Sherwood RD-7503 Setting the Speaker / Room EQ Setup, When selecting the Auto Setup, Preparations

Page 51

RD-7503(A)2008.11.41:45PM페이지51

SETTING THE SPEAKER / ROOM EQ SETUP

•After you have installed this receiver and connected all the components, you should adjust the speaker settings for the optimum sound acoustics according to your environment and speaker layout.

•Even when you change speakers, speaker positions, or the layout of your listening environment, you should adjust the speaker settings, too.

•When performing the AUTO SETUP procedure, you need not perform the SPEAKER CONFIGURATION, SPEAKER DISTANCE, SPEAKER CROSSOVER and CH LEVEL SETUP procedures.

• AUTO SETUP : To set the speaker setup and channel level setup automatically.

• SPEAKER CONFIGURATION : To adjust the speakers depending on whether they are connected or not.

• SPEAKER DISTANCE: To select the distance between the listening position and each speaker to set the delay time automatically for optimum surround playback.

•SPEAKER CROSSOVER : To select the desired crossover frequency.

• ROOM EQ SETUP : To select the desired room EQ mode.

When selecting the AUTO SETUP

•Auto Setup lets you avoid troublesome listening-based speaker setup and achieve good surround sound. Auto Setup has the feature that provides the optimum listening environment at the listening position in your room, where there are often multiple listeners viewing programs together.

You should connect the supplied microphone to the SETUP MIC jack so that this receiver can analyze the information from a series of test tones emitted from speakers at main listening position and can adjust the configuration, distance, sound level, crossover frequency and frequency response of each speaker automatically.

•If you want to personalize your speaker setup and channel level setup by making the settings manually, perform the "When selecting the SPEAKER CONFIGURATION" on page 53, "When selecting the SPEAKER DISTANCE" on page 54, "When selecting the SPEAKER CROSSOVER" on page 55, "Adjusting each channel level with test tone" on page 26 and "Adjusting the current channel level" on page 27.

•After the auto setup has been completed, set the room EQ as desired. (For details, refer to "When selecting the ROOM EQ SETUP" on page 56.)

�Preparations

①. Check that the speakers are securely connected to this receiver.

•If your subwoofer has adjustable volume and crossover frequency, set the volume halfway and set the crossover frequency to the maximum or the low pass filter off.

②. Connect the supplied microphone to the SETUP MIC jack on the front panel.(For details, refer to "SETUP MIC JACK" on page 14.)

■Notes :

•Because the microphone for Auto Setup is designed for use with this receiver, to use the auto setup function, do not use a microphone other than the one supplied with this receiver.

•After you have completed the auto setup procedure, disconnect the microphone.

1. Place the microphone on a flat level surface at the listening position.

•If possible, use a tripod, etc. to attach the microphone at the same height as your ears would be when you are seated in your listening position.

•Ensure there are no obstacles between the speakers and the microphone.

ENGLISH

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents RD-7503 Important Safety Instructions Introduction Read this Before Operating Your Unit120 Contents System Connections Connecting AntennasConnecting Video Components Copyright protection system Connecting Audio ComponentsComponent video input default settings *2 Hdmi High Definition Multimedia Interface connection *1Connecting External INS Connecting Digital INS and OUTDigital input default settings Connecting Speakers Surround back speakersFront Bi-Amp Connections Connecting Subwoofer PRE OUT Speaker placementConnecting DC Trigger OUT Connecting Room 2 OutsSiriusConnect Home Tuner Connecting for System ControlConnecting Sirius Connector only for North America AC Input CordFront Panel Controls Remote SensorFluorescent Display Setup MIC Jack Bluetooth in ConnectorFront AUX in Jack ENTER/SEARCH MODE, Select buttons Universal Remote ControlsPower on button UP/DOWN / buttons Numeric 0~9, +10 Input Selector buttonsFunction Table of the Numbered Buttons Loading Batteries Repeat the above steps 1 to 4 for each of your Components Entering a setup codeUsing a punch-through function Removing a punch-through functionRemoving all punch-through functions To change a macro program Programming a macro functionOperating a macro function To remove a macro programOperations Listening to a Program SourceBefore operation When CD, F.AUX, Video 1~ 3 is selected as an input source Listening with headphonesMuting the sound Surround modes Room TheaterHall StadiumDolby Truehd Enjoying Surround SoundTo cancel the surround mode for stereo operation Adjusting each channel level with test toneEnter the test tone mode Cancel the test tone functionPress the Channel Level button Adjusting the current channel levelAdjust the level of the selected channel as desired Repeat the above steps 2 and 3 to adjust each channel levelRecalling the memorized channel levels Memorizing the adjusted channel levelsListening to Radio Broadcasts Auto tuningManual tuning Auto presettingPress the MEMORY/ENTER button Manual presettingTuning to preset stations TuningSigning up for Sirius Satellite Radio Press the Tuning UP+/DOWN- buttons repeatedly to select SRTo sign up, access the website at Sirius Satellite Radio only for North AmericaDirect search Category search→ DIR Srch → CAT Srch → OFF Preset search Presetting channelsWhen tuning in the previously locked channels Parental lockTune in the channel you want to lock or unlock Dubbing from video components onto Dubbing the audio and video signals separately onto VideoTo record audio signals RecordingDigital Audio Recording with MD Recorder Displaying the operation status Operating the sleep timerAdjusting the brightness of the fluorescent display Other FunctionsStart play on the component related to the Room 2 source Press the Room 2 button to enter the Room 2 modeSet the selected mode as desired Room 2 Source PlaybackOSD Menu Settings Select the desired menu using the Cursor UP/DOWN buttonsTurn the menu screen on When selecting the SPEAKER/ROOMEQSETUP When selecting the CH Level SetupPress the Cursor UP/DOWN buttons to select the desired item Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the AMP AssignWhen selecting the Subwoofer Mode When selecting the Hdmi Audio OUTWhen selecting the Tone Control When selecting the Momentary OSD When selecting the Cinema EQWhen selecting the OSD Position Adjust When selecting the menu of page 2 or Setting the Input SetupWhen selecting the Audio Mode When selecting the Hdmi AssignWhen selecting the Video Assign When selecting the Audio AssignWhen selecting the HD Audio When selecting the Auto SurroundWhen selecting the AV Sync When selecting the DC TriggerWhen selecting the Name Confirm your entryTo resume its factory input source name When selecting the Parental Lock When selecting the Edit Lock Code Setting the Speaker / Room EQ Setup When selecting the Auto SetupPreparations RD-7503A2008.11.4145PM페이지52 When selecting the Speaker Configuration About the speaker distance When selecting the Speaker DistanceWhen selecting the Speaker Crossover When selecting the Room EQ Setup Setting the CH Level Setup Memory modeRepeat the above steps 1 and 2 to adjust each channel level Reference Setting the Sound Parameter When selecting the Night ModeAuto When selecting the Center Width control When selecting the Dolby Plii MusicRepeat the above steps 2 and 3 to adjust other parameters When selecting the Panorama modeWhen selecting the Volume Setting the Multi Room SetupWhen selecting the Room When selecting the InputProblem Possible Cause Remedy Troubleshooting GuideSpecifications Setup Code Table CCE RCASSS TMKKLH MEISTS NSC ABCHTS SATRD-7503
Top Page Image Contents