Sherwood RD-7503 manual Digital Audio Recording with MD Recorder

Page 36

RD-7503(A)2008.11.41:45PM페이지36

ENGLISH

DIGITAL AUDIO RECORDING WITH MD RECORDER

•Only when the OPTICAL DIGITAL OUT of this receiver is connected to the OPTICAL DIGITAL IN of the MD recorder or CD recorder, you can enjoy high-quality sound of digital recording without converting the original signals. Refer to "CONNECTING VIDEO COMPONENTS", "CONNECTING AUDIO COMPONENTS" and "CONNECTING DIGITAL INS AND OUT" on pages 6 ~8 and the operating instructions of the MD recorder or CD recorder.

�Notes:

•Depending on the digital audio signal format input into the HDMI IN connector, some digital signals cannot be output from the OPTICAL DIGITAL OUT jack.

•Digital recording is available for the digital audio program sources such as CDs, MDs, some DVDs, etc.

•There are some restrictions on recording digital signals. When making digital recordings, refer to the operating instructions of your digital recording equipment to know what restrictions are imposed.

1. Select the desired of CD, F.AUX, VIDEO 1~3 as a recording source.

�In case of recording the digital audio signal input into a HDMI IN connector

•Select the desired recording source to which the HDMI IN is connected and assigned and then perform the steps 3 and 4 (, but ignore the step 2).

�Note :

•If the AUDIO MODE is set to the mode other than "HDMI" for the corresponding recording source on the INPUT SETUP menu, the digital audio signals will not be output and there will be no recording. (For details, refer to "When selecting the AUDIO MODE" on page 46.)

2. For digital recording, select the digital input as recording signal input.

�Note :

•If the AUDIO MODE is set to the mode other than "DIGITAL" for the corresponding recording source on the INPUT SETUP menu, the digital audio signals from the selected digital input will not be output and there will be no recording. (For details, refer to "When CD, F.AUX, VIDEO 1~3 is selected as an input source" on page 22 and "When selecting the AUDIO MODE" on page 46.)

3. Start recording on the component connected to the OPTICAL DIGITAL OUT.

4. Start play on the desired input.

36

Image 36

Contents RD-7503 Important Safety Instructions Introduction Read this Before Operating Your Unit120 Contents Connecting Antennas System ConnectionsConnecting Video Components Connecting Audio Components Component video input default settings *2Hdmi High Definition Multimedia Interface connection *1 Copyright protection systemConnecting External INS Connecting Digital INS and OUTDigital input default settings Connecting Speakers Surround back speakersFront Bi-Amp Connections Speaker placement Connecting Subwoofer PRE OUTConnecting Room 2 Outs Connecting DC Trigger OUTConnecting for System Control Connecting Sirius Connector only for North AmericaAC Input Cord SiriusConnect Home TunerFront Panel Controls Remote SensorFluorescent Display Setup MIC Jack Bluetooth in ConnectorFront AUX in Jack Universal Remote Controls Power on buttonUP/DOWN / buttons Numeric 0~9, +10 Input Selector buttons ENTER/SEARCH MODE, Select buttonsFunction Table of the Numbered Buttons Loading Batteries Entering a setup code Repeat the above steps 1 to 4 for each of your ComponentsUsing a punch-through function Removing a punch-through functionRemoving all punch-through functions Programming a macro function Operating a macro functionTo remove a macro program To change a macro programOperations Listening to a Program SourceBefore operation When CD, F.AUX, Video 1~ 3 is selected as an input source Listening with headphonesMuting the sound Surround modes Theater HallStadium RoomEnjoying Surround Sound Dolby TruehdAdjusting each channel level with test tone Enter the test tone modeCancel the test tone function To cancel the surround mode for stereo operationAdjusting the current channel level Adjust the level of the selected channel as desiredRepeat the above steps 2 and 3 to adjust each channel level Press the Channel Level buttonMemorizing the adjusted channel levels Recalling the memorized channel levelsAuto tuning Manual tuningAuto presetting Listening to Radio BroadcastsManual presetting Tuning to preset stationsTuning Press the MEMORY/ENTER buttonPress the Tuning UP+/DOWN- buttons repeatedly to select SR To sign up, access the website atSirius Satellite Radio only for North America Signing up for Sirius Satellite RadioDirect search Category search→ DIR Srch → CAT Srch → OFF Presetting channels Preset searchWhen tuning in the previously locked channels Parental lockTune in the channel you want to lock or unlock Dubbing the audio and video signals separately onto Video To record audio signalsRecording Dubbing from video components ontoDigital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displayOther Functions Displaying the operation statusPress the Room 2 button to enter the Room 2 mode Set the selected mode as desiredRoom 2 Source Playback Start play on the component related to the Room 2 sourceOSD Menu Settings Select the desired menu using the Cursor UP/DOWN buttonsTurn the menu screen on When selecting the CH Level Setup When selecting the SPEAKER/ROOMEQSETUPSetting the System Setup When selecting the items other than OSD Position AdjustWhen selecting the AMP Assign Press the Cursor UP/DOWN buttons to select the desired itemWhen selecting the Subwoofer Mode When selecting the Hdmi Audio OUTWhen selecting the Tone Control When selecting the Cinema EQ When selecting the Momentary OSDWhen selecting the OSD Position Adjust Setting the Input Setup When selecting the menu of page 2 orWhen selecting the Hdmi Assign When selecting the Video AssignWhen selecting the Audio Assign When selecting the Audio ModeWhen selecting the Auto Surround When selecting the AV SyncWhen selecting the DC Trigger When selecting the HD AudioWhen selecting the Name Confirm your entryTo resume its factory input source name When selecting the Parental Lock When selecting the Edit Lock Code Setting the Speaker / Room EQ Setup When selecting the Auto SetupPreparations RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration When selecting the Speaker Distance About the speaker distanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memory modeRepeat the above steps 1 and 2 to adjust each channel level Reference Setting the Sound Parameter When selecting the Night ModeAuto When selecting the Dolby Plii Music Repeat the above steps 2 and 3 to adjust other parametersWhen selecting the Panorama mode When selecting the Center Width controlSetting the Multi Room Setup When selecting the RoomWhen selecting the Input When selecting the VolumeTroubleshooting Guide Problem Possible Cause RemedySpecifications Setup Code Table RCA SSSTMK CCEKLH MEISTS ABC NSCSAT HTSRD-7503