Sherwood RD-7503 manual Adjusting the current channel level, Press the Channel Level button

Page 27

RD-7503(A)2008.11.41:45PM페이지27

Adjusting the current channel level

•After adjusting each channel level with test tone, adjust the channel levels either according to the program sources or to suit your tastes.

•You can adjust the current channel levels as desired. These adjusted levels are just memorized into user’s memory ("CAL"), not into preset memory("REF 1", "REF 2").

1. Press the CHANNEL LEVEL button.

• Then the memory mode ("CAL", "REF 1", etc) is displayed for several seconds.

• When the memory mode or channel level disappears, press this button again.

ENGLISH

2. Select the desired channel.

• Each time these buttons are pressed, the corresponding channel is selected as follows:

→ CAL (or REF 1, etc.) ↔ FL ← C ← FR ← SR ←

→ <LFE> ↔ SUB ↔ SL(↔SB) or (↔SBL ↔ SBR) ← DTS LFE or Dolby Digital LFE

( ): Possible depending on whether the surround back channel is set to "2 CH" or "1 CH".

< >: Possible only when the digital signals from Dolby Digital, DTS, Dolby TrueHD or DTS HD program sources that include LFE signal are input.

• Depending on the speaker settings("NO", etc.) and surround mode, etc., some channels cannot be selected.

• When the SPEAKER button is set to off, only the Front Left, Front Right(and LFE) channels can be selected.

3. Adjust the level of the selected channel as desired.

• The LFE level can be adjusted within the range of -10 ~ 0 dB and other channel levels within the range of -15 ~ +15 dB.

• In general, we recommend the LFE level to be adjusted to 0 dB.(However, the recommended LFE level for some early DTS software is -10 dB.) If the recommended levels seem too high, lower the setting as necessary.

4. Repeat the above steps 2 and 3 to adjust each channel level.

27

Image 27

Contents RD-7503 Important Safety Instructions Introduction Read this Before Operating Your Unit120 Contents System Connections Connecting AntennasConnecting Video Components Copyright protection system Connecting Audio ComponentsComponent video input default settings *2 Hdmi High Definition Multimedia Interface connection *1Connecting External INS Connecting Digital INS and OUTDigital input default settings Connecting Speakers Surround back speakersFront Bi-Amp Connections Connecting Subwoofer PRE OUT Speaker placementConnecting DC Trigger OUT Connecting Room 2 OutsSiriusConnect Home Tuner Connecting for System ControlConnecting Sirius Connector only for North America AC Input CordFront Panel Controls Remote SensorFluorescent Display Setup MIC Jack Bluetooth in ConnectorFront AUX in Jack ENTER/SEARCH MODE, Select buttons Universal Remote ControlsPower on button UP/DOWN / buttons Numeric 0~9, +10 Input Selector buttonsFunction Table of the Numbered Buttons Loading Batteries Repeat the above steps 1 to 4 for each of your Components Entering a setup codeUsing a punch-through function Removing a punch-through functionRemoving all punch-through functions To change a macro program Programming a macro functionOperating a macro function To remove a macro programOperations Listening to a Program SourceBefore operation When CD, F.AUX, Video 1~ 3 is selected as an input source Listening with headphonesMuting the sound Surround modes Room TheaterHall StadiumDolby Truehd Enjoying Surround SoundTo cancel the surround mode for stereo operation Adjusting each channel level with test toneEnter the test tone mode Cancel the test tone functionPress the Channel Level button Adjusting the current channel levelAdjust the level of the selected channel as desired Repeat the above steps 2 and 3 to adjust each channel levelRecalling the memorized channel levels Memorizing the adjusted channel levelsListening to Radio Broadcasts Auto tuningManual tuning Auto presettingPress the MEMORY/ENTER button Manual presettingTuning to preset stations TuningSigning up for Sirius Satellite Radio Press the Tuning UP+/DOWN- buttons repeatedly to select SRTo sign up, access the website at Sirius Satellite Radio only for North AmericaDirect search Category search→ DIR Srch → CAT Srch → OFF Preset search Presetting channelsWhen tuning in the previously locked channels Parental lockTune in the channel you want to lock or unlock Dubbing from video components onto Dubbing the audio and video signals separately onto VideoTo record audio signals RecordingDigital Audio Recording with MD Recorder Displaying the operation status Operating the sleep timerAdjusting the brightness of the fluorescent display Other FunctionsStart play on the component related to the Room 2 source Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Room 2 Source PlaybackOSD Menu Settings Select the desired menu using the Cursor UP/DOWN buttonsTurn the menu screen on When selecting the SPEAKER/ROOMEQSETUP When selecting the CH Level SetupPress the Cursor UP/DOWN buttons to select the desired item Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the AMP AssignWhen selecting the Subwoofer Mode When selecting the Hdmi Audio OUTWhen selecting the Tone Control When selecting the Momentary OSD When selecting the Cinema EQWhen selecting the OSD Position Adjust When selecting the menu of page 2 or Setting the Input SetupWhen selecting the Audio Mode When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio AssignWhen selecting the HD Audio When selecting the Auto SurroundWhen selecting the AV Sync When selecting the DC TriggerWhen selecting the Name Confirm your entryTo resume its factory input source name When selecting the Parental Lock When selecting the Edit Lock Code Setting the Speaker / Room EQ Setup When selecting the Auto SetupPreparations RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration About the speaker distance When selecting the Speaker DistanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memory modeRepeat the above steps 1 and 2 to adjust each channel level Reference Setting the Sound Parameter When selecting the Night ModeAuto When selecting the Center Width control When selecting the Dolby Plii MusicRepeat the above steps 2 and 3 to adjust other parameters When selecting the Panorama modeWhen selecting the Volume Setting the Multi Room SetupWhen selecting the Room When selecting the InputProblem Possible Cause Remedy Troubleshooting GuideSpecifications Setup Code Table CCE RCASSS TMKKLH MEISTS NSC ABCHTS SATRD-7503