for optimum performance, doing the OSD menu setting procedures. (For details, refer to "OSD Menu Settings" on page 39.)

ENGLISH

LISTENING TO A PROGRAM SOURCE

Before operation

•Enter the standby mode.

•The STANDBY indicator lights up amber. This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the operation readiness.

•To switch the power off, push the POWER switch again.

Then the power is cut off and the STANDBY indicator goes off.

1. In the standby mode, turn the power on.

•Each time the POWER ON/STANDBY button on the front panel is pressed, the receiver is turned on to enter the operating mode (the STANDBY indicator lights up blue) or off to enter the standby mode(the STANDBY indicator lights up amber).

•On the remote control, press the POWER ON button to enter the operating mode or press the STANDBY button to enter the standby mode.

•In the standby mode, if the INPUT SELECTOR knob is rotated or the INPUT SELECTOR button is pressed, the receiver is turned on automatically and the desired input is selected.

2. Switch the speakers on.

• Then the SPEAKER indicator lights up and the sound can be heard from the speakers connected to the speaker terminals.

• When using the headphones for private listening, press the SPEAKER button again to switch the speakers off.

3. Select the desired input source.

•Each time the INPUT SELECTOR knob on the front panel is rotated, the input source changes as follows:

→TUNER ↔ CD ↔ TAPE ↔ F.AUX ↔ VIDEO 1 ←

(Frequency display)

→ BT ↔ VIDEO 3 ↔ V2/IPOD ←

•Each time the BAND button (or the TUNER button on the remote control) is pressed, the band changes as follows:

→FM ST → FM MONO → AM → SIRIUS

�When selecting the EXTERNAL IN as desired,

•Depending on the power amplifier setting for the surround back channels and the surround back speaker setting, "EXT. IN" is displayed and 8(/7/6) separate analog signals from the component connected to this input pass through the volume circuits only and can be heard from your speakers.

•Select the desired input source to cancel the external in function.

•These analog signals can be heard only, not recorded.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents RD-7503 Important Safety Instructions Introduction Read this Before Operating Your Unit120 Contents System Connections Connecting AntennasConnecting Video Components Component video input default settings *2 Connecting Audio ComponentsHdmi High Definition Multimedia Interface connection *1 Copyright protection systemConnecting External INS Connecting Digital INS and OUTDigital input default settings Connecting Speakers Surround back speakersFront Bi-Amp Connections Connecting Subwoofer PRE OUT Speaker placementConnecting DC Trigger OUT Connecting Room 2 OutsConnecting Sirius Connector only for North America Connecting for System ControlAC Input Cord SiriusConnect Home TunerFront Panel Controls Remote SensorFluorescent Display Setup MIC Jack Bluetooth in ConnectorFront AUX in Jack Power on button Universal Remote ControlsUP/DOWN / buttons Numeric 0~9, +10 Input Selector buttons ENTER/SEARCH MODE, Select buttonsFunction Table of the Numbered Buttons Loading Batteries Repeat the above steps 1 to 4 for each of your Components Entering a setup codeUsing a punch-through function Removing a punch-through functionRemoving all punch-through functions Operating a macro function Programming a macro functionTo remove a macro program To change a macro programOperations Listening to a Program SourceBefore operation When CD, F.AUX, Video 1~ 3 is selected as an input source Listening with headphonesMuting the sound Surround modes Hall TheaterStadium RoomDolby Truehd Enjoying Surround SoundEnter the test tone mode Adjusting each channel level with test toneCancel the test tone function To cancel the surround mode for stereo operationAdjust the level of the selected channel as desired Adjusting the current channel levelRepeat the above steps 2 and 3 to adjust each channel level Press the Channel Level buttonRecalling the memorized channel levels Memorizing the adjusted channel levelsManual tuning Auto tuningAuto presetting Listening to Radio BroadcastsTuning to preset stations Manual presettingTuning Press the MEMORY/ENTER buttonTo sign up, access the website at Press the Tuning UP+/DOWN- buttons repeatedly to select SRSirius Satellite Radio only for North America Signing up for Sirius Satellite RadioDirect search Category search→ DIR Srch → CAT Srch → OFF Preset search Presetting channelsWhen tuning in the previously locked channels Parental lockTune in the channel you want to lock or unlock To record audio signals Dubbing the audio and video signals separately onto VideoRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Adjusting the brightness of the fluorescent display Operating the sleep timerOther Functions Displaying the operation statusSet the selected mode as desired Press the Room 2 button to enter the Room 2 modeRoom 2 Source Playback Start play on the component related to the Room 2 sourceOSD Menu Settings Select the desired menu using the Cursor UP/DOWN buttonsTurn the menu screen on When selecting the SPEAKER/ROOMEQSETUP When selecting the CH Level SetupWhen selecting the items other than OSD Position Adjust Setting the System SetupWhen selecting the AMP Assign Press the Cursor UP/DOWN buttons to select the desired itemWhen selecting the Subwoofer Mode When selecting the Hdmi Audio OUTWhen selecting the Tone Control When selecting the Momentary OSD When selecting the Cinema EQWhen selecting the OSD Position Adjust When selecting the menu of page 2 or Setting the Input SetupWhen selecting the Video Assign When selecting the Hdmi AssignWhen selecting the Audio Assign When selecting the Audio ModeWhen selecting the AV Sync When selecting the Auto SurroundWhen selecting the DC Trigger When selecting the HD AudioWhen selecting the Name Confirm your entryTo resume its factory input source name When selecting the Parental Lock When selecting the Edit Lock Code Setting the Speaker / Room EQ Setup When selecting the Auto SetupPreparations RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration About the speaker distance When selecting the Speaker DistanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memory modeRepeat the above steps 1 and 2 to adjust each channel level Reference Setting the Sound Parameter When selecting the Night ModeAuto Repeat the above steps 2 and 3 to adjust other parameters When selecting the Dolby Plii MusicWhen selecting the Panorama mode When selecting the Center Width controlWhen selecting the Room Setting the Multi Room SetupWhen selecting the Input When selecting the VolumeProblem Possible Cause Remedy Troubleshooting GuideSpecifications Setup Code Table SSS RCATMK CCEKLH MEISTS NSC ABCHTS SATRD-7503
Top Page Image Contents